[Lsdmeasap]

Well, than add some MCH for sure.

I am not so sure about GA-P45 yet, but GA-P35 and crucial did not play well together.

I see you say MCH on AUTO, as well as the rest.... That is likely a major part of the issue. You are going to need to manually adjust your CPU voltage for sure, I'd suggest start high and then lower and test until it fails then raise back up again. 1.35 or so should be plenty high for only 400FSB

Try this for 3.6 @ 400 FSB with ram at 1000 for now >>>>

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............:
CPU Clock Ratio ..........................: 9
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................: 3.600


Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............:400 Mhz
PCI Express Frequency (Mhz) .........:Set to 100


Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<< Leave
PCI Express Clock Drive.................: <<< Leave
CPU Clock Skew (ps)....................: <<< Leave
MCH Clock Skew (ps)...................: <<< Leave


DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 2.5 ( 400X2.5=1000MHz)
Memory Frequency (Mhz) ..............: 1000Mhz
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time........................5
tRCD .........................................5
tRP'...........................................5
tRAS..........................................12

Advanced Timing Control [Press Enter]
tRRD...........................................3-4
tWTR..........................................9-11
tWR............................................3-5
tRFC...........................................42-52
tRTP...........................................3-6
Command Rate (CMD) ....................:2

Channel A
Static tRead Value.........................:7-10
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Channel B
Static tRead Value.........................:7-10
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Motherboard Voltage Control
Voltage Type.………... Manual
CPU
CPU Vcore….……….........................:1.325-1.365 (Try 1.35 then lower as you test)
CPU Termination…..... 1.200V*.......: <<< Leave
CPU PLL…………………....1.500V*.......: <<< Leave
CPU Referen.…………....0.755V*.......: <<< Leave
CPU Reference2………,,0.800V*.......:<<< Leave

MCH/ICH
MCH Core…………….....1.100V...........: << Add +1 for stability
MCH Reference….…….0.800V...........; <<< Leave
MCH/DRAM Ref.…......0.900V...........: <<< Leave
ICH I/O……………….....1.550V............: <<< Leave
ICH Core…………...……1.100V............: <<< Leave

DRAM
DRAM Voltage ……....1.800V............: Set to 2.1V
DRAM Termination .…0.900V............: <<< Leave
Channel A Reference 0.900V............: <<< Leave
Channel B Reference 0.900V............: <<< Leave

Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Disabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]