GA-EP45-DS3R (e7200)

[Dweirdo]

laker faker, im with you on this, E7300 with with Ep45-DS3R, only 3.2 got stable, cant get it over it, either we both have bad chips, or we both nabz, or those motherboard with this cpu is not good XD

[Lsdmeasap]

Ya, what you set in the BIOS for CPU voltage will be about .6 or so different in windows because of vdrop, and Less then that at full load. So you may need far more then you are trying, but likely not for only 3.4 or so

What is your full settings you are using now that is stable?

[laker_faker]

ok so after few other hours of trying, i was stable on 3,5 Ghz, then i tryed ,6 it wasnt stable so i went back to 3,5 and it wasnt stable anymore on same setup, 3,3 wasnt stabel too, i realy dont understand it, i setup it 100% same and one time stable one time not, WTF???
now im on 3,1 and i will cechk in night if its stable
my setings atm:

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............:
CPU Clock Ratio ..........................:
Fine CPU Clock Ratio.....................:.9
CPU Frequency ...........................: 0.5


Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 333 Mhz
PCI Express Frequency (Mhz) .........:Auto (i know..)

C.I.A.2 .................................:[Disabled]


Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 800
PCI Express Clock Drive.................: 900
CPU Clock Skew (ps)....................: 0
MCH Clock Skew (ps)...................: 0


DRAM Performance Control
Performance Enhance...................: [Turbo]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 2.00
Memory Frequency (Mhz) ..............: 667
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time........................5
tRCD .........................................5
tRP'...........................................5
tRAS..........................................18

Advanced Timing Control
tRRD...........................................aut o
tWTR..........................................auto
tWR............................................aut o
tRFC...........................................60
tRTP...........................................aut o
Command Rate (CMD) ....................:2auto

Driving Strength Profiles
Driving Strength ............................

Channel A
Static tRead Value.........................:auto
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Channel B
Static tRead Value.........................:auto
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Motherboard Voltage Control
Voltage Type.………... Manual
CPU
CPU Vcore….……….........................:1.35
CPU Termination…..... 1.200V*.......: <<< Leave
CPU PLL…………………....1.500V*.......: <<< Leave
CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above)
CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above)

MCH/ICH
MCH Core…………….....1.100V...........: <<
MCH Reference….…….0.800V...........; <<< Leave
MCH/DRAM Ref.…......0.900V...........: <<< Leave
ICH I/O……………….....1.550V............: <<< Leave
ICH Core…………...……1.100V............: <<< Leave

DRAM
DRAM Voltage ……....1.800V............:
DRAM Termination .…0.900V............: <<< Leave
Channel A Reference 0.900V............: <<< Leave
Channel B Reference 0.900V............: <<< Leave

Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]

[laker_faker]

Ok so after 3 mins in OCCT critical CPU temperature, on 3,16 Ghz with AC Freezing Pro 7, 69 C. Great. I can change to emo and jump from window:)
Edit:
I setup max temperature in test to 75 so i will tell you results at the morning.
After 20 min max temperature was 70

[Dweirdo]

dude, this temps are huge!!
You are using 1.29v (bios 1.35) this is so weird, is this new pc? u should clean some dirt.

[laker_faker]

Originally Posted by Dweirdo

dude, this temps are huge!!
You are using 1.29v (bios 1.35) this is so weird, is this new pc? u should clean some dirt.

Its new PC, its clean, with good cooler, so i dont know where is problem:/

[BongWizard]

Originally Posted by laker_faker

Its new PC, its clean, with good cooler, so i dont know where is problem:/

did you apply the thermal paste properly? that's usually the reason for high temps when you've got a decent cooler on the CPU... also, you can probably lower the vcore to 1.3V (you really dont need 1.35 when you're at 3.16GHz) and if you can get stable at that voltage you should get much better temps...

next thing i gotta point out is Memory Performance Enhance should always be STANDARD when OCing and set your Static tRead to around 8-11.

but really man if you're getting those kinda temps at stock settings and voltages then you have something physically wrong with your setup... make sure your cooler is seated properly and that you dont have a massive cake of thermal paste on your chip... thermal paste is only to fill tiny gaps which arise from an imperfect finish on the cooler base, the layer should be absolutely tiny, less than paper thin

[Lsdmeasap]

Memory Performance Enhance should always be STANDARD when OCing and set your Static tRead to around 8-11.

For sure

And please set PCI Express to 100, DO IT and stop messing around

You have to set your ram voltage to 2.0-2.1, and add some MCH Voltages

You should also be using the 333 MCH Strap, with 7-8 Static tRead. After 400 FSB use 400 MCH strap and 8-10 Static Tread.

Sounds like you are jumping around FAR too much, and not taking advantage of BIOS profiles. Save on the main Screen of the BIOS if F11, Load is F12

[laker_faker]

Originally Posted by BongWizard

did you apply the thermal paste properly? that's usually the reason for high temps when you've got a decent cooler on the CPU... also, you can probably lower the vcore to 1.3V (you really dont need 1.35 when you're at 3.16GHz) and if you can get stable at that voltage you should get much better temps...

next thing i gotta point out is Memory Performance Enhance should always be STANDARD when OCing and set your Static tRead to around 8-11.

but really man if you're getting those kinda temps at stock settings and voltages then you have something physically wrong with your setup... make sure your cooler is seated properly and that you dont have a massive cake of thermal paste on your chip... thermal paste is only to fill tiny gaps which arise from an imperfect finish on the cooler base, the layer should be absolutely tiny, less than paper thin

Today i bought new thermal paste and use it, just tiny layer. Cooler is 100% correct setuped. i have front and back 120 mm fan so i raly dont know. maybe temperature indicators on motherboard are wrong, tomorrow i will test it with my hand, how hot is it:P

[Lsdmeasap]

Do you maybe have your fans set to low for your cooler, or pointed wrong? What speeds do these fans run, and how are you controlling them?