Hi all. Its time for my ram upgrade and i need your help again :D
pc specs are gigabyte ex58 ud5, ati hd5850 , 920 i7
My previous ram was ocz plattinum ocz3p2000lv6gk 3x2gb but one module died 2 days ago
Today i order Sniper - F3-12800CL9T-12GBSR2 - G.SKILL DDR3 Memory (still time to cancel my order if.... :D)
Do you think its good upgrade?
Now to the point. I read somewhere that i might have a problem with VTT (and i might fry the cpu???) because those g.skills running on low voltage 1.25v.
My previous oc settings is below. i hope you can tell me what modifications shall i do when i install the new ram
CPU Clock Ratio ................................ [19x] 3.8 (200x19)
Intel(R) Turbo Boost Tech .................. [Enabled]
CPU Cores Enabled ............................ [All]
CPU Multi Threading .......................... [Enabled]
CPU Enhanced Halt (C1E) ................... [Disabled]
C3/C6/C7 State Support .................... [Enabled]
CPU Thermal Monitor ......................... [Enabled]
CPU EIST Function ............................ [Enabled]
Bi-Directional PROCHOT ..................... [Enabled]
Virtualization Technology ................... [Disabled]
Uncore & QPI Features:
QPI Link Speed .............................. [7.2 GHz] (x36 clock Ratio)
Uncore Frequency .......................... [3200 MHz] ( x16 Uncore Clock Ratio)
Isonchronous Frequency .................. [Enabled]
Standard Clock Control:
Base Clock (BCLK) Control ................ [Enabled]
BCLK Frequency (MHz) ..................... [200]
PCI Express Frequency (MHz) ........... [100]
C.I.A.2 [Disabled]
Advanced Clock Control:
CPU Clock Drive .............................. [800 mV]
PCI Express Clock Drive ................... [900 mV]
CPU Clock Skew ............................. [0ps]
IOH Clock Skew ............................. [0ps]
Advanced DRAM Features:
Performance Enhance ...................... [Standard]
System Memory Multiplier (SPD) ........ [x8]
DRAM Timing Selectable (SPD) .......... [Quick]
Channel A + B + C
Channel A Timing Settings:
##Channel A Standard Timing Control##
CAS Latency Time ...................... [ 8 ]
tRCD ....................................... [ 8 ]
tRP ......................................... [ 8 ]
tRAS ....................................... [24]
Command Rate (CMD) ........... [ 1 ]
Memory Frequency ............... [1600 MHz]
Advanced Voltage Control:
CPU
Load Line Calibration ................. [Enabled]
CPU Vcore ....................1.23125v [Normal]
Dynamic Vcore(DVID)..+0.00000V [ -0.03125V]
QPI/VTT Voltage ..................... [1.300V]
CPU PLL .................................. [1.800V]
MCH/ICH
PCIE 1.500v ........................... [Auto]
QPI PLL 1.100v ....................... [Auto]
IOH Core 1.100v ..................... [1.24V]
ICH I/O 1.500v ....................... [Auto]
ICH Core 1.1v ........................ [Auto]
DRAM
DRAM Voltage........................ 1.600v
All other settings [AUTO]
If you need more details please tell me so i can add them
pc specs are gigabyte ex58 ud5, ati hd5850 , 920 i7
My previous ram was ocz plattinum ocz3p2000lv6gk 3x2gb but one module died 2 days ago
Today i order Sniper - F3-12800CL9T-12GBSR2 - G.SKILL DDR3 Memory (still time to cancel my order if.... :D)
Do you think its good upgrade?
Now to the point. I read somewhere that i might have a problem with VTT (and i might fry the cpu???) because those g.skills running on low voltage 1.25v.
My previous oc settings is below. i hope you can tell me what modifications shall i do when i install the new ram
CPU Clock Ratio ................................ [19x] 3.8 (200x19)
Intel(R) Turbo Boost Tech .................. [Enabled]
CPU Cores Enabled ............................ [All]
CPU Multi Threading .......................... [Enabled]
CPU Enhanced Halt (C1E) ................... [Disabled]
C3/C6/C7 State Support .................... [Enabled]
CPU Thermal Monitor ......................... [Enabled]
CPU EIST Function ............................ [Enabled]
Bi-Directional PROCHOT ..................... [Enabled]
Virtualization Technology ................... [Disabled]
Uncore & QPI Features:
QPI Link Speed .............................. [7.2 GHz] (x36 clock Ratio)
Uncore Frequency .......................... [3200 MHz] ( x16 Uncore Clock Ratio)
Isonchronous Frequency .................. [Enabled]
Standard Clock Control:
Base Clock (BCLK) Control ................ [Enabled]
BCLK Frequency (MHz) ..................... [200]
PCI Express Frequency (MHz) ........... [100]
C.I.A.2 [Disabled]
Advanced Clock Control:
CPU Clock Drive .............................. [800 mV]
PCI Express Clock Drive ................... [900 mV]
CPU Clock Skew ............................. [0ps]
IOH Clock Skew ............................. [0ps]
Advanced DRAM Features:
Performance Enhance ...................... [Standard]
System Memory Multiplier (SPD) ........ [x8]
DRAM Timing Selectable (SPD) .......... [Quick]
Channel A + B + C
Channel A Timing Settings:
##Channel A Standard Timing Control##
CAS Latency Time ...................... [ 8 ]
tRCD ....................................... [ 8 ]
tRP ......................................... [ 8 ]
tRAS ....................................... [24]
Command Rate (CMD) ........... [ 1 ]
Memory Frequency ............... [1600 MHz]
Advanced Voltage Control:
CPU
Load Line Calibration ................. [Enabled]
CPU Vcore ....................1.23125v [Normal]
Dynamic Vcore(DVID)..+0.00000V [ -0.03125V]
QPI/VTT Voltage ..................... [1.300V]
CPU PLL .................................. [1.800V]
MCH/ICH
PCIE 1.500v ........................... [Auto]
QPI PLL 1.100v ....................... [Auto]
IOH Core 1.100v ..................... [1.24V]
ICH I/O 1.500v ....................... [Auto]
ICH Core 1.1v ........................ [Auto]
DRAM
DRAM Voltage........................ 1.600v
All other settings [AUTO]
If you need more details please tell me so i can add them
Comment