Announcement

**Lsdmeasap** · 08-24-2008, 11:14 PM

Re: (EP45-DS3R) What would be a good setting to come to DDR2-1200?

Please post your Full specs and what speed you are running your CPU at, and I can better help you

**gugle** · 08-25-2008, 12:05 AM

Re: (EP45-DS3R) What would be a good setting to come to DDR2-1200?

Originally posted by Lsdmeasap View Post

Please post your Full specs and what speed you are running your CPU at, and I can better help you

want to 3600 (450x) | DDR2-1200

is

Q6600 (400x8)
Transcend AxeRam DDR2-800 @ 1066

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: [Auto]
CPU Clock Ratio ..........................: 8
CPU Frequency ...........................: 3200

Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 400
PCI Express Frequency (Mhz) .........:Set to 100

Advanced Clock Control [Press Enter] (copied from another topic)
CPU Clock Drive...........................: 800
PCI Express Clock Drive.................: 900
CPU Clock Skew (ps)....................: [Auto]
MCH Clock Skew (ps)...................: [Auto]

DRAM Performance Control
Performance Enhance...................: [STANDARD]
(G)MCH Frequency Latch...............: 400 Mhz
System Memory Multiplier ..............: 2.66D
Memory Frequency (Mhz) ..............: 1066
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time........................: 5
tRCD .........................................: 5
tRP'...........................................: 5
tRAS..........................................: 15

Advanced Timing Control [Press Enter]
tRRD...........................................: 3
tWTR..........................................: 11
tWR............................................: 6
tRFC...........................................: 42
tRTP...........................................: 5
Command Rate (CMD) ....................: 2

Channel A
Static tRead Value.........................:7
tRD Phase0 Adjustment...................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Channel B
Static tRead Value.........................:7
tRD Phase0 Adjustment...................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Motherboard Voltage ControlCPUMCH/ICHAdvanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Disabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]

**Lsdmeasap** · 08-25-2008, 12:43 AM

Re: (EP45-DS3R) What would be a good setting to come to DDR2-1200?

OK Here is what I would start with trying for ram at 1200 and CPU at 3.6

Have you been trying and failed or just wanted to start trying?

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: [Auto]
CPU Clock Ratio ..........................: 8
CPU Frequency ...........................: 3600

Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 450
PCI Express Frequency (Mhz) .........:Set to 100

Advanced Clock Control [Press Enter] (copied from another topic)
CPU Clock Drive...........................: 800
PCI Express Clock Drive.................: 900
CPU Clock Skew (ps)....................: 150ps
MCH Clock Skew (ps)...................: 250ps

DRAM Performance Control
Performance Enhance...................: [STANDARD]
(G)MCH Frequency Latch...............: 400 Mhz
System Memory Multiplier ..............: 2.66D
Memory Frequency (Mhz) ..............: 1197
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time........................: 5
tRCD .........................................: 5
tRP'...........................................: 5
tRAS..........................................: 15

May actually just need 666-12 or 666-15 above to boot.

Advanced Timing Control [Press Enter]
tRRD...........................................: 3-5
tWTR..........................................: 11-14
tWR............................................: 8-12
tRFC...........................................: 42-50
tRTP...........................................: 5-6
Command Rate (CMD) ....................: 2

Channel A
Static tRead Value.........................:7 << May need 8 or 9
tRD Phase0 Adjustment...................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Channel B
Static tRead Value.........................:7 << May need 8 or 9
tRD Phase0 Adjustment...................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Motherboard Voltage Control
Voltage Type.………... Manual
CPU
CPU Vcore….……….........................: 1.50v
CPU Termination…..... 1.200V*.......: 1.20v
CPU PLL…………………....1.500V*.......: 1.50v
CPU Referen.…………....0.755V*.......: [Auto]

MCH/ICH
MCH Core…………….....1.100V...........: 1.16v << May need a little bit more
MCH Reference….…….0.800V...........; [Auto]
MCH/DRAM Ref.…......0.900V...........: [Auto]
ICH I/O……………….....1.500V............: 1.57v

DRAM
DRAM Voltage ……....1.800V............: 2.10v
DRAM Termination .…0.900V............: [Auto]
Channel A Reference 0.900V............: [Auto]
Channel B Reference 0.900V............: [Auto]

Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Disabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]

**gugle** · 08-25-2008, 09:23 AM

Re: (EP45-DS3R) What would be a good setting to come to DDR2-1200?

Lsdmeasap, I had already tried but without success
Follow your setup, but when you try to enter the Win of BS

put all the most you passed me
and vdimm 2.30v

**Lsdmeasap** · 08-25-2008, 09:34 AM

Re: (EP45-DS3R) What would be a good setting to come to DDR2-1200?

Your CPU may not reach 3.6 is why. And with Vdroop you may have a hard time. I am looking now for a mod for you, but not seeing anything good yet

**gugle** · 08-25-2008, 11:28 AM

Re: (EP45-DS3R) What would be a good setting to come to DDR2-1200?

Originally posted by Lsdmeasap View Post

Your CPU may not reach 3.6 is why. And with Vdroop you may have a hard time. I am looking now for a mod for you, but not seeing anything good yet

here is stable at 3500mhz (438x8)
I tried to run with these times with DDR2-1162, but also not satisfied

you have a good setup for DDR2-1162?

**Lsdmeasap** · 08-25-2008, 11:14 PM

Re: (EP45-DS3R) What would be a good setting to come to DDR2-1200?

If you are sure your CPU is stable then try this, if this fails then either your ram just will not run that high or you need to take the ram out of it so we can be sure your CPU is stable.

To do that you would set ram to all Auto except the first 4 and use 666-24 on those. If that fails then your CPU is not stable or you need more volts to your ram

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: [Auto]
CPU Clock Ratio ..........................: 8
CPU Frequency ...........................: 3500

Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 438
PCI Express Frequency (Mhz) .........:Set to 100

Advanced Clock Control [Press Enter] (copied from another topic)
CPU Clock Drive...........................: 800
PCI Express Clock Drive.................: 900
CPU Clock Skew (ps)....................: 150ps
MCH Clock Skew (ps)...................: 250ps

DRAM Performance Control
Performance Enhance...................: [STANDARD]
(G)MCH Frequency Latch...............: 400 Mhz <<< Also Try 333 here since you are using Higher FSB and 1:1

System Memory Multiplier ..............: 2.66D
Memory Frequency (Mhz) ..............: 1165
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time........................: 5
tRCD .........................................: 5
tRP'...........................................: 5
tRAS..........................................: 15 - 18

May actually just need 666-12 or 666-15 above to boot. Did you try this? If so you ram just may not do over or close to 1066. What amount of ram is this 2x1 or 2x2

Advanced Timing Control [Press Enter]
tRRD...........................................: 3-5
tWTR..........................................: 11-14
tWR............................................: 8-12
tRFC...........................................: 52-65
tRTP...........................................: 5-6
Command Rate (CMD) ....................: 2

Channel A
Static tRead Value.........................:7 << May need 8 or 9 (try 10-12)
tRD Phase0 Adjustment...................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Channel B
Static tRead Value.........................:7 << May need 8 or 9 (try 10-12)
tRD Phase0 Adjustment...................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Motherboard Voltage Control
Voltage Type.………... Manual
CPU
CPU Vcore….……….........................: 1.50v
CPU Termination…..... 1.200V*.......: 1.20v
CPU PLL…………………....1.500V*.......: 1.50v
CPU Referen.…………....0.755V*.......: [Auto]

MCH/ICH
MCH Core…………….....1.100V...........: 1.16v << May need a little bit more. Try 1.3 +
MCH Reference….…….0.800V...........; [Auto]
MCH/DRAM Ref.…......0.900V...........: [Auto]
ICH I/O……………….....1.500V............: 1.57v

DRAM
DRAM Voltage ……....1.800V............: 2.10v << Try 2.2-2.3
DRAM Termination .…0.900V............: [Auto]
Channel A Reference 0.900V............: [Auto]
Channel B Reference 0.900V............: [Auto]

Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Disabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]

**gugle** · 08-26-2008, 12:11 AM

Re: (EP45-DS3R) What would be a good setting to come to DDR2-1200?

the motherboard restarted, and now it's more boot
it turns on or off, On-Off

I tried clear-cmos, remove the battery, exchange CPU, VGA, but nothing happens.

is calling and off, and does not emit any beep

help me

**Lsdmeasap** · 08-26-2008, 12:19 AM

Re: (EP45-DS3R) What would be a good setting to come to DDR2-1200?

What did you do to cause that? None of the above settings should have caused that at all, you sure you did not set Static tRead to low?

Try unplugging your PSU and Putting a Hard drive or optical Jumper on the Clear CMOS pins for 20+ minutes. Then remove all ram but one stick in slot one. And remove the jumper and plug your PSU back in and start the system

**gugle** · 08-26-2008, 12:51 AM

Re: (EP45-DS3R) What would be a good setting to come to DDR2-1200?

not set anything outside of normal

I took the PSU, VGA, all memory (4x1gb), and put the jumper in the clear-cmos for several hours, only left the CPU,

Start with 1gb in slot1 and also did not work ..

is the motherboard died?

**Lsdmeasap** · 08-26-2008, 01:57 AM

Re: (EP45-DS3R) What would be a good setting to come to DDR2-1200?

Sounds like it is. Did you try starting it with each 1GB stick at a time in slot one? Maybe one of them is dead from you trying to overclock them so far... Or all of them? Can you test them on a different board to be sure?

Do you have other ram to try in your board?\

Can you also try to start it with NO Hard Drive connected.

Do you have a floppy already connected? It HAS to be already setup before now. If so you can blind flash the BIOS.

If not you will need to RMA the board

**gugle** · 08-26-2008, 08:40 AM

Re: (EP45-DS3R) What would be a good setting to come to DDR2-1200?

I will try to get another memory test, I am only trying to connect with CPU/VGA/1 MEMO, everything else out

I have floppy, as I try to get flash bios?

**Lsdmeasap** · 08-26-2008, 02:08 PM

Re: (EP45-DS3R) What would be a good setting to come to DDR2-1200?

The Floppy drive had to be installed already/before now. And set as first boot device.

If you had one installed like that then you can try this >>>>
Award 6.0 BIOS - BootBlock Recovery

**gugle** · 08-27-2008, 12:13 AM

Re: (EP45-DS3R) What would be a good setting to come to DDR2-1200?

Originally posted by Lsdmeasap View Post

The Floppy drive had to be installed already/before now. And set as first boot device.

If you had one installed like that then you can try this >>>>
Award 6.0 BIOS - BootBlock Recovery

as I put the floopy first if not the video ??

Announcement

(EP45-DS3R) What would be a good setting to come to DDR2-1200?

(EP45-DS3R) What would be a good setting to come to DDR2-1200?

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment