Well after a 12mnth pause I woke up and felt like my 920 needed a good old fashion beating.... so once again embarked upon an OC journey.. being that this is already my 2nd 920 having blown the 1st one upon (scorch marks etc between contacts).. this has been something long in the making.
IDLES@40 / OCCT Medium 10 Minute Run 60
So to start off with... I'll decrease the bclk from 200 back to 150 and start increasing the cpu multi.
Settings:
Advanced CPU Features:[/B] CPU Clock Ratio ................................ [15x]
Intel(R) Turbo Boost Tech ..................[Enabled]
CPU Cores Enabled ............................ [All]
CPU Multi Threading .......................... [Enabled]
CPU Enhanced Halt (C1E) ................... [Disabled]
C3/C6/C7 State Support .................... [Disabled]
CPU Thermal Monitor ......................... [Enabled]
CPU EIST Function ............................ [Disabled]
Virtualization Technology ................... [Disabled] << Disabled if you do not use Vmware or Virtual PC Programs
Bi-Directional PROCHOT ..................... [Enabled]
Uncore & QPI Features:
QPI Link Speed .............................. x36
Uncore Frequency .......................... x16 - (Always 2x memory Multi or 2x +1)
Isonchronous Frequency ..................[Enabled]
Standard Clock Control:Base Clock (BCLK) Control ................ [Enabled]
BCLK Frequency (MHz) ..................... 200
PCI Express Frequency (MHz) ........... [100]
Advanced Clock Control:
CPU Clock Drive ..............................[800mV]
PCI Express Clock Drive ................... [900mV]
CPU Clock Skew ............................. [0ps]
IOH Clock Skew ............................. [0ps]
Advanced DRAM Features:
Performance Enhance ...................... [Standard]
Extreme Memory Profile (X.M.P) ......... [Profile1] - Added this to get my XMS1866 to run at correct voltage etc
System Memory Multiplier (SPD) ........ 6
DRAM Timing Selectable (SPD) .......... [From profile]
Channel A + B + C Channel A Timing Settings:
##Channel A Standard Timing Control##
CAS Latency Time ......................
tRCD .......................................
tRP .........................................
tRAS .......................................
##Channel A Advanced Timing Control##
tRC ........................................ (Should be = tRAS + tRP or above for stability)
tRRD .......................................
tWTR ...................................... (Must be Write to Read Delay/Same Rank - (tWL + 4)
tWR ........................................
tWTP ....................................... (tWTP Must = tWR + tWL + 4)
tWL ........................................ (tWL Must be CAS Latency -1)
tRFC .......................................
tRTP .......................................
tFAW ......................................
Command Rate (CMD) ................
##Channel A Misc Timing Control##
Round Trip Latency ...................
B2B CAS Delay ..........................
Advanced Voltage Control:
CPU Load Line Calibration ................. [Level 1]
CPU Vcore ............................... 1.0375v
DVID .................................... 0.2100v - Above bclk of 170 need to increase vcore to prevent 0x124 BSOD
QPI/VTT Voltage 1.150v ............ 1.3000v - Wouldn't boot at bclk 200 without 1.3
CPU PLL 1.800v ....................... 1.800v
MCH/ICH:
PCIE 1.500v ........................... 1.5v
QPI PLL 1.100v ....................... 1.1v
IOH Core 1.100v ..................... 1.1v
ICH I/O 1.500v ....................... 1.5v
ICH Core 1.1v ........................ 1.1v
DRAM:
DRAM Voltage 1.500v .............. 1.66v - [Profile1]
DRAM Termination 0.750v [AUTO]
Ch-A Data VRef. 0.750v [AUTO]
Ch-B Data VRef. 0.750v [AUTO]
Ch-C Data VRef. 0.750v [AUTO]
Ch-A Address VRef. 0.750v [AUTO]
Ch-B Address VRef. 0.750v [AUTO]
Ch-C Address VRef. 0.750v [AUTO]
IDLES@40 / OCCT Medium 10 Minute Run 60
So to start off with... I'll decrease the bclk from 200 back to 150 and start increasing the cpu multi.
Settings:
Advanced CPU Features:[/B] CPU Clock Ratio ................................ [15x]
Intel(R) Turbo Boost Tech ..................[Enabled]
CPU Cores Enabled ............................ [All]
CPU Multi Threading .......................... [Enabled]
CPU Enhanced Halt (C1E) ................... [Disabled]
C3/C6/C7 State Support .................... [Disabled]
CPU Thermal Monitor ......................... [Enabled]
CPU EIST Function ............................ [Disabled]
Virtualization Technology ................... [Disabled] << Disabled if you do not use Vmware or Virtual PC Programs
Bi-Directional PROCHOT ..................... [Enabled]
Uncore & QPI Features:
QPI Link Speed .............................. x36
Uncore Frequency .......................... x16 - (Always 2x memory Multi or 2x +1)
Isonchronous Frequency ..................[Enabled]
Standard Clock Control:Base Clock (BCLK) Control ................ [Enabled]
BCLK Frequency (MHz) ..................... 200
PCI Express Frequency (MHz) ........... [100]
Advanced Clock Control:
CPU Clock Drive ..............................[800mV]
PCI Express Clock Drive ................... [900mV]
CPU Clock Skew ............................. [0ps]
IOH Clock Skew ............................. [0ps]
Advanced DRAM Features:
Performance Enhance ...................... [Standard]
Extreme Memory Profile (X.M.P) ......... [Profile1] - Added this to get my XMS1866 to run at correct voltage etc
System Memory Multiplier (SPD) ........ 6
DRAM Timing Selectable (SPD) .......... [From profile]
Channel A + B + C Channel A Timing Settings:
##Channel A Standard Timing Control##
CAS Latency Time ......................
tRCD .......................................
tRP .........................................
tRAS .......................................
##Channel A Advanced Timing Control##
tRC ........................................ (Should be = tRAS + tRP or above for stability)
tRRD .......................................
tWTR ...................................... (Must be Write to Read Delay/Same Rank - (tWL + 4)
tWR ........................................
tWTP ....................................... (tWTP Must = tWR + tWL + 4)
tWL ........................................ (tWL Must be CAS Latency -1)
tRFC .......................................
tRTP .......................................
tFAW ......................................
Command Rate (CMD) ................
##Channel A Misc Timing Control##
Round Trip Latency ...................
B2B CAS Delay ..........................
Advanced Voltage Control:
CPU Load Line Calibration ................. [Level 1]
CPU Vcore ............................... 1.0375v
DVID .................................... 0.2100v - Above bclk of 170 need to increase vcore to prevent 0x124 BSOD
QPI/VTT Voltage 1.150v ............ 1.3000v - Wouldn't boot at bclk 200 without 1.3
CPU PLL 1.800v ....................... 1.800v
MCH/ICH:
PCIE 1.500v ........................... 1.5v
QPI PLL 1.100v ....................... 1.1v
IOH Core 1.100v ..................... 1.1v
ICH I/O 1.500v ....................... 1.5v
ICH Core 1.1v ........................ 1.1v
DRAM:
DRAM Voltage 1.500v .............. 1.66v - [Profile1]
DRAM Termination 0.750v [AUTO]
Ch-A Data VRef. 0.750v [AUTO]
Ch-B Data VRef. 0.750v [AUTO]
Ch-C Data VRef. 0.750v [AUTO]
Ch-A Address VRef. 0.750v [AUTO]
Ch-B Address VRef. 0.750v [AUTO]
Ch-C Address VRef. 0.750v [AUTO]
Comment