900Mhz
P35
Code:
Robust Graphics Booster___________ [Auto or Fast]
CPU Clock Ratio ____________ [x]
Fine Clock Ratio ____________[0.0]
CPU Host Clock Control_ [Enabled]
CPU Host Frequency (MHz)__________ [450]
PCI Express Frequency (Mhz)_______ [100]
C.I.A. 2__________________________ [Disabled]
System Memory Multiplier (SPD)____ [2.00]
DRAM Timing Selectable_______ SPD __ [Manual]
Performance Enhance = [Standard]
CAS Latency Time________________ 5
Dram RAS# to CAS# Delay_________ 5
Dram RAS# Precharge Delay_______ 4
Precharge Delay (tRAS)__________ 12
ACT to ACT Delay (tRRD)_________ 3
Rank Write to READ Delay________ 3-4
Write to Precharge Delay_________ 5-6
Refresh to ACT Delay______________ 52
Read to Precharge Delay__________ 3
Static tRead Value_______________ 7-9
Static tRead Phase Adjust________ [Auto]
System Voltage Control____ [Manual]
DDR2 OverVoltage Control__ [+0.2V - +0.3V] = 2.0V - 2.1V
PCI-E OverVoltage Control_ [+0.1V]
FSB OverVoltage Control___ [+0.1V]
(G)MCH OverVoltage Control [+0.1V - 0.2V]
CPU Voltage Control_______ [x.xx]
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC
Integrated Peripherals
Legacy USB Storage Detect___________________[Disabled] *Note* Must be enabled to flash from USB
P45
Code:
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto or Fast
CPU Clock Ratio ..........................: x
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................: x.xx
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 450Mhz
PCI Express Frequency (Mhz) .........:Set to 100
C.I.A.2 .................................:[Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<< 800
PCI Express Clock Drive.................: <<< 900
CPU Clock Skew (ps)....................: <<<
MCH Clock Skew (ps)...................: <<<
DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 2.00B or 2.00D
Memory Frequency (Mhz) ..............: 900Mhz
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time........................ 5
tRCD ......................................... 5
tRP'........................................... 4
tRAS.......................................... 12
Advanced Timing Control
tRRD........................................... 3
tWTR.......................................... 3-4
tWR............................................ 5-6
tRFC........................................... 52
tRTP........................................... 3
Command Rate (CMD) ....................:2
Driving Strength Profiles
Driving Strength ............................ 1066
Channel A
Static tRead Value.........................:8-9 (Depending on other voltages and strap being used)
tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Channel B
Static tRead Value.........................:8-9 (Depending on other voltages and strap being used)
tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Motherboard Voltage Control
Voltage Type.………... Manual
CPU
CPU Vcore….……….........................: x.xx
CPU Termination…..... 1.200V*.......: << If overclocking Please set to stock, Auto overvolts this way to much. Optimal range for overclock would be 1.2-1.5 depending on Vcore, try to keep at least .1 under vcore. Auto is fine if not overclocking
CPU PLL…………………....1.500V*.......: << If overclocking Please set to stock, Auto overvolts this way to much. Optimal range for overclock would be 1.5-1.65. Auto is fine if not overclocking
CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly
CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly
MCH/ICH
MCH Core…………….....1.100V...........: << 1.2-1.26 (amount needed will depend on Strap used and tRD used)
MCH Reference….…….0.800V...........; <<< May need adjusted, depends on your board and CPU being used, and all other voltages. See my signature for how to adjust.
MCH/DRAM Ref.…......0.900V...........: <<< Leave
ICH I/O……………….....1.550V............: <<< 1.5-1.55
ICH Core…………...……1.100V............: <<< 1.14-1.2
DRAM
DRAM Voltage ……....1.800V............: 2.0-2.1V
DRAM Termination .…0.900V............: <<< Leave
Channel A Reference 0.900V............: <<< Leave
Channel B Reference 0.900V............: <<< Leave
Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC
Integrated Peripherals
Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB