Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 2 of 2 FirstFirst 12
Results 11 to 14 of 14

Thread: ASrock Fatal1ty 970 performance does not POST 6 short beep code




  1. #11
    Goose Figueroa is offline Junior Member
    Join Date
    Nov 2015
    Location
    Dallas, TX
    Posts
    6

    Default Re: ASrock Fatal1ty 970 performance does not POST 6 short beep code

    Yes, I plugged in the 8 pin ATX 12V, the 24 pin one, and the 6 pin PCIe for my video card. All the fans from the PSU, the CPU, the Video card run normally.

  2. #12
    Goose Figueroa is offline Junior Member
    Join Date
    Nov 2015
    Location
    Dallas, TX
    Posts
    6

    Default Re: ASrock Fatal1ty 970 performance does not POST 6 short beep code

    Quote Originally Posted by - wardog - View Post
    You're good. UDIMM is simply the "new' name for desktop memory.
    So UDIMM or DIMM don't matter? ok
    The only reason i went for DIMM was because this site from ASrock only talks about DIMMs
    ASRock > Fatal1ty 970 Performance
    Memory Support List

    Note1: 4PCS= Dual channel, supports 4 modules.
    Note2: 2PCS = Tested successfully with 2 modules.
    Note3: The O.C. mode is not guaranteed. It depends on whole system configuration and other parameters.
    Note4: For system stability, use more efficient memory cooling system to support a full memory load (4 DIMMs) when overclocking.
    Note5: The mainboard supports DDR3-2000 MHz DIMMs only when you install a 6-core cpu to the mainboard.
    Note6: When overclocking, some AMD CPU models may not support DDR3 1600 MHz or higher frequency DIMMs.
    Note7: Due to CPU spec, AMD 100 and 200 series CPUs support up to DDR3 1066 MHz. With ASRock design, this motherboard can support DDR3 1333 MHz.

  3. #13
    Join Date
    Nov 2012
    Location
    USA
    Posts
    2,675

    Default Re: ASrock Fatal1ty 970 performance does not POST 6 short beep code

    What brand/model/make of KB and mouse are you using to set this up with?

    Try using a bone stock PS/2 KB and mouse. Otherwise ........
    #1 - Please, when seeking help, enter the make and model of ALL parts that your system is comprised of in your Signature, or at least the model #'s in your System Specs, then "Save' it.
    ____If you are overclocking, underclocking, or undervolting any parts, informing us of this and their values would prove beneficial in helping you.

    #2 - G.Skill RAM Configurator for your boardSamsung Memory for your boardLatest AMD Chipset Drivers/WindowsLatest AMD Graphics Drivers/WindowsLatest Intel Drivers

    #3 - Please use the eXtreme Outer Vision Power Supply Calculator found HERE to determine if it might be your PSU at issue.
    ____Consider your PSU to be the foundation from which all else is built upon. Anything built upon a weak foundation is poorly built.

  4. #14
    Join Date
    Nov 2012
    Location
    USA
    Posts
    2,675

    Default Re: ASrock Fatal1ty 970 performance does not POST 6 short beep code

    And please reset your BIOS while the computer is unplugged and unpowered after removing whatever KB and mouse you've been attempting this with. Plugging the PS/2 ones in before powering back up.
    #1 - Please, when seeking help, enter the make and model of ALL parts that your system is comprised of in your Signature, or at least the model #'s in your System Specs, then "Save' it.
    ____If you are overclocking, underclocking, or undervolting any parts, informing us of this and their values would prove beneficial in helping you.

    #2 - G.Skill RAM Configurator for your boardSamsung Memory for your boardLatest AMD Chipset Drivers/WindowsLatest AMD Graphics Drivers/WindowsLatest Intel Drivers

    #3 - Please use the eXtreme Outer Vision Power Supply Calculator found HERE to determine if it might be your PSU at issue.
    ____Consider your PSU to be the foundation from which all else is built upon. Anything built upon a weak foundation is poorly built.

Page 2 of 2 FirstFirst 12

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •