OverClocking Q6600 in GA-EP45-DS4P F8 Guide Me

[Nickel020]

when i had P31 i overclocked it by
different RAMs (valueram) and it was stabble

I see, the fist screenshot is the P31 board.

Are settings in that second screenshot 100% stable? Have you tried Prime 95 at those settings? If they're stable I can discard the RAM itself being the problem, as it's obviously capable of running stable on this board.

[kovaxo]

after running the test am 100% its not RAMS problem
its bios

[Nickel020]

Could you post the BIOS template again please with the settings as I told you? I'm getting confused as to what we've already tried.

[kovaxo]

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster .................: [Auto]
CPU Clock Ratio ............................: [9x]
CPU Frequency .............................: 3.00GHz [333 x 9]

Clock Chip Control
Standard Clock Control
CPU Host Clock Control......................: [Enabled]
CPU Host Frequency (Mhz) ................: [333]
PCI Express Frequency (Mhz) .............: 100
C.I.A.2 ..........................................: [Disabled]

Advanced Clock Control [Press Enter]
CPU Clock Drive............................: [800mV]
PCI Express Clock Drive..................: [900mV]
CPU Clock Skew (ps).....................: [ 0 ps] What this use for ?
MCH Clock Skew (ps).....................: [0 ps] What this use for ?

DRAM Performance Control
Performance Enhance........................: [Standard]
(G)MCH Frequency Latch....................: [333]
System Memory Multiplier ..................: [3.20B]
Memory Frequency (Mhz) ...............: 1066
DRAM Timing Selectable ..................: [Manual]

Standard Timing Control
CAS Latency Time....................... [7]
tRCD ........................................ [7]
tRP'.......................................... [7]
tRAS....................................... [20]

Advanced Timing Control
tRRD................................... [7]
tWTR................................... [Auto]
tWR.................................... [Auto]
tRFC................................... [Auto]
tRTP................................... [Auto]
Command Rate (CMD) ....................[Auto]




Driving Strength Profiles
Driving Strength .........................[1066]


Channel A
Static tRead Value..................... [Auto]
tRD Phase0 Adjustment.................. [Auto]
tRD Phase1 Adjustment.................. [Auto]
tRD Phase2 Adjustment ................. [Auto]
tRD Phase3 Adjustment.................. [Auto]
Trd2rd(Different Rank)................. [Auto]
Twr2wr(Different Rank)................. [Auto]
Twr2rd(Different Rank)................. [Auto]
Trd2wr(Same/Diff Rank)................. [Auto]
Dimm1 Clock Skew Control............... [Auto]
Dimm2 Clock Skew Control............... [Auto]
DDR Write Training..................... [Auto]

Channel B
Static tRead Value..................... [Auto]
tRD Phase0 Adjustment.................. [Auto]
tRD Phase1 Adjustment.................. [Auto]
tRD Phase2 Adjustment ................. [Auto]
tRD Phase3 Adjustment.................. [Auto]
Trd2rd(Different Rank)................. [Auto]
Twr2wr(Different Rank)................. [Auto]
Twr2rd(Different Rank)................. [Auto]
Trd2wr(Same/Diff Rank)................. [Auto]
Dimm1 Clock Skew Control............... [Auto]
Dimm2 Clock Skew Control............... [Auto]
DDR Write Training.....................[Auto]



Motherboard Voltage Control
Voltage Type Normal Current
CPU Vcore........................ 1.325V [Auto]
CPU Termination.................. [auto]
CPU PLL............................. 1.500V [1.500V]
CPU Referen........................ 0.760V [Auto]



MCH/ICH
MCH Core........................... 1.100V [Auto]
MCH Reference.................... 0.760V [Auto]
MCH/DRAM Ref..................... 0.900V [Auto]
ICH I/O........................... 1.500V [Auto]
ICH Core......................... 1.100V [Auto]
DRAM
DRAM Voltage..................... 1.800V [2.00V]
DRAM Termination................. 0.900V [Auto]
Channel A Reference ............. 0.900V [Auto]
Channel B Reference ............. 0.900V [Auto]




its working great at this setting

[Nickel020]

Look here for eplanations of the BIOS settings:
Gigabyte X48T DQ6 Living Review - Page 2 - Clunk's Forums.

Keep the RAM at 2.0D for the time being, you can always raise it later when the CPU is stable.

Try FSB 400, memory 2.0D, VCore 1.45V, loadline calibration on, PLL at 1.7V, MCH Core at 1.24V and CPU Termination at 1.4V. If that doesn't work raise CPU Temrination to 1.45V and see if that helps

[kovaxo]

any one ?

[Nickel020]

Why "anyone?", the BIOS settings are all explained in the link I gave. If you don't understand something there you need to tell us^^

[kovaxo]

all i need is right Voltage to set from A to Y
i mean every voltage in motherboard to hit 3.6 Mhz ++

[Nickel020]

You should have asked about that then ;)

There are no "right" voltages though, every CPU is different. My guess is that you will need about 1.4-1.45V "real" voltage (as read by CPU-z) under load. Set the FSb to 400.
Run the RAM at 2.0D first though.

[Lsdmeasap]

Still need help? All those settings in Auto is likely a large part of your issues