Hallo TweakTown,

I'm currently setting up a ZFS box based on Asrock Z87 Extreme11/ac board. It's hard to get a grip on board's sensors output:

Code:
[email protected] ~ $ sudo sensors-detect --auto# sensors-detect revision 6284 (2015-05-31 14:00:33 +0200)
# Board: ASRock Z87 Extreme11/ac
# Kernel: 4.15.0-13-generic x86_64
# Processor: Intel(R) Core(TM) i5-4460 CPU @ 3.20GHz (6/60/3)


Running in automatic mode, default answers to all questions
are assumed.


Some south bridges, CPUs or memory controllers contain embedded sensors.
Do you want to scan for them? This is totally safe. (YES/no):
Module cpuid loaded successfully.
Silicon Integrated Systems SIS5595...                       No
VIA VT82C686 Integrated Sensors...                          No
VIA VT8231 Integrated Sensors...                            No
AMD K8 thermal sensors...                                   No
AMD Family 10h thermal sensors...                           No
AMD Family 11h thermal sensors...                           No
AMD Family 12h and 14h thermal sensors...                   No
AMD Family 15h thermal sensors...                           No
AMD Family 16h thermal sensors...                           No
AMD Family 15h power sensors...                             No
AMD Family 16h power sensors...                             No
Intel digital thermal sensor...                             Success!
    (driver `coretemp')
Intel AMB FB-DIMM thermal sensor...                         No
Intel 5500/5520/X58 thermal sensor...                       No
VIA C7 thermal sensor...                                    No
VIA Nano thermal sensor...                                  No


Some Super I/O chips contain embedded sensors. We have to write to
standard I/O ports to probe them. This is usually safe.
Do you want to scan for Super I/O sensors? (YES/no):
Probing for Super-I/O at 0x2e/0x2f
Trying family `National Semiconductor/ITE'...               No
Trying family `SMSC'...                                     No
Trying family `VIA/Winbond/Nuvoton/Fintek'...               Yes
Found `Nuvoton NCT5573D/NCT5577D/NCT6776F Super IO Sensors' Success!
    (address 0x290, driver `nct6775')
Probing for Super-I/O at 0x4e/0x4f
Trying family `National Semiconductor/ITE'...               No
Trying family `SMSC'...                                     No
Trying family `VIA/Winbond/Nuvoton/Fintek'...               No
Trying family `ITE'...                                      No


Some systems (mainly servers) implement IPMI, a set of common interfaces
through which system health data may be retrieved, amongst other things.
We first try to get the information from SMBIOS. If we don't find it
there, we have to read from arbitrary I/O ports to probe for such
interfaces. This is normally safe. Do you want to scan for IPMI
interfaces? (YES/no):
Probing for `IPMI BMC KCS' at 0xca0...                      No
Probing for `IPMI BMC SMIC' at 0xca8...                     No


Some hardware monitoring chips are accessible through the ISA I/O ports.
We have to write to arbitrary I/O ports to probe them. This is usually
safe though. Yes, you do have ISA I/O ports even if you do not have any
ISA slots! Do you want to scan the ISA I/O ports? (yes/NO):


Lastly, we can probe the I2C/SMBus adapters for connected hardware
monitoring devices. This is the most risky part, and while it works
reasonably well on most systems, it has been reported to cause trouble
on some systems.
Do you want to probe the I2C/SMBus adapters now? (YES/no):
Using driver `i2c-i801' for device 0000:00:1f.3: Intel Lynx Point (PCH)
Module i2c-i801 loaded successfully.


Next adapter: i915 gmbus ssc (i2c-0)
Do you want to scan it? (yes/NO/selectively):


Next adapter: i915 gmbus vga (i2c-1)
Do you want to scan it? (yes/NO/selectively):


Next adapter: i915 gmbus panel (i2c-2)
Do you want to scan it? (yes/NO/selectively):


Next adapter: i915 gmbus dpc (i2c-3)
Do you want to scan it? (yes/NO/selectively):


Next adapter: i915 gmbus dpb (i2c-4)
Do you want to scan it? (yes/NO/selectively):


Next adapter: i915 gmbus dpd (i2c-5)
Do you want to scan it? (yes/NO/selectively):


Next adapter: DPDDC-B (i2c-6)
Do you want to scan it? (yes/NO/selectively):


Next adapter: DPDDC-C (i2c-7)
Do you want to scan it? (yes/NO/selectively):


Next adapter: SMBus I801 adapter at f040 (i2c-8)
Do you want to scan it? (yes/NO/selectively):




Now follows a summary of the probes I have just done.


Driver `nct6775':
  * ISA bus, address 0x290
    Chip `Nuvoton NCT5573D/NCT5577D/NCT6776F Super IO Sensors' (confidence: 9)


Driver `coretemp':
  * Chip `Intel digital thermal sensor' (confidence: 9)


To load everything that is needed, add this to /etc/modules:
#----cut here----
# Chip drivers
coretemp
nct6775
#----cut here----
If you have some drivers built into your kernel, the list above will
contain too many modules. Skip the appropriate ones!


Do you want to add these lines automatically to /etc/modules? (yes/NO)


Unloading i2c-i801... OK
Unloading cpuid... OK


[email protected] ~ $ sensors
coretemp-isa-0000
Adapter: ISA adapter
Package id 0:  +41.0C  (high = +80.0C, crit = +100.0C)
Core 0:        +36.0C  (high = +80.0C, crit = +100.0C)
Core 1:        +38.0C  (high = +80.0C, crit = +100.0C)
Core 2:        +40.0C  (high = +80.0C, crit = +100.0C)
Core 3:        +35.0C  (high = +80.0C, crit = +100.0C)


nct6776-isa-0290
Adapter: ISA adapter
Vcore:          +0.88 V  (min =  +0.00 V, max =  +1.74 V)
in1:            +1.86 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
AVCC:           +3.39 V  (min =  +2.98 V, max =  +3.63 V)
+3.3V:          +3.39 V  (min =  +2.98 V, max =  +3.63 V)
in4:            +0.95 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in5:            +1.69 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in6:            +0.62 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
3VSB:           +3.44 V  (min =  +2.98 V, max =  +3.63 V)
Vbat:           +3.31 V  (min =  +2.70 V, max =  +3.63 V)
fan1:             0 RPM  (min =    0 RPM)
fan2:             0 RPM  (min =    0 RPM)
fan3:             0 RPM  (min =    0 RPM)
fan4:          3075 RPM  (min =    0 RPM)
fan5:          4736 RPM  (min =    0 RPM)
SYSTIN:         +36.0C  (high =  +0.0C, hyst =  +0.0C)  ALARM  sensor = thermistor
CPUTIN:         +39.5C  (high = +80.0C, hyst = +75.0C)  sensor = thermistor
AUXTIN:         +48.5C  (high = +80.0C, hyst = +75.0C)  sensor = thermistor
PECI Agent 0:   +40.0C  (high = +80.0C, hyst = +75.0C)
                         (crit = +100.0C)
PCH_CHIP_TEMP:   +0.0C
PCH_CPU_TEMP:    +0.0C
PCH_MCH_TEMP:    +0.0C
intrusion0:    ALARM
intrusion1:    ALARM
beep_enable:   disabled


[email protected] ~ $
Can someone identify these parameters and correlate with BIOS/UEFI output:

ASRock Z87 Extreme11/ac lm-sensors (linux) configuration-20180408_215315-jpg

Thanks in advance!

With best regards,
Andriy