DO NOT use all of my voltage settings in the latter images, as many of them are motherboard or CPU specific and you would need to find your hardware’s own stable voltage ranges.
And, as always, if you do need help, I am here to offer it!
General settings for P35 and P45 boards for the speeds posted above
800Mhz
P35
Code:
Robust Graphics Booster___________ [Auto or Fast]
CPU Clock Ratio ____________ [x]
Fine Clock Ratio ____________[0.0]
CPU Host Clock Control_ [Enabled]
CPU Host Frequency (MHz)__________ [333]
PCI Express Frequency (Mhz)_______ [100]
C.I.A. 2__________________________ [Disabled]
System Memory Multiplier (SPD)____ [2.40]
DRAM Timing Selectable_______ SPD __ [Manual]
Performance Enhance = [Standard]
CAS Latency Time________________ 5
Dram RAS# to CAS# Delay_________ 4
Dram RAS# Precharge Delay_______ 4
Precharge Delay (tRAS)__________ 12
ACT to ACT Delay (tRRD)_________ 3
Rank Write to READ Delay________ 3-4
Write to Precharge Delay_________ 4-6
Refresh to ACT Delay______________ 48-52
Read to Precharge Delay__________ 3
Static tRead Value_______________ 6-7
Static tRead Phase Adjust________ [Auto]
System Voltage Control____ [Manual]
DDR2 OverVoltage Control__ [+0.1V - +0.3V] = 1.9V - 2.1V
PCI-E OverVoltage Control_ [+0.1V]
FSB OverVoltage Control___ [+0.1V]
(G)MCH OverVoltage Control [+0.1V - 0.2V]
CPU Voltage Control_______ [x.xx]
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC
Integrated Peripherals
Legacy USB Storage Detect___________________[Disabled] *Note* Must be enabled to flash from USB
P45
Code:
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto or Fast
CPU Clock Ratio ..........................: x
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................: x.xx
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 333Mhz
PCI Express Frequency (Mhz) .........:Set to 100
C.I.A.2 .................................:[Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<< 800
PCI Express Clock Drive.................: <<< 900
CPU Clock Skew (ps)....................: <<<
MCH Clock Skew (ps)...................: <<<
DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 2.40B
Memory Frequency (Mhz) ..............: 800Mhz
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time........................ 5
tRCD ......................................... 4
tRP'........................................... 4
tRAS.......................................... 12
Advanced Timing Control
tRRD........................................... 3
tWTR.......................................... 3-4
tWR............................................ 4-6
tRFC........................................... 48-52
tRTP........................................... 3
Command Rate (CMD) ....................:2
Driving Strength Profiles
Driving Strength ............................ 1066
Channel A
Static tRead Value.........................:6-7 (Depending on other voltages and strap being used)
tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Channel B
Static tRead Value.........................:6-7 (Depending on other voltages and strap being used)
tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Motherboard Voltage Control
Voltage Type.………... Manual
CPU
CPU Vcore….……….........................: x.xx
CPU Termination…..... 1.200V*.......: << If overclocking Please set to stock, Auto overvolts this way to much. Optimal range for overclock would be 1.2-1.5 depending on Vcore, try to keep at least .1 under vcore. Auto is fine if not overclocking
CPU PLL…………………....1.500V*.......: << If overclocking Please set to stock, Auto overvolts this way to much. Optimal range for overclock would be 1.5-1.65. Auto is fine if not overclocking
CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly
CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly
MCH/ICH
MCH Core…………….....1.100V...........: << 1.2-1.26 (amount needed will depend on Strap used and tRD used)
MCH Reference….…….0.800V...........; <<< May need adjusted, depends on your board and CPU being used, and all other voltages. See my signature for how to adjust.
MCH/DRAM Ref.…......0.900V...........: <<< Leave
ICH I/O……………….....1.550V............: <<< 1.5-1.55
ICH Core…………...……1.100V............: <<< 1.14-1.2
DRAM
DRAM Voltage ……....1.800V............: 1.9-2.1V
DRAM Termination .…0.900V............: <<< Leave
Channel A Reference 0.900V............: <<< Leave
Channel B Reference 0.900V............: <<< Leave
Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC
Integrated Peripherals
Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB