[Lsdmeasap]

Ok, Here is some ranges for you to start with. I know it is a big BIOS page isnt it! have you read thru the 2 Guides I have pinned? If not, when you get some time please do as it will help you understand things a little better so you can be more comfortable with it.

Voltage changes are fine as long as you do not try to set things super high in a attempt to make something work as this is usually not the issue unless someone has told you something is way to low. All below voltage changes are safe, and normal for 2x2GB. I did not suggest any CPU related voltages as it looks as if you are not overclocking.

Hope this helps you for now, if not I will see you tomorrow as I am on my way out the door for the night.

Good luck

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto
CPU Clock Ratio ..........................: 9x
Fine CPU Clock Ratio.....................:.5
CPU Frequency ...........................: 2.53Ghz


Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 266Mhz
PCI Express Frequency (Mhz) .........:Set to 100


Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 800
PCI Express Clock Drive.................: 900
CPU Clock Skew (ps)....................: <<< Leave
MCH Clock Skew (ps)...................: <<< Leave


DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto] << You can try 400 if you like, if there is a letter beside the 4.00 below >>>
System Memory Multiplier ..............: 4.00
Memory Frequency (Mhz) ..............: 1066
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time........................:5
tRCD .........................................: 5
tRP'............................................: 5
tRAS..........................................: 15/18 (Set to 15 later, will likely work now just fine)


These are ranges below, set all high first, then lower one at a time later and test after each move


Advanced Timing Control [Press Enter]
tRRD...........................................: 3-4
tWTR..........................................: (Try 4-6 Last) 9-11
tWR............................................: (Try 3-5 Last) 6-8
tRFC...........................................: 52-62 (likely will run fine at 50-52 once tweaked)
tRTP...........................................: 3-6
Command Rate (CMD) ....................:2 (changed, was 0) <<< Good 2 is correct

Channel A
Static tRead Value.........................:7-10 << I see you did not add anything? 7-10 is suggested
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Channel B
Static tRead Value.........................:7-10
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Motherboard Voltage Control
Voltage Type.………... Manual
CPU
CPU Vcore….……….........................: 1.06250v
CPU Termination…..... 1.200V*.......: <<< Leave
CPU PLL…………………....1.500V*.......: <<< Leave
CPU Referen.…………....0.755V*.......: <<< Leave
CPU Reference2………,,0.800V*.......:<<< Leave

MCH/ICH
MCH Core…………….....1.100V...........: << Try 1.3 (May need only 1.25 or so)
MCH Reference….…….0.800V...........; <<< Leave
MCH/DRAM Ref.…......0.900V...........: <<< Leave
ICH I/O……………….....1.550V............: <<< Leave
ICH Core…………...……1.100V............: <<< Leave

DRAM
DRAM Voltage ……....1.800V............: Set to 2.1V
DRAM Termination .…0.900V............: <<< Leave
Channel A Reference 0.900V............: <<< Leave
Channel B Reference 0.900V............: <<< Leave

Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Disabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]