Overclocking EP45-UD3P and Q6600 G0

[soulz9]

Originally Posted by fatguy1992

Heres my 3.6GHz, well with more Vcore cause I can run stock Vcore for 3.6GHz

MB Intelligent Tweaker(M.I.T.)

Robust Graphics Booster ...............: Auto
CPU Clock Ratio ..........................: 9
CPU Frequency ...........................: 3.60 (400*9)

Clock Chip Control

Standard Clock Control

CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 400 Mhz
PCI Express Frequency (Mhz) .........:100
C.I.A.2 .................................:[Disabled]

Advanced Clock Control [Press Enter]

CPU Clock Drive...........................: 700mv
PCI Express Clock Drive.................: 700mv
CPU Clock Skew (ps)....................: 0 ps
MCH Clock Skew (ps)...................: 0 ps

DRAM Performance Control

Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: 400MHz
System Memory Multiplier ..............: 2.00D
Memory Frequency (Mhz) ..............: 800
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time........................ 5
tRCD ......................................... 5
tRP'........................................... 5
tRAS.......................................... 15

Advanced Timing Control

tRRD........................................... Auto
tWTR.......................................... Auto
tWR............................................ Auto
tRFC........................................... Auto
tRTP........................................... Auto
Command Rate (CMD) ....................: Auto

Driving Strength Profiles

Driving Strength ............................800

Channel A
Static tRead Value.........................: 8
tRD Phase0 Adjustment...................: Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Channel B
Static tRead Value.........................: 8
tRD Phase0 Adjustment...................: Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Motherboard Voltage Control

CPU
LLC............................................: Enabled
CPU Vcore….……….........................: 1.45v
CPU Termination…..... 1.200V*.......: 1.30v
CPU PLL…………………....1.500V*.......: 1.5v
CPU Referen.…………....0.755V*.......: 0.863v

MCH/ICH
MCH Core…………….....1.100V...........: 1.2v
MCH Reference….…….0.760V...........: 0.803v upto 0.863v
MCH/DRAM Ref.…......0.900V...........: 1.0v
ICH I/O……………….....1.550V............: 1.57v
ICH Core…………...……1.100V............: 1.1v

DRAM
DRAM Voltage ……....1.800V............: 2.0v
DRAM Termination .…0.900V............: 1.0v
Channel A Reference 0.900V............: 1.0v
Channel B Reference 0.900V............: 1.0v

Advanced Settings

Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Disabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]

I hope that helps, but every CPU is different.

Originally Posted by Chike

What coller do you have, under what load and ambiant temperature you had those temps?
Maybe you don't need all that vcore, what is your CPU VID?

I have the Sunbeamtech Core-Contact Feeezer. Here's the thing I've set my vcore at 1.48v in Bios it booted fine, but when I ran LinX or IBT it failed. In addition, at 1.48v I was getting very high temps to around 85 C.
My CPU ID showed Core voltage of 1.44 or it was around 1.45V.

Do you think I should try to re-apply Shin Etsu? The Core Temp shows VID of 1.3000v.

I got it OC'd stable at 8x400 FSB gave me 3.2Ghz running it @ 1000 Mhz 2.2V
Vcore was set to 1.3625V and Everest showing Core voltage of 1.25-1.31V.

And my temps are max 67C on full load while running IBT on 5 runs with Maximum Stress level. Which passed. Any suggestions on if I can get it stable at 3.6Ghz 400x9 FSB would be nice.

[Chike]

Cooler seems to be solid but I am not familiar with the Shin Etsu, is it any good?
At 3.6GHz my E7200 get to 73c at 32 ambiant and it hs only 2 cores so it may be you'd have to sattle for a bit less than 3.6GHz 3.4 or 3.5.
I also hear not al Q6600 can do 3.6GHz.
I suggest you make your own thread, post your settings using the template from this post, add your system specs to your forum signature including a link to your ram specs, and people will be able to advise.

[soulz9]

Originally Posted by Chike

Cooler seems to be solid but I am not familiar with the Shin Etsu, is it any good?
At 3.6GHz my E7200 get to 73c at 32 ambiant and it hs only 2 cores so it may be you'd have to sattle for a bit less than 3.6GHz 3.4 or 3.5.
I also hear not al Q6600 can do 3.6GHz.
I suggest you make your own thread, post your settings using the template from this post, add your system specs to your forum signature including a link to your ram specs, and people will be able to advise.

From comparison Shin Etsu tends to get the best temps over a period of time, if you perform the burn in period of 200 Hours. I guess I'll stick with 3.2 Ghz, I don't really need the extra mhz, but it would be nice to achieve it. Thanks alot anyways.