GA-EP45T-UD3LR ......memo problem ?

[saad1957]

i have intel e6850 @1333 default i could manage FSB to 400 , but i can't make memo OCZ Technology | Products | Memory | OCZ PC3-12800 Reaper HPC
run @1600.....................what should I do to make run @1600 .
Now I am running my system @400 FSB and my cpu 400×8 (reduce from 9 because with 9 i get BSOD) @3.2 ghz

[Chike]

Settings problem likely.
Did you overclock manually or with EasyTune?
Read this post for basic settings before attempting OC.
Please post your current BIOS settings using the template in this post.
Add your system specs to your forum signature, with the link to your ram specs.
A screen capture of MemSet main and spd(click spd) windows might be useful too.

[saad1957]

Motherboard: Model:GA-EP45T-UD3LR Rev#: 1 Bios Version : f6b
Cpu Model : Intel E 6850
Ram: OCZ Technology | Products | Memory | OCZ PC3-12800 Reaper HPC
Power Supply Unit: Brand, Model#, Wattage

note: replace all ?? with the value displayed in your bios.
----> Replace "Auto" with manually set values.

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster -------------- : [Auto]
CPU Clock Ratio ---------------------- : [8]
Fine CPU Clock Ratio ----------------- : [0.0] <-- ignore if not available
CPU Frequency ---------------------: 3٫2 <-- this is set by your bios

Clock Chip Control
Standard Clock Control
CPU Host Clock Control --------------- : [Enabled]
CPU Host Frequency (Mhz) --------------: [400]
PCI Express Frequency (Mhz) ---------- : [100] <--- Set to 100, never leave this on Auto

C.I.A.2 ------------------------------ : [Disabled]

Advanced Clock Control ------- [Press Enter]
CPU Clock Drive ---------------------- : [800]
PCI Express Clock Drive -------------- : [900]
CPU Clock Skew (ps) ------------------ : [0]
MCH Clock Skew (ps) ------------------ : [0]

DRAM Performance Control
Performance Enhance ------------------- : [STD] <--- set to STANDARD when overclocking
Extreme Memory Profile --- (X.M.P.) --- : [Disabled] <--- Leave this Disabled
(G)MCH Frequency Latch ---------------- : [Auto]
System Memory Multiplier -------------- : [3٫33] <-- this is the setting that you are using
Memory Frequency (Mhz) ---------------- : [1333]
DRAM Timing Selectable ---------------- : [Auto] <-- set to MANUAL for overclocking

Standard Timing Control
CAS Latency Time -------- 7 ---------- : [Auto]
tRCD -------------------7 ---------- : [Auto]
tRP --------------------- 7---------- : [Auto]
tRAS ------------------20 ---------- : [Auto]

rest of setting is default

[Chike]

Default or not, please post full settings, can't tell if default is auto or set manually.

Disabling XMP require DRAM Voltage to be set manually to it's specified value for DDR-1600, what is BIOS PC Health Status reading for memory voltage?

Leaving some of the voltage setting on auto while OCing might set them dangarousely high, or at least higher than actually needed.

Please post a screen capture of EasyTune -> Tuner -> Advanced -> Voltage tab in addition to MemSet screen capture.

[saad1957]

in bios ...Vcore = 1.3 DDR15V = 1.808
Attachment 1746

[saad1957]

more

[saad1957]

sorry.........i don't know how to send multi images in one reply so one by one

[saad1957]

last

[Chike]

The ET6 advanced voltage tab please, not frequency, and MemSet ppd(click spd) window too.

Now I am realy confused. Your ram clock is 750(DDR-1500) with 3:5 ration which indicates 450FSB and not 400. And memory voltage set to 1.8v, auto or manually?

In order to be able to advise you, we need the exact details and what you are trying to do and what fails.

[Chike]

Maybe MemSet is displating the wrong memory clock, could you post CPU-Z memory tab too?