Gigabyte GA-P35-DS3 boot problems!

[Lsdmeasap]

Is your hard drive with windows on it SATA or IDE?

Do not worry about the MIT page until you can at least boot into windows. Although I would go in there and set the RAM (DDR voltage) to what is specified by your ram sticks. 1.8 is the starting voltage If you ram is 2.0 add +.2, 2.1 add +.3...If it says 1.8 leave on Auto

YOu never answered me about your BOOT section, and where you have your hard drives plugged into.

I really think we need a better translator, as I cant get what you mean often and I dont think you listen to half of the things I suggest. Do you know anyone who can speak english to better help me talk with you? We can surely solve this in a few minutes if we both spoke the same language

The MIT settings I posted to you are the same on our systems, maybe one or 2 is missing, but the ones I posted are just like that because they are all manually set. Which Is what I suggest you do after we get your advanced BIOS section fixed with your hard drives. Did you fix the Boot order, and the first, second and third boot device like I said?

This is what I would suggest you set your MIT to FOR NOW, you can change it to better or back to auto later. I need to know the exact number and speed 4on your ram so I can tell you what voltages to run

USE THESE SETTINGS FOR NOW

*NOTE*

None of this is going to help until you fix the hard drives section I posted about on page 2

Robust Graphics Booster___________ [Auto]
CPU Clock Ratio ____________ [10]
CPU Host Clock Control_ [Enabled]
CPU Host Frequency (MHz)__________ [200]
PCI Express Frequency (Mhz)_______ [100]
C.I.A. 2__________________________ [Disabled]
System Memory Multiplier (SPD)____ [4.00]
DRAM Timing Selectable_______ SPD __ [Manual]

CAS Latency Time_____________ 5
Dram RAS# to CAS# Delay______ 5
Dram RAS# Precharge Delay_____5
Precharge Delay (tRAS)________18
ACT to ACT Delay (tRRD)_______Auto
Rank Write to READ Delay______Auto
Write to Precharge Delay______Auto
Refresh to ACT Delay________42
Read to Precharge Delay_______Auto
Static tRead Value_______________ Auto Or 10
Static tRead Phase Adjust________ Auto

System Voltage Control____ [Manual]
DDR2 OverVoltage Control__ [+0.300V] +.3=2.1v +.2=2.0v +.1=1.9 Use what your ram says on the package or stick

PCI-E OverVoltage Control_ [+0.1V]
FSB OverVoltage Control___ [+0.1V]
(G)MCH OverVoltage Control [+0.1V]
CPU Voltage Control_______ [1.25]<<< you need/should set to what your CPU has for default under this line or on the box or in coretemp for VID

But AGAIN, you HAVE to get the sections about the hard drives and boot order fixed first.

So tell me IDE or SATA hard drives, where you plug them in at and if you fixed the Boot order part of advanced BIOS (Your hard drive needs to be first in the list use + key to move it to the top once the window opens for HARD DISK BOOT PRIORITY.

[slate]

first of all big thx to you for your patience, its ok i can understand allmost all what you say, my problem is to tell you what i want :) dont know eng so good :)


About HD

my Hard Drive is WD250aaks,16mb baffer, on SATA! i cant remanber for 100 % where i plug it in but i think its on orange sata connector.

yes yes yes i setup first, secend, 3rd boot device.. like you say..
i setup HD to be on 1st place in option that you say.. i did all that things..

WORST ! problems in all that is , that i cant look changes eazy to see is that works, to know is problems fixed!
becouse that problems are not allways, i can start computer 20 times and all will go fine .. with no single problems.. but for example it can make problem 21st time when i start it

and one more thing i ask local support for my problems and man aks me do i have some usb device connected to my computer on start i say that i have just my mouse that is usb( Logitec mx510 ) and that man say " try to connect your mouse to PS2 connector with usb/ps2 connector and i did it now i wait for problems to show up again :)

so what you think can that be a problem ?

[Lsdmeasap]

Yes that can be a issue. Do that use a usb to ps2 connector for your mouse and disable "Legacy Usb Storage Detect" And disbable "USB Mouse and Keyboard" support. I use a USB mouse with PS2 adapter and I actually use USB keyboard but still have that disabled and it works fine.

Here is a pic of my BIOS, and I use USB keyboard, USB mouse (With PS2 adapter) and have no issues. I do have legacy disabled as well, I just had it on for this pic to show someone else something.



No problem about helping, Wish We could speak the same it would make things easier.

And just so you know sometimes also what may cause that to only happen like you say sometimes is having everything on AUTO, sometimes auto is too much or not enough of one thing. I always say it is best to manually set everything even if you are not going to overclock.

Also do you have a good power supply? Sometimes if not that can be the cause of strange errors as well

[slate]

ok ok i will disable it

i have Godegen bizza 6099-ca. his power i use and in windows i got no problems at all ! computer works 12 h and no single problem just damn turning on 1 time of 20 times or normal booting

[Lsdmeasap]

Yeah, well that could be anything with your other timings being all on auto. I do suggest manually setting everything, but since you did not have those things disabled before that may solve all your problems now.

So with all those 3 things disabled wait a week or so and see if after 20 or so reboots it is all working because that may just fix all your problems.

I also suggest do not use sleep or resume it also will cause issues

I have never heard of that power supply is it a good brand?

[slate]

[Lsdmeasap]

[slate]

its 2 3 day i dont have problems yet ... we will see ..

[Lsdmeasap]

Looking good!