|
|
|||||||
| GIGABYTE GIGABYTE needs no introduction but they are here to provide free technical support for their motherboards, graphics cards and other products! Competitions will also be ran from time to time! |
 |
|
|
LinkBack | Thread Tools |
Rating: 
|
Display Modes |
05-22-2009, 02:16 AM
|
||||
|
||||
Re: GA-EP45-UD3P - Won't boot with 450FSB
Yes, they replaced the RAM the day after, new one has been fine.
__________________
* CPU: Intel Core 2 Duo E8400 (E0 / 510x8.5 / 4.33GHz) * * Cooler: Thermalright TrUE Black 120 & 2x Noctua NF-P12's (Arctic Cooling MX-2) * * MoBo: Gigabyte GA-EP45-UD3P (Rev. 1.0 - BIOS F10e) * * RAM: Crucial Ballistix Tracer PC2-6400 4GB (4x1GB) - ?-?-?-?? * * GPU: ASUS GeForce 7600GS (512MB) * * HD: Seagate Barracuda 7200.10 SATAII (500GB x6) * * OD: Pioneer DVR112 DVD±RW / Plextor Premium * * PSU: Seasonic M12 - 600W * Last edited by D-an-W; 05-22-2009 at 02:19 AM.     
|
|
05-22-2009, 04:15 AM
|
||||
|
||||
|
Re: GA-EP45-UD3P - Won't boot with 450FSB
You could try a notch up in Vcore from the 24 hour fail, or the same Vcore and a notch up in MCH.
After that try the same Vcore and MCH with more PLL, then more VTT maybe. Be systematic, change one thing at a time. If the thing you changed improved time before failiure, raise it again. If raising makes it worse, lower back and try something else. If raising it again helped, then raise it some more.
__________________
Lian Li PC-A09 Case (Full Aluminium) Corsair HX750 (CWT, 91%(80+ Gold rated @230V) single 62A 12V rail EP45-UD3P v1.0 @ F10e E7400 @ 9.5 x 411, 3.9GHz, 1.425v ??c idle (stuck DTS sensors) and 57c full load (23c ambient) TRUE Black with a single Noctua NF-P12 pumping out 55 CFM @ 19db . 2x2GB Corsair XMS2 PC2-8500, @ 5-5-5-15, 1093-DDR, 2.14v tRead 7 stable 2 x HD4850 512MB @ 715 Core / 2130 Mem. CrossFireX Scythe Musashi twin 100mm fan cooler, 40c Idle and 65C FurMark "Xtreme Burning Mode" Intel X25-M 80GB SSD (OS and Programs) 250MB/s Read 75MB/s Write and WD Caviar Blue 640GB (Storage, Downloads, Temp Files & Folders, Page File etc) Noctua 1300RPM 19dB case fans Dell Ultra Sharp 2209WAf E-IPS @ 1680x1050 This rig loads Windows 7 from the end of AHCI detection to a usable desktop in 13 seconds.  System has passed 24 Hours Prime Blend, 12 hours of both Large and Small FFT and 50 Runs of Intel Burn Test (Maximum Stress) http://valid.canardpc.com/show_oc.php?id=609332 Last edited by Psycho101; 05-22-2009 at 04:18 AM.
|
|
05-22-2009, 04:35 AM
|
|||
|
|||
|
Re: GA-EP45-UD3P - Won't boot with 450FSB
My prime 95 "blend" test with IBT's also thrown in every once in a while BSOD'd @ around 19 or so hours... I have no patience for a 19 hour test failure!! lol
I was testing a FSB @ 495. I thought I was stable to 515.. but I didn't need to go that high so I back it off and wanted to verify long term stability. bzzzzzzzzzzzzt nutz! I am upping my MCH Core to 1.260... where are you at now D-and-W?
__________________
Antec P180 case Intel E8500 E0 Stepping Gigabyte GA-EP45-UD3P rev 1.1 BIOS F10f Thermalright Ultra eXtreme 120!! Do NOT try and save a few bucks with your cooler. Crucial Ballistic PC6400 cas 4 memory 2 x 2G WD Black Edition 640G 32Megs cache 7200RPM XFX Geforce 260/216 Black Edition Corsair TX650W Currently testing 520FSB MCH Core 1.30 & .74 ref, 5-5-5-15, 2.00D (1030 memory) tRD 9, cpu @ 4.16Ghz Running on 64 bit Win 7 RC Build 7100
|
|
05-22-2009, 04:49 AM
|
||||
|
||||
|
Re: GA-EP45-UD3P - Won't boot with 450FSB
I am currently confused as hell with bloody straps B's and D's
The MCH Core is at 1.220V after moving it up one notch... Code:
************************************* ************************************* Gigabyte GA-EP45-UD3P (Rev. 1.0) - F9 ************************************* ************************************* ****************************** MB Intelligent Tweaker(M.I.T.) ****************************** Robust Graphics Booster ..............: [Fast] CPU Clock Ratio ......................: [9X] x Fine CPU Clock Ratio................: +0.0 CPU Frequency ........................: 4.10GHz( 456x9) ********** Clock Chip Control ******** >>>>> Standard Clock Control CPU Host Clock Control................: [Enabled] x CPU Host Frequency(Mhz).............: [456] PCI Express Frequency(Mhz)............: [100] C.I.A.2...............................: [Disabled] >>>>> Advanced Clock Control..........: [Press Enter] CPU Clock Drive.......................: [800mV] PCI Express Clock Drive...............: [900mV] CPU Clock Skew........................: [ 0ps] MCH Clock Skew........................: [ 0ps] ******** DRAM Performance Control ******** Performance Enhance...................: [Standard] Extreme Memory Profile(X.M.P.)........: [Disabled] (G)MCH Frequency Latch................: [Auto] System Memory Multiplier (SPD)........: [2.00D] Memory Frequency(Mhz).....800.........: 912 DRAM Timing Selectable (SPD)..........: [Manual] >>>>> Standard Timing Control x CAS Latency Time................5...: [ 5] x tRCD ...........................5...: [ 4] x tRP.............................5...: [ 4] x tRAS...........................18...: [12] >>>>> Advanced Timing Control.........: [Press Enter] x tRRD............................3...: [ 4] x tWTR............................3...: [ 4] x tWR.............................6...: [ 8] x tRFC...........................52...: [68] x tRTP............................3...: [ 4] x Command Rate (CMD) .............0...: [ 2] >>>>> Channel A Timing Settings.......: [Press Enter] x Static tRead Value.............11...: [ 9] x tRD Phase0 Adjustment...........0...: Auto x tRD Phase1 Adjustment...........0...: Auto x tRD Phase2 Adjustment ..........0...: Auto x tRD Phase3 Adjustment...........0...: Auto x Trd2rd(Different Rank)..........6...: Auto x Twr2wr(Different Rank)..........6...: Auto x Twr2rd(Different Rank)..........5...: Auto x Trd2wr(Same/Diff Rank)..........8...: Auto x DIMM1 Clock Skew Control (ps).......: Auto x DIMM2 Clock Skew Control (ps).......: Auto x DDR Write Training..................: Auto >>>>> Channel A Driving Settings......: [Press Enter] x Driving Strength Profile............: [1066MHz] x Data Driving Pull-Up Level..........: Auto x Cmd Driving Pull-Up level...........: Auto x Ctrl Driving Pull-Up Level..........: Auto x Clk Driving Pull-Up Level...........: Auto x Data Driving Pull-Down Level........: Auto x Cmd Driving Pull-Down level.........: Auto x Ctrl Driving Pull-Down Level........: Auto x Clk Driving Pull-Down Level.........: Auto >>>>> Channel B Timing Settings.......: [Press Enter] x Static tRead Value.............11...: [ 9] x tRD Phase0 Adjustment...........0...: Auto x tRD Phase1 Adjustment...........0...: Auto x tRD Phase2 Adjustment ..........0...: Auto x tRD Phase3 Adjustment...........0...: Auto x Trd2rd(Different Rank)..........6...: Auto x Twr2wr(Different Rank)..........6...: Auto x Twr2rd(Different Rank)..........5...: Auto x Trd2wr(Same/Diff Rank)..........8...: Auto x DIMM1 Clock Skew Control (ps).......: Auto x DIMM2 Clock Skew Control (ps).......: Auto x DDR Write Training..................: Auto >>>>> Channel B Driving Settings......: [Press Enter] x Driving Strength Profile............: [1066MHz] x Data Driving Pull-Up Level..........: Auto x Cmd Driving Pull-Up level...........: Auto x Ctrl Driving Pull-Up Level..........: Auto x Clk Driving Pull-Up Level...........: Auto x Data Driving Pull-Down Level........: Auto x Cmd Driving Pull-Down level.........: Auto x Ctrl Driving Pull-Down Level........: Auto x Clk Driving Pull-Down Level.........: Auto ****** Motherboard Voltage Control ****** Voltage Types..........Normal...........Current ----------------------------------------------- >>> CPU Load-Line Calibration.................: [Disabled] CPU Vcore..............1.27500V.......: [1.31875V] CPU Termination........1.200V.........: [1.280V] CPU PLL................1.500V.........: [1.570V] CPU Reference..........0.760V.........: [0.835V] >>> MCH/ICH MCH Core...............1.100V.........: [1.220V] MCH Reference..........0.760V.........: [0.778V] MCH/DRAM Reference.....0.900V.........: [0.910V] ICH I/O................1.500V.........: [1.590V] ICH Core...............1.100V.........: [1.200V] >>> DRAM DRAM Voltage...........1.800V.........: [2.080V] DRAM Termination.......0.900V.........: [Auto] Channel A Reference....0.900V.........: [Auto] Channel B Reference....0.900V.........: [Auto] ******** Advanced BIOS Features ******** Hard Disk Boot Priority...............: [Press Enter] First Boot Device.....................: [USB-HDD] Second Boot Device....................: [Hard Disk] Third Boot Device.....................: [CDROM] Password Check........................: [Setup] HDD S.M.A.R.T. Capability.............: [Enabled] Limit CPUID Max. to 3.................: [Disabled] No-Execute Memory Protect.............: [Enabled] CPU Enhanced Halt (C1E)...............: [Disabled] C2/C2E State Support..................: [Disabled] x C4/C4E State Support................: Disabled CPU Thermal Monitor 2(TM2) ...........: [Enabled] CPU EIST Function.....................: [Disabled] Virtualization Technology.............: [Disabled] Delay For HDD (Secs)..................: [ 0] Full Screen LOGO Show.................: [Disabled] Init Display First....................: [PEG] ******** Integrated Peripherals ******** USB Keyboard Function.................: [Enabled] USB Mouse Function....................: [Enabled] USB Storage Function..................: [Disabled]
__________________
* CPU: Intel Core 2 Duo E8400 (E0 / 510x8.5 / 4.33GHz) * * Cooler: Thermalright TrUE Black 120 & 2x Noctua NF-P12's (Arctic Cooling MX-2) * * MoBo: Gigabyte GA-EP45-UD3P (Rev. 1.0 - BIOS F10e) * * RAM: Crucial Ballistix Tracer PC2-6400 4GB (4x1GB) - ?-?-?-?? * * GPU: ASUS GeForce 7600GS (512MB) * * HD: Seagate Barracuda 7200.10 SATAII (500GB x6) * * OD: Pioneer DVR112 DVD±RW / Plextor Premium * * PSU: Seasonic M12 - 600W * Last edited by D-an-W; 05-22-2009 at 05:21 AM.
|
|
05-22-2009, 05:57 AM
|
|||
|
|||
|
Re: GA-EP45-UD3P - Won't boot with 450FSB
I have had no luck at all with 2.00B strap. I have had a pretty easy time with 2.00D. I tried for a tRD of 7... bzzzzt. I am now trying for a tRD of 8 @ 450 FSB... and having no luck so far.. My board seems to really like MCH Core being around 1.26.
edit... Don't think I can get tRD of 8 either (Keep locking up on Memtest86+ Test #3).. Guess I will be happy with tRD of 9.
__________________
Antec P180 case Intel E8500 E0 Stepping Gigabyte GA-EP45-UD3P rev 1.1 BIOS F10f Thermalright Ultra eXtreme 120!! Do NOT try and save a few bucks with your cooler. Crucial Ballistic PC6400 cas 4 memory 2 x 2G WD Black Edition 640G 32Megs cache 7200RPM XFX Geforce 260/216 Black Edition Corsair TX650W Currently testing 520FSB MCH Core 1.30 & .74 ref, 5-5-5-15, 2.00D (1030 memory) tRD 9, cpu @ 4.16Ghz Running on 64 bit Win 7 RC Build 7100 Last edited by devoh; 05-22-2009 at 06:14 AM.
|
|
05-22-2009, 02:40 PM
|
||||
|
||||
|
Re: GA-EP45-UD3P - Won't boot with 450FSB
My experience with my E6550 is that up to about 470MHz, the 2.00B strap allows Static tRead Value to be set 1 step lower than the setting required when using the 2.00D strap. At higher cpu clock settings, the 2.00D setting runs fine with Static tRead 1 setting lower (tighter) than the 2.00B strap. I've used both straps up to 520MHz speeds, but both straps are not stable at speeds higher than 494MHz.
Memory bandwidth tests show an improvement of 200+ MHz using the tighter Static tRead setting. I can use identical bios settings with either of these straps when I adjust the Static tRead Value to the lowest possible setting. Some have reported having a more difficult time when using the 2.00B multiplier and they had an easier time using the 2.00D setup. Maybe it's a C2D vs Quad thing. ** edit ** At 459MHz and 2.40B (1102MHz memory), my system is stable using tRD = 8. This means that tRD = 9 is probably required on your system using mid 400MHz speeds with the 2.00D strap. tRD = 9 is usable up to about 510MHz on my system.
__________________
_/\ /\ /\ /\ guru in training (for life) /\ /\ /\ /\_ _______ ~~ we get too soon old and too late smart ~~ E6550 @ 3.444GHz [7x492MHz] ___________________ GeminII down-draft HS w/dual Scythe S-Flex fans EP45-UD3P [rev: 1.0] ~ Bios: F6 __________________ CoolerMaster CM 690 case (RC-690-KKN1-GP) 2x2GB Mushkin XP2-8500 [996599] @5-5-4-12 [1:1] __ Zalman ZM-MFC2 controller, watt meter & temp probes Evga 7600GT video card _________________________ Asus VH242H monitor [1920x1080] Antec EarthWatts PSU (500w) _____________________Logitech Z5500 Digital 5.1 Speakers WD Caviar Black WD6401AALS 640GB ___________.___ win 2000 pro (sp4) <><><> compromise and do it my way <><>   ++ I'm not always right, but I'm never wrong ++. Loading OPTIMIZED bios defaults is REQUIRED before you tweak your bios settings.
This includes new system setups and immediately after flashing your bios!!! Last edited by profJim; 05-22-2009 at 02:47 PM.
|
|
05-22-2009, 03:59 PM
|
||||
|
||||
|
Re: GA-EP45-UD3P - Won't boot with 450FSB
Cheers PJ, I will try and get my head round that tonight.
It didn't like PLL up one notch or CPU Vcore up a notch. Maybe my 24hr Prime was a fluke (Is that even possible?)?
__________________
* CPU: Intel Core 2 Duo E8400 (E0 / 510x8.5 / 4.33GHz) * * Cooler: Thermalright TrUE Black 120 & 2x Noctua NF-P12's (Arctic Cooling MX-2) * * MoBo: Gigabyte GA-EP45-UD3P (Rev. 1.0 - BIOS F10e) * * RAM: Crucial Ballistix Tracer PC2-6400 4GB (4x1GB) - ?-?-?-?? * * GPU: ASUS GeForce 7600GS (512MB) * * HD: Seagate Barracuda 7200.10 SATAII (500GB x6) * * OD: Pioneer DVR112 DVD±RW / Plextor Premium * * PSU: Seasonic M12 - 600W *
|
|
05-22-2009, 09:21 PM
|
|||
|
|||
|
Re: GA-EP45-UD3P - Won't boot with 450FSB
Quote:
Maybe I need to try and go near stock and try a 2.00B strap.. then if I get it slowly move up and see what happens. I really would like to get a 8 tRD.. profJim are you saying that you can go tRD 8 on "B" until like 470 FSB.. then you have to switch over to "D" strap to go above 470 FSB with a 8 tRD? -devoh
__________________
Antec P180 case Intel E8500 E0 Stepping Gigabyte GA-EP45-UD3P rev 1.1 BIOS F10f Thermalright Ultra eXtreme 120!! Do NOT try and save a few bucks with your cooler. Crucial Ballistic PC6400 cas 4 memory 2 x 2G WD Black Edition 640G 32Megs cache 7200RPM XFX Geforce 260/216 Black Edition Corsair TX650W Currently testing 520FSB MCH Core 1.30 & .74 ref, 5-5-5-15, 2.00D (1030 memory) tRD 9, cpu @ 4.16Ghz Running on 64 bit Win 7 RC Build 7100
|
|
05-23-2009, 01:13 AM
|
|||
|
|||
|
Re: GA-EP45-UD3P - Won't boot with 450FSB
**EDIT**
It may be best to ignore my idea... I will not delete it.. so others can comment on how bad of an idea it is.. D-and-W, one of the gang eluded to a GA-EP45-UD3P review with E8400... The guy was using memory that neither one of us could ever afford.. but I noticed something in his review.. he was hitting 4.5Ghz and higher.. it was how he was doing it that facinated me.. I know the guys here don't like auto settings, and for good reason.. but it will give you a quick idea of what the machine thinks will work with what you are asking of it. Then you can tweak from there. I was able to use 2.00B straps to 430 FSB.. then went 2.00D to 450FSB. I think I have the golden 4-4-4-12 tRD of 8 and FSB of 450.. Here is how I found it.. Code:
************************************* ************************************* Gigabyte GA-EP45-UD3P (Rev. 1.1) - F9 ************************************* ************************************* ****************************** MB Intelligent Tweaker(M.I.T.) ****************************** Robust Graphics Booster ..............: [Fast] CPU Clock Ratio ......................: [7X] x Fine CPU Clock Ratio................: +0.0 CPU Frequency ........................: 3.150GHz( 450x7) ********** Clock Chip Control ******** >>>>> Standard Clock Control CPU Host Clock Control................: [Enabled] x CPU Host Frequency(Mhz).............: [450] PCI Express Frequency(Mhz)............: [100] C.I.A.2...............................: [Disabled] >>>>> Advanced Clock Control..........: [Press Enter] CPU Clock Drive.......................: [800mV] PCI Express Clock Drive...............: [900mV] CPU Clock Skew........................: [ 0ps] MCH Clock Skew........................: [ 0ps] ******** DRAM Performance Control ******** Performance Enhance...................: [Standard] Extreme Memory Profile(X.M.P.)........: [Disabled] (G)MCH Frequency Latch................: [Auto] System Memory Multiplier (SPD)........: [2.00D] Memory Frequency(Mhz).....800.........: 900 DRAM Timing Selectable (SPD)..........: [Manual] >>>>> Standard Timing Control x CAS Latency Time................5...: [ 4] x tRCD ...........................5...: [ 4] x tRP.............................5...: [ 4] x tRAS...........................18...: [12] >>>>> Advanced Timing Control.........: [Press Enter] x tRRD............................3...: [AUTO] x tWTR............................3...: [AUTO] x tWR.............................6...: [AUTO] x tRFC...........................52...: [AUTO] x tRTP............................3...: [AUTO] x Command Rate (CMD) .............0...: [AUTO] >>>>> Channel A Timing Settings.......: [Press Enter] x Static tRead Value.............11...: [ 8] x tRD Phase0 Adjustment...........0...: Auto x tRD Phase1 Adjustment...........0...: Auto x tRD Phase2 Adjustment ..........0...: Auto x tRD Phase3 Adjustment...........0...: Auto x Trd2rd(Different Rank)..........6...: Auto x Twr2wr(Different Rank)..........6...: Auto x Twr2rd(Different Rank)..........5...: Auto x Trd2wr(Same/Diff Rank)..........8...: Auto x DIMM1 Clock Skew Control (ps).......: Auto x DIMM2 Clock Skew Control (ps).......: Auto x DDR Write Training..................: Auto >>>>> Channel A Driving Settings......: [Press Enter] x Driving Strength Profile............: [1066MHz] x Data Driving Pull-Up Level..........: Auto x Cmd Driving Pull-Up level...........: Auto x Ctrl Driving Pull-Up Level..........: Auto x Clk Driving Pull-Up Level...........: Auto x Data Driving Pull-Down Level........: Auto x Cmd Driving Pull-Down level.........: Auto x Ctrl Driving Pull-Down Level........: Auto x Clk Driving Pull-Down Level.........: Auto >>>>> Channel B Timing Settings.......: [Press Enter] x Static tRead Value.............11...: [ 8] x tRD Phase0 Adjustment...........0...: Auto x tRD Phase1 Adjustment...........0...: Auto x tRD Phase2 Adjustment ..........0...: Auto x tRD Phase3 Adjustment...........0...: Auto x Trd2rd(Different Rank)..........6...: Auto x Twr2wr(Different Rank)..........6...: Auto x Twr2rd(Different Rank)..........5...: Auto x Trd2wr(Same/Diff Rank)..........8...: Auto x DIMM1 Clock Skew Control (ps).......: Auto x DIMM2 Clock Skew Control (ps).......: Auto x DDR Write Training..................: Auto >>>>> Channel B Driving Settings......: [Press Enter] x Driving Strength Profile............: [1066MHz] x Data Driving Pull-Up Level..........: Auto x Cmd Driving Pull-Up level...........: Auto x Ctrl Driving Pull-Up Level..........: Auto x Clk Driving Pull-Up Level...........: Auto x Data Driving Pull-Down Level........: Auto x Cmd Driving Pull-Down level.........: Auto x Ctrl Driving Pull-Down Level........: Auto x Clk Driving Pull-Down Level.........: Auto ****** Motherboard Voltage Control ****** Voltage Types..........Normal...........Current ----------------------------------------------- >>> CPU Load-Line Calibration.................: [Disabled] CPU Vcore..............1.27500V.......: [AUTO] CPU Termination........1.200V.........: [AUTO] CPU PLL................1.500V.........: [AUTO] CPU Reference..........0.760V.........: [AUTO] >>> MCH/ICH MCH Core...............1.100V.........: [AUTO] MCH Reference..........0.760V.........: [AUTO] MCH/DRAM Reference.....0.900V.........: [AUTO] ICH I/O................1.500V.........: [AUTO] ICH Core...............1.100V.........: [AUTO] >>> DRAM DRAM Voltage...........1.800V.........: [2.000V] DRAM Termination.......0.900V.........: [Auto] Channel A Reference....0.900V.........: [Auto] Channel B Reference....0.900V.........: [Auto] ******** Advanced BIOS Features ******** Hard Disk Boot Priority...............: [Press Enter] First Boot Device.....................: [USB-HDD] Second Boot Device....................: [Hard Disk] Third Boot Device.....................: [CDROM] Password Check........................: [Setup] HDD S.M.A.R.T. Capability.............: [Enabled] Limit CPUID Max. to 3.................: [Disabled] No-Execute Memory Protect.............: [Enabled] CPU Enhanced Halt (C1E)...............: [Disabled] C2/C2E State Support..................: [Disabled] x C4/C4E State Support................: Disabled CPU Thermal Monitor 2(TM2) ...........: [Enabled] CPU EIST Function.....................: [Disabled] Virtualization Technology.............: [Disabled] Delay For HDD (Secs)..................: [ 0] Full Screen LOGO Show.................: [Disabled] Init Display First....................: [PEG] ******** Integrated Peripherals ******** USB Keyboard Function.................: [Enabled] USB Mouse Function....................: [Enabled] USB Storage Function..................: [Disabled] EDIT.. Here is the link to that article. Kick found it http://forum.lowyat.net/topic/861127 -devoh
__________________
Antec P180 case Intel E8500 E0 Stepping Gigabyte GA-EP45-UD3P rev 1.1 BIOS F10f Thermalright Ultra eXtreme 120!! Do NOT try and save a few bucks with your cooler. Crucial Ballistic PC6400 cas 4 memory 2 x 2G WD Black Edition 640G 32Megs cache 7200RPM XFX Geforce 260/216 Black Edition Corsair TX650W Currently testing 520FSB MCH Core 1.30 & .74 ref, 5-5-5-15, 2.00D (1030 memory) tRD 9, cpu @ 4.16Ghz Running on 64 bit Win 7 RC Build 7100 Last edited by devoh; 05-23-2009 at 03:07 AM.
|
|
05-23-2009, 01:26 AM
|
||||
|
||||
|
Re: GA-EP45-UD3P - Won't boot with 450FSB
Quote:
Quote:
Here's a brief summary with my system with cpu speeds above 400MHz: 1) up to about 470MHz, the tRD setting for the B-strap can be 1 step lower (tighter) than the D-strap at the same cpu speeds. 2) higher than 470MHz, the D-strap's tRD setting can be 1 step lower than the B-strap at the same cpu speeds. 3) my system would boot into windows and run all benchmarks up to 528MHz speeds, but always failed stability stress tests above 494MHz, using regardless of which strap was used. 4) above 510MHz, the tRD setting had to be increased, regardless of which strap was used. My system's stability issues are probably due to my E6550 cpu, as the mobo is easily capable of mid to upper 500MHz clock speeds. Anyone care to loan me a cpu that's capable of running at 600MHz? I'd love to run my DDR2 memory 1:1 at 1200MHz. 
__________________
_/\ /\ /\ /\ guru in training (for life) /\ /\ /\ /\_ _______ ~~ we get too soon old and too late smart ~~ E6550 @ 3.444GHz [7x492MHz] ___________________ GeminII down-draft HS w/dual Scythe S-Flex fans EP45-UD3P [rev: 1.0] ~ Bios: F6 __________________ CoolerMaster CM 690 case (RC-690-KKN1-GP) 2x2GB Mushkin XP2-8500 [996599] @5-5-4-12 [1:1] __ Zalman ZM-MFC2 controller, watt meter & temp probes Evga 7600GT video card _________________________ Asus VH242H monitor [1920x1080] Antec EarthWatts PSU (500w) _____________________Logitech Z5500 Digital 5.1 Speakers WD Caviar Black WD6401AALS 640GB ___________.___ win 2000 pro (sp4) <><><> compromise and do it my way <><> ++ I'm not always right, but I'm never wrong ++. Loading OPTIMIZED bios defaults is REQUIRED before you tweak your bios settings.
This includes new system setups and immediately after flashing your bios!!!
|
|
| Bookmarks |
| Currently Active Users Viewing This Thread: 4 (0 members and 4 guests) | |
| Thread Tools | |
| Display Modes | Rate This Thread |
|
|
Linear Mode
