GIGABYTE Latest Beta BIOS

[amorak]

Any comments on what the F17a BIOS for the Z77-D3H provides?

[stasio]

Satsio, I owe you a Beer!

See what F9q did for my UD5H over at ***Official***Z77X-D3H UD3H UD5H Discussion\Owners Club***

OK bro,nice to see your mouse working.

What is changed in F10A for GA-Z77M-D3H?

I don't get why there aren't any changelogs for these BETA bios versions.

what's new for the z77x-ud3h??

Any comments on what the F17a BIOS for the Z77-D3H provides?

As for the rest of BIOS's specific for each board, minor tweaks done also.

[basschilperoord]

OK bro,nice to see your mouse working.





As for the rest of BIOS's specific for each board, minor tweaks done also.

Thank you stasio.

Problem still occurs with my WUSB300N, I get slow boots when I plug it in.

[stasio]

Thank you stasio.

Problem still occurs with my WUSB300N, I get slow boots when I plug it in.

Yea,I read this.
As your problem is very specific,ask GGTS for help or advice.
Hope,you try each USB ports and had latest drivers installed.

[VimesUK]

Is there any chance of letting the powers that be know that on occasion both my USB 2 and 3 front ports (only) will not respond after being in S3 sleep mode. This is on my Z77x UD5H board. I have just flashed it to the latest BIOS so I will need to test that for longer to confirm. Everything else seems to work a treat but the front USB port can, at times, be iffy when resumed from sleep whilst other times they awake without issue.
As I use the sleep function all the time (Windows 7 x64 Home) I will only notice the port situation when I plug a stick or drive into it and thus it will then need a reboot to sort it out, which it always does.

Thanks :)

[Octopuss]

Has there ever been reported bad functionality of F_USB30 "doubleport" on Z77X-UD3H? I connected appropriate bay with two USB3 ports to that but only one of them work. I can't tell what's wrong...

[VimesUK]

When I had the Z77 D3H only the front left USB 3 port would work with my Toshiba 1TB USB 3 hard drive. The right one would only show it as needing to format (after doing so it would say it needed it again) or it would not show it at all. Both ports would work fine with my card reader and any stick. They would also work fine with my USB 2 hard drives.

On my UD5H board both front USB 3 ports will work fine with that HD.

Both boards will have issues with the front ports on occasion not waking up from sleep.

Latest drivers used for each board.

I have noted in other forums of similar issues with the front ports.

[Octopuss]

In my case the right port works fine and left is completely dead. I can't test this at all cause I don't have other front panel, and you can only plug that double connector in that port too.

[irfs]

Bios f9q DRAM voltage issue. (prev beta F9 had similar issue)

Correctly sets 1.35v for samsung green. But can not increase voltage. My Backup bios is F8 when i set 1.4v then switch off flip switch to Main bios (F9q) it then sets 1.4v. It seems F9q is using the voltage settings from Backup bios.

[dopus]

gigabyte z68x-ud3h-b3 with the latest uefi bios from this site. Usb3 ports are not working. The usb 3 controller get detected by windows and the latest eton usb3 drivers are installed (112) but when I try the port with my headset or a memory stick the ports detects nothing. I hope this will be fixed in next bios.