|
03-24-2009, 01:38 AM
|
|||
|
|||
First OC Q9550
Mobo: Gigabyte EP45-UD3P CPU: Q9550 CPU Cooler: Arctic Freezer 7 Pro Mem: G.SKILL 4GB (2 x 2GB) DDR2 1066 (PC2 8500) 5-5-5-15 Newegg.com - G.SKILL 4GB (2 x 2GB) 240-Pin DDR2 SDRAM DDR2 1066 (PC2 8500) Dual Channel Kit Desktop Memory - Desktop Memory PSU: Corsair 650 Watt Case: Coooler Master Storm Sniper 2x200 fans, 2x120 fans. Again, for first OC, looking to go to 3.2 GHz. Settings, at the moment: MB Intelligent Tweaker(M.I.T.) Robust graphics Booster: Auto CPU Clock Ratio: 8 Fine CPU Clock Ratio: +0.5 CPU Frequency: 2.83 GHz (333x8.5) Clock Chip Control CPU Clock Control: Disabled CPU Host Frequency: 333 MHz PCI Express Frequency: 100 CIA2: Disabled Advanced Clck Control CPU Clock Drive: 700mv PCI Express Clock Drive: 700mv CPU Clock Skew: 0ps MCH Clock Skew: 0ps DRAM Performance Control Performance Enhance: Standard Extreme Memory Profile: (X.M.P.): Auto MCH Frquency Latch: Auto System Memory Multiplier (SPD): Auto Memory Frequency (MHz): 1066 DRAM Timing Selectable (SPD): Auto Standard Timing Control CAS Latency Time: 5 tRCD: 5 tRP: 5 tRAS: 15 Advanced Timing Control tRRD: 4 Auto tWTR 4 Auto tWR 13 Auto tRFC 68 Auto tRTP4 Auto Command Rate (CMD) 0 Auto Driving Strength Profiles All on Auto Channel A Settings Static tRead Value: 6 Auto tRD Phase0 Adjustment: 0 Auto tRD Phase1 Adjustment: 0 Auto tRD Phase2 Adjustment: 0 Auto tRD Phase3 Adjustment: 0 Auto Trd2rd(Different Rank): 8 Auto Twr2wr(Different Rank): 8 Auto Twr2rd(Different Rank): 7 Auto Trd2wr(Same/Diff Rank): 9 Auto Dimm1 Clock Skew Control: Auto Dimm2 Clock Skew Control: Auto DDR Write Training: Auto Channel B Same as Channel A Motherboard Voltage Control CPU Load Line Calibration: Disabled CPU Vcore: 1.23750V Auto CPU Termination: 1.200V Auto CPU PLL 1.500V Auto CPU Reference: 0.76V Auto MCH/ICH MCH Core: 1.100V Auto MCH Reference: 0.76 Auto MCH/DRAM Reference: 0.900V Auto ICH I/O: 1.500V Auto ICH Core: 1.100 Auto DRAM DRAM Voltage: 1.800V Auto DRAM Termination: 0.900V Auto Channel A Reference: 0.900V Auto Channel B Reference: 0.900V Auto Advanced Settings Limit CPUID Max. to 3: Disabled No-Execute Memory Protect: Enabled CPU Enhanced Halt (C1E) Enabled C2/C2E State Support: Disabled x C4/C4E State Support: Disabled CPU Thermal Monitor 2(TM2): Enabled CPU EIST Function: Enabled Virtualization Technology: Enabled Integrated Peripherals Legacy USB Storage Detect: Enabled     
|
|
03-24-2009, 02:25 PM
|
||||
|
||||
|
Re: First OC Q9550
You need to start over. Please go into the BIOS and load and apply optimized defaults, then set your ram voltage only and save/apply/reboot BACK to the BIOS. You will then need to set all your changed settings again as they will be reset. This includes, and do not forget especially if you are running RAID, SATA And Disk settings in Advanced BIOS, and Integrated Peripherals page.
I can help once you do that, you cannot start overclocking from Fail Safe settings as many hidden per hardware settings may be incorrect, as well as ones I can visibly see that are. Please see this thread for all Optimized Default steps needed if you are running RAID >> BIOS Flashing - A "How To ~ Qflash Guide"
__________________
|
|
03-24-2009, 05:04 PM
|
||||
|
||||
|
Re: First OC Q9550
K, when you get back in give me your settings you are using now and I will advise back
__________________
|
|
03-25-2009, 12:35 AM
|
|||
|
|||
|
Re: First OC Q9550
OK
Here's the new settings: MB Intelligent Tweaker(M.I.T.) Robust graphics Booster----------------------Auto CPU Clock Ratio------------------------------8 Fine CPU Clock Ratio-------------------------+0.5 CPU Frequency------------------------------2.83 GHz (333x8.5) Clock Chip Control CPU Clock Control---------------------------Disabled CPU Host Frequency------------------------333 MHz PCI Express Frequency----------------------Auto (100) CIA2---------------------------------------Disabled Advanced Clck Control CPU Clock Drive-----------------------------800mv PCI Express Clock Drive----------------------900mv CPU Clock Skew-----------------------------0ps MCH Clock Skew-----------------------------0ps DRAM Performance Control Performance Enhance: Turbo Extreme Memory Profile: (X.M.P.)-----------Auto MCH Frquency Latch-----------------------Auto System Memory Multiplier (SPD)------------Auto Memory Frequency (MHz)------------------1066 DRAM Timing Selectable (SPD)--------------Auto Standard Timing Control CAS Latency Time--------------------------5 tRCD---------------------------------------5 tRP----------------------------------------5 tRAS---------------------------------------15 Advanced Timing Control tRRD--------------------------------------4 Auto tWTR-------------------------------------4 Auto tWR--------------------------------------13 Auto tRFC--------------------------------------68 Auto tRTP4-------------------------------------Auto Command Rate (CMD)----------------------0 Auto Driving Strength Profiles--------------------All on Auto Channel A Settings Static tRead Value-------------------------6 Auto tRD Phase0 Adjustment---------------------0 Auto tRD Phase1 Adjustment---------------------0 Auto tRD Phase2 Adjustment---------------------0 Auto tRD Phase3 Adjustment---------------------0 Auto Trd2rd(Different Rank)----------------------8 Auto Twr2wr(Different Rank)---------------------8 Auto Twr2rd(Different Rank)---------------------7 Auto Trd2wr(Same/Diff Rank)--------------------9 Auto Dimm1 Clock Skew Control------------------Auto Dimm2 Clock Skew Control-----------------Auto DDR Write Training-------------------------Auto Channel B----------------------------------Same as Channel A Motherboard Voltage Control CPU Load Line Calibration----------------------Disabled CPU Vcore--------------------------------1.23750V Auto CPU Termination--------------------------1.200V Auto CPU PLL----------------------------------1.500V Auto CPU Reference----------------------------0.76V Auto MCH/ICH MCH Core--------------------------------1.100V Auto MCH Reference---------------------------0.76 Auto MCH/DRAM Reference---------------------0.900V Auto ICH I/O----------------------------------1.500V Auto ICH Core---------------------------------1.100 Auto DRAM DRAM Voltage----------------------------2.000V Auto DRAM Termination------------------------0.900V Auto Channel A Reference----------------------0.900V Auto Channel B Reference----------------------0.900V Auto Advanced Settings Limit CPUID Max. to 3---------------------Disabled No-Execute Memory Protect---------------Enabled CPU Enhanced Halt (C1E)------------------Enabled C2/C2E State Support---------------------Disabled x C4/C4E State Support-------------------Disabled CPU Thermal Monitor 2(TM2)---------------Enabled CPU EIST Function------------------------Enabled Virtualization Technology------------------Enabled Integrated Peripherals Legacy USB Storage Detect----------------Enabled
|
|
03-25-2009, 03:55 PM
|
||||
|
||||
|
Re: First OC Q9550
Try this for 3.2, I give a few ways trying to keep your ram above 1000. You can also use CPU multi 8/8.5x400 FSB but your ram will need to run 900-960 that way >>>
Robust graphics Booster----------------------Auto or Fast CPU Clock Ratio------------------------------7 Fine CPU Clock Ratio-------------------------+0.5 CPU Frequency------------------------------3.187 (425x7.5) Clock Chip Control CPU Clock Control---------------------------Enabled CPU Host Frequency------------------------425 MHz PCI Express Frequency----------------------Set 100 Manually CIA2---------------------------------------Disabled OR CPU Clock Ratio------------------------------7 Fine CPU Clock Ratio-------------------------+0.0 CPU Frequency------------------------------3.150 (450x7) Clock Chip Control CPU Clock Control---------------------------Enabled CPU Host Frequency------------------------450 MHz PCI Express Frequency----------------------Set 100 Manually CIA2---------------------------------------Disabled Advanced Clck Control CPU Clock Drive-----------------------------800mv PCI Express Clock Drive----------------------900mv CPU Clock Skew-----------------------------0ps MCH Clock Skew-----------------------------0ps DRAM Performance Control Performance Enhance: Turbo << Standard (You can try turbo later but it may need looser settings or more MCH/Ram/Vtt voltages) Extreme Memory Profile: (X.M.P.)-----------Disabled MCH Frquency Latch-----------------------Auto System Memory Multiplier (SPD)------------2.40B Memory Frequency (MHz)------------------1020 (if using 425 FSB) 1080 (If using 450 FSB) DRAM Timing Selectable (SPD)--------------Manual Standard Timing Control CAS Latency Time--------------------------5 tRCD---------------------------------------5 tRP----------------------------------------5 tRAS---------------------------------------15 Set below settings to highest suggested, then later lower one at a time testing as you go with Memtest86+ Advanced Timing Control tRRD--------------------------------------3-4 tWTR-------------------------------------3-5 tWR--------------------------------------4-6 tRFC--------------------------------------52-62 tRTP4-------------------------------------3-5 Command Rate (CMD)----------------------2 Driving Strength Profiles-------------------- Set 1066 Channel A Settings Static tRead Value-------------------------6-10 (6-7 should be fine) tRD Phase0 Adjustment---------------------0 Auto tRD Phase1 Adjustment---------------------0 Auto tRD Phase2 Adjustment---------------------0 Auto tRD Phase3 Adjustment---------------------0 Auto Trd2rd(Different Rank)----------------------8 Auto Twr2wr(Different Rank)---------------------8 Auto Twr2rd(Different Rank)---------------------7 Auto Trd2wr(Same/Diff Rank)--------------------9 Auto Dimm1 Clock Skew Control------------------Auto Dimm2 Clock Skew Control-----------------Auto DDR Write Training-------------------------Auto Channel B----------------------------------Same as Channel A Motherboard Voltage Control CPU Load Line Calibration----------------------Disabled CPU Vcore--------------------------------1.225-1.35 << you will need to find and set your own voltage, more or less may be needed. Keep in mind what you set here will be less in windows at idle and less then that at load. You can check the actual value with CPU-z CPU Termination--------------------------1.2-1.28 should be plenty (DO SET CPU Termination and PLL manually Auto will give to much when overclocking) CPU PLL----------------------------------1.55 CPU Reference----------------------------0.76V Auto MCH/ICH MCH Core--------------------------------1.2-1.24 MCH Reference---------------------------0.76 Auto MCH/DRAM Reference---------------------0.900V Auto ICH I/O----------------------------------1.55 ICH Core---------------------------------1.14 DRAM DRAM Voltage----------------------------2.0-2.1V DRAM Termination------------------------0.900V Auto Channel A Reference----------------------0.900V Auto Channel B Reference----------------------0.900V Auto Advanced Settings Limit CPUID Max. to 3---------------------Disabled No-Execute Memory Protect---------------Enabled CPU Enhanced Halt (C1E)------------------Enabled << Disabled C2/C2E State Support---------------------Disabled x C4/C4E State Support-------------------Disabled CPU Thermal Monitor 2(TM2)---------------Enabled CPU EIST Function------------------------Enabled << Disabled Virtualization Technology------------------Enabled Integrated Peripherals Legacy USB Storage Detect----------------Enabled
__________________
|
|
03-26-2009, 02:20 PM
|
||||
|
||||
|
Re: First OC Q9550
Those temps look fine, but you do need to Disable C1E and EIST still of course, just incase you are overlooking that when you get started.
Good luck and keep us posted on your progress and tweaking results
__________________
|
|
03-26-2009, 06:58 PM
|
|||
|
|||
|
Re: First OC Q9550
Quote:
Quote:
|
|
03-26-2009, 07:08 PM
|
||||
|
||||
|
Re: First OC Q9550
K, Good luck and see ya soon!
__________________
|
 |
| Bookmarks |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
| Display Modes | Rate This Thread |
|
|
Linear Mode
