Ud3p & e8400

[Tyreman]

Any suggestioms for a higher OC suggest away
Thou the ram will be OCing



MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............Auto
CPU Clock Ratio ..........................9x
Fine CPU Clock Ratio.....................0.0
CPU Frequency ........................... 3.60mhz (400X9) 3600MHz
Clock Chip Control
CPU Host Clock Control..................Enabled
CPU Host Frequency (Mhz) ............400
PCI Express Frequency (Mhz) .....100 lock
C.I.A.2 .................................:[Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................800 default
PCI Express Clock Drive................900 default
CPU Clock Skew (ps)....................0
MCH Clock Skew (ps)...................0
DRAM Performance Control
Performance Enhance................Standard
Extreme Memory Profile (X.M.P.).....disabled
(G)MCH Frequency Latch............... AUTO
System Memory Multiplier(SPD).......2.00D “D” Strap is for 400FSB
Memory Frequency (Mhz) ..............800 Running 1:1 @ 800mhz
DRAM Timing Table ................Manual

Standard Timing Control
CAS Latency Time............... 5
tRCD ................................4
tRP'...................................4
tRAS..................................12
Advanced Timing Control
tRRD..........................................3
tWTR..........................................4
tWR............................................6
tRFC...........................................52
tRTP...........................................3
Command Rate (CMD) .................2 T
Driving Strength Profiles
Driving Strength Channels A&B.......1066

Channel A
Static tRead Value..........................8
tRD Phase0 Adjustment...................auto
tRD Phase1 Adjustment...................auto
tRD Phase2 Adjustment ..................auto
tRD Phase3 Adjustment...................auto
Trd2rd(Different Rank)....................auto
Twr2wr(Different Rank)...................auto
Twr2rd(Different Rank)................... auto
Trd2wr(Same/Diff Rank)..................auto
Dimm1 Clock Skew Control...............auto
Dimm2 Clock Skew Control...............auto<?xml:namespace prefix = o ns = "urn:schemas-microsoft-com:office:office" /><o:p></o:p>
DDR Write Training……………………………..auto

Channel B
Static tRead Value..........................8

tRD Phase0 Adjustment...................auto
tRD Phase1 Adjustment...................auto
tRD Phase2 Adjustment ..................auto
tRD Phase3 Adjustment...................auto
Trd2rd(Different Rank)....................auto
Twr2wr(Different Rank)...................auto
Twr2rd(Different Rank)................... auto
Trd2wr(Same/Diff Rank)..................auto
Dimm1 Clock Skew Control...............auto
Dimm2 Clock Skew Control...............auto<o:p></o:p>
DDR Write Training……………………………..auto

Motherboard Voltage Control
Voltage Type.………... Manual <o:p></o:p>
CPU<o:p></o:p>
Load Line…………….Disabled
CPU Vcore….……….....1.24375v <o:p></o:p>
(cpu vid range 0.850v-1.36250v)<o:p></o:p>
CPU Termination….....1.200v
CPU PLL…………………...1.500V
CPU Reference.…………Auto sets this well<o:p></o:p>
<o:p></o:p>
MCH/ICH
MCH Core…………….....1.160V stability and boot
MCH Reference….…….Auto
MCH/DRAM Ref.….....Auto
ICH I/O………………......1.500V
ICH Core…………...…….1.100

DRAM
DRAM Voltage ……........1.840v
DRAM Termination….....0.920v
Channel A Reference…..0.920v
Channel B Reference…..0.920v

Advanced Settings
Limit CPUID Max. to 3....................disabled
No-Execute Memory Protect.............enabled
CPU Enhanced Halt (C1E)................enabled throttles according to load
C2/C2E State Support.....................disabled
x C4/C4E State Support...................disabled
CPU Thermal Monitor2(TM2).............enabled
CPU EIST Function..........................disabled

primed 24 hours and change
Passed IBT Max on 20 passess

[Lsdmeasap]

Re: Ud3p &amp; e8400

If your temps are good, and you have a decent cooler you can easily run 4Ghz.

In my signature is a review on your memory, with settings I used for several speeds on this ram, maybe that would give you some ideas?

You should put MCH/Dram ref. on auto

[Tyreman]

Re: Ud3p &amp; e8400

Yes, thats right I remember your ram critique!
Thanks Much

[Lsdmeasap]

Re: Ud3p &amp; e8400

Cool, wasn't sure if you had seen that or not.

If you use any settings from it, or you just need further help feel free to let us know and we will advise

[Tyreman]

Re: Ud3p &amp; e8400

Update: will run with these settings on and on primed 24hrs at 425x9 3825mhz

The only changes required to the template above for that were:

Mch Core...........................1.200v

Dram Voltage....................2.040
Dram termination...............0.910v
Channel A reference...........0.910v
Channel B reference............0.910v

Static T read...................... 9
Ram 1:1 @ 850MHz
Thats not bad for a real cool running unit and no other voltage or settings changes

[Lsdmeasap]

Re: Ud3p &amp; e8400

Sounds good, nice to see no errors!

[Tyreman]

Re: Ud3p &amp; e8400

upped the cpu host fequency to 429(9x429) 3861 3.86Ghz
MCH core..................1.220v
Ram @ 858 now

no other changes
still pretty good
prime 95 no errors
blend test as above was also.

[kick]

Re: Ud3p &amp; e8400

hey again tyre,its been awhile

http://forums.tweaktown.com/gigabyte/40805-775-quads-duals-hi-fsb-ep-45-ud3.html

[Tyreman]

Re: Ud3p &amp; e8400

Thanks
I am taking my time with this one.

[Tyreman]

Re: Ud3p &amp; e8400

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ..............Auto
CPU Clock Ratio ..........................9x
Fine CPU Clock Ratio.....................0.0
CPU Frequency ........................... 3.60mhz (3600mhz) or 3.86 (3860mhz)
Clock Chip Control
CPU Host Clock Control..................Enabled
CPU Host Frequency (Mhz) ............400(3600mhz) or 429 (3860mhz)
PCI Express Frequency (Mhz) ....100 lock
C.I.A.2 .................................:[Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................800 default
PCI Express Clock Drive................900 default
CPU Clock Skew (ps)....................0
MCH Clock Skew (ps)...................0
DRAM Performance Control
Performance Enhance................Standard
Extreme Memory Profile (X.M.P.).....disabled
(G)MCH Frequency Latch............... AUTO
System Memory Multiplier(SPD).......2.00D “D” Strap 400FSB
Memory Frequency (Mhz) ..............800 1:1(3600) or 858 1:1(3860mhz)
DRAM Timing Table .......................Manual

Standard Timing Control
CAS Latency Time..............5
tRCD ................................4
tRP'...................................4
tRAS.................................12
Advanced Timing Control
tRRD...........................................3
tWTR..........................................4
tWR............................................6
tRFC...........................................52
tRTP...........................................3
Command Rate (CMD) ....................2 T
Driving Strength Profiles
Driving Strength Channels A&B.......1066

Channel A
Static tRead Value..........................8(3600mhz) or 9 (3860mhz)
tRD Phase0 Adjustment...................auto
tRD Phase1 Adjustment...................auto
tRD Phase2 Adjustment ..................auto
tRD Phase3 Adjustment...................auto
Trd2rd(Different Rank)....................auto
Twr2wr(Different Rank)...................auto
Twr2rd(Different Rank)...................auto
Trd2wr(Same/Diff Rank)..................auto
Dimm1 Clock Skew Control...............auto
Dimm2 Clock Skew Control...............auto
DDR Write Training………………………..auto

Channel B
Static tRead Value..........................8(3600mhz) or 9 (3860mhz)

tRD Phase0 Adjustment...................auto
tRD Phase1 Adjustment...................auto
tRD Phase2 Adjustment ..................auto
tRD Phase3 Adjustment...................auto
Trd2rd(Different Rank)....................auto
Twr2wr(Different Rank)...................auto
Twr2rd(Different Rank)................... auto
Trd2wr(Same/Diff Rank)..................auto
Dimm1 Clock Skew Control...............auto
Dimm2 Clock Skew Control...............auto
DDR Write Training………………………..auto

Motherboard Voltage Control
Voltage Type.………... Manual
CPU
Load Line…………….Disabled
CPU Vcore….……….....1.24375v (cpu vid range 0.850v-1.36250v)
CPU Termination….....1.200v
CPU PLL…………………...1.500V
CPU Reference.…………Auto sets this well or 0.760v for stock VTT of 1.200v

MCH/ICH
MCH Core…………….....1.160V(3600mhz) or 1.220v (3860mhz) stability and boot
MCH Reference….…….Auto or 0.760v for stock sets with CPU Ref above
MCH/DRAM Ref.….....0.920v(3600mhz) or 0.910v(3860mhz) or AUTO works fine
ICH I/O………………......1.500V
ICH Core…………...…….1.100v

DRAM
DRAM Voltage ……........1.840v(3600mhz) or 2.040v for(3860mhz)
DRAM Termination…......0.920v 0.910v “
Channel A Reference……0.920v 0.910v “
Channel B Reference…..0.920v 0.910v “

Advanced Settings
Limit CPUID Max. to 3......................disabled
No-Execute Memory Protect.............enabled
CPU Enhanced Halt (C1E)................enabled throttles according to load
C2/C2E State Support.....................disabled
x C4/C4E State Support...................disabled
CPU Thermal Monitor2(TM2).............enabled
CPU EIST Function..........................disabled

cpu Temps around 52/53 load
Although not the fastest currently......the unit is VERY cool and VERY stable.
24hours plus of Prime Blend

[Tyreman]

Re: Ud3p &amp; E8400

Here is another template in the works and running 12 hours with new ram now on prime 95 blend
If it helps somebody so be it!
If there is any changes or would be a failure I will adjust as required and so note.
testing now with new ram Mushkins #996593 4gb(2x2gb)
8000 Redline
DDR2-1000's


MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster .................:Auto
CPU Clock Ratio ..........................: 9
Fine CPU Clock Ratio .....................:0.0
CPU Frequency ............................:3.96GHz (440x9) 3960Ghz.

Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: Enabled
CPU Host Frequency (Mhz) .............:440Mhz
PCI Express Frequency (Mhz) ..........:100
C.I.A.2 ................................: Disabled

Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 800
PCI Express Clock Drive.................:900
CPU Clock Skew (ps)......................:0ps
MCH Clock Skew (ps).....................:0ps

DRAM Performance Control
Performance Enhance....................: [Standard]
Extreme Memory Profile (X.M.P.)........:[Disabled]
(G)MCH Frequency Latch.................: [Auto]
System Memory Multiplier ..............: 2.00D
Memory Frequency (Mhz) ................: 800 @ 880mhz 1:1
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time................5
tRCD ..................................5
tRP'................................... 5
tRAS..................................12

Advanced Timing Control
tRRD........................................... auto
tWTR...........................................aut o
tWR............................................ auto
tRFC........................................... auto
tRTP........................................... auto
Command Rate (CMD) ...................2T

Driving Strength Profiles
Driving Strength ............................ 1066

Channel A
Static tRead Value..........................: 9
tRD Phase0 Adjustment...................: Auto
tRD Phase1 Adjustment....................: Auto
tRD Phase2 Adjustment ....................: Auto
tRD Phase3 Adjustment.....................: Auto
Trd2rd(Different Rank)......................: Auto
Twr2wr(Different Rank).....................: Auto
Twr2rd(Different Rank)......................: Auto
Trd2wr(Same/Diff Rank).....................: Auto
Dimm1 Clock Skew Control..................: Auto
Dimm2 Clock Skew Control..................: Auto

Channel B
Static tRead Value..............................: 9
tRD Phase0 Adjustment.......................: Auto
tRD Phase1 Adjustment.......................: Auto
tRD Phase2 Adjustment ......................: Auto
tRD Phase3 Adjustment.......................: Auto
Trd2rd(Different Rank)........................: Auto
Twr2wr(Different Rank).......................: Auto
Twr2rd(Different Rank)........................: Auto
Trd2wr(Same/Diff Rank)......................: Auto
Dimm1 Clock Skew Control....................: Auto
Dimm2 Clock Skew Control....................: Auto

Motherboard Voltage Control
Voltage Type.………... Manual
CPU
Load Line Calibration .................: Disabled
CPU Vcore......................:1.25000V as set/seen in bios. then under test:HW Monitor shows 1.18v, cpuz 1.184
CPU Termination…...............:1.220V
CPU PLL..............................:1.500V
CPU Reference.........0.760V*........:Auto v

MCH/ICH
MCH Core……………............................:1.280V
MCH Reference….…….0.760V..............:Auto v
MCH/DRAM Ref.…....0.900V................:Auto v
ICH I/O……………….....1.500V.............:1.500V
ICH Core…………......1.100V...............:1.200V

DRAM
DRAM Voltage ……....1.800V.............: 2.040V
DRAM Termination .…0.900V............: 1.020v
Channel A Reference 0.900V............: 1.020v
Channel B Reference 0.900V............: 1.020v

Advanced BIOS Features
Limit CPUID Max. to 3 ........................: [Disabled]
No-Execute Memory Protect ................: [Enabled]
CPU Enhanced Halt (C1E) ....................: Enabled
C2/C2E State Support .........................: [Disabled]
x C4/C4E State Support .......................: [Disabled]
CPU Thermal Monitor 2 (TM2) ..............: [Enabled]
CPU EIST Function ..............................:[Disabled]

[kick]

Re: Ud3p &amp; e8400

What memory bandwidth and latency are u getting tyre?

[Tyreman]

Re: Ud3p &amp; e8400

Haven't tested yet Kick still running prime blend but will test and post when done prime blend
I will post my results

[Tyreman]

Re: Ud3p &amp; e8400

63.2 latency
BUT I had to set ram 2 settings to 4-4 as noted in above template and now prime blend test again.

[Tyreman]

Re: Ud3p &amp; e8400

had to set ram timings back to the 5-5-5
(4's no good here)
Then Latency tested 3 times 64.9, 64.1, 64.0 were the results
will retest again blend on prime 95 to be sure then as time permits work up the OC a bit more later