Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 4 of 11 FirstFirst ... 23456 ... LastLast
Results 31 to 40 of 102

Thread: Just Brought GIGABYTE GA-EP45-DS3R




  1. #31

    Default Re: Just Brought GIGABYTE GA-EP45-DS3R

    Quote Originally Posted by Lsdmeasap View Post
    Yes the vcore you need to watch is CPU-z one. What you set in the BIOS can be anything really as long as CPU-z showing actual voltage is not going to high

    So yeah, you got the right thinking. If you set 1.9 in the BIOS but CPU-z Shows you are getting 1.1 then the voltage you would be worried about in that case would be actual voltage output to the CPU of 1.1


    Your PSU is good as long as it supports your GFX card, which it does right?
    Dual LAN teaming is explained here >>>
    http://forums.tweaktown.com/f69/x48t...teaming-27322/


    Okay cool.

    Also now I'm testing the setting for 3.4gz I can get it to run so far for about 5 mins longest stress test then a thread stops working. I'm sure the Vcore is good on it so what else should should I increase to make stable? I am using the settings that you gave me for 3.4ghz however I changed my Vcore to get to boot and thats it. Sometimes when I run the test it resets the system too. but so far 3.2 is running nice and smooth. If I could get to 3.4ghz I think that would be my max however I'm not sure what I need to change. I'm using all the same settings you gave me for 3.4 even tried with x8 instead of x9 and that didn't work

  2. #32

    Default Re: Just Brought GIGABYTE GA-EP45-DS3R

    My settings for 3.4ghz:

    MB Intelligent Tweaker(M.I.T.)[COLOR=black][FONT=Verdana]
    Robust Graphics Booster ...............: [Auto]
    CPU Clock Ratio ..........................: 9
    Fine CPU Clock Ratio.....................:.0
    CPU Frequency ...........................: 3.40

    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled]
    CPU Host Frequency (Mhz) ............: 377 Mhz (FSB)
    PCI Express Frequency (Mhz) .........:Set to 100


    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 800
    PCI Express Clock Drive.................: <<< 900
    CPU Clock Skew (ps)....................: <<< 150ps << Both may work fine with lower
    MCH Clock Skew (ps)...................: <<< 250ps <<< See above


    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: [400]
    System Memory Multiplier ..............: 2.66
    Memory Frequency (Mhz) ..............: 1002 MHz
    DRAM Timing Selectable ................: [Manual]

    Standard Timing Control
    CAS Latency Time........................5
    tRCD ......................................... 5
    tRP'...........................................5
    tRAS..........................................15


    Advanced Timing Control [Press Enter]
    tRRD........................................... 4
    tWTR..........................................11
    tWR............................................ 5
    tRFC...........................................62
    tRTP........................................... 6
    Command Rate (CMD) ....................:2

    Channel A
    Static tRead Value.........................: 10
    tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Channel B
    Static tRead Value.........................:10
    tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................: 1.55625V (due to Vdroop) in cpu z using 1.46v (if I go any higher then when I open CPU Z it starts off with me using 1.504v so 1.55625 is below that with Vdroop

    CPU Termination…..... 1.200V*.......: <<< Leave
    CPU PLL…………………....1.500V*.......: <<< Leave
    CPU Referen.…………....0.755V*.......: <<< Leave
    CPU Reference2………,,0.800V*.......:<<< Leave

    MCH/ICH
    MCH Core…………….....1.100V...........: << 1.320
    MCH Reference….…….0.800V...........; <<< Leave
    MCH/DRAM Ref.…......0.900V...........: <<< Leave
    ICH I/O……………….....1.550V............: <<< Leave
    ICH Core…………...……1.100V............: <<< Leave

    DRAM
    DRAM Voltage ……....1.800V............: 2.1V
    DRAM Termination .…0.900V............: <<< Leave
    Channel A Reference 0.900V............: <<< Leave
    Channel B Reference 0.900V............: <<< Leave

    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled]

    I got it to run for about 8 mins max so I think the Vcore is good before one of the threads stop working. I know that LSD can work his magic and help with 3.4ghz :)
    Last edited by Shauntx; 08-28-2008 at 12:01 PM.

  3. #33
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Just Brought GIGABYTE GA-EP45-DS3R

    Are you using Orthos to test, or Prime? I think the both can be set to Small or large FTT. Try those tests to see if your CPU is stable for sure. They do not test/stress the ram only CPU. That way you will know which is causing the failures a little better

    Well I would say you may need to play with different setting on this >>>
    CPU Clock Skew (ps)....................: <<< 150ps
    MCH Clock Skew (ps)...................: <<< 250ps

    Like try >>>
    CPU Clock Skew (ps)....................: <<< 0-150ps (try 100 first)
    MCH Clock Skew (ps)...................: <<< 0-250ps (try with above 100, use 200 Here)

    That should be plenty of varibles, I have seen some with higher CPU the MCH as well that said it worked better.

    You could/should maybe try AUTO for those first with 3.4

    And in the end, your Q6000 may just be not a very strong overclocker either. Some are better then others and your voltage in windows does seem to be a bit up there to run 3.2 stable so it just may be close to the best your chip will do

    3.4 isnt that much better then 3.2 anyway, Might just save yourself the headache and stick with 3.2. What is your temps at that voltage?

    You may also try >>>
    PCI Express Frequency (Mhz) .........:Set to 102 (Sometimes this helps with high overclocks)

    YOu may want to lower CPU volts a bit and play with these >>>

    CPU Termination…..... 1.200V*.......: <<< 1.25 may need 1.30 (bump only one or two notches at a time above 1.3)
    CPU PLL…………………....1.500V*.......: <<< May need 1.5+ for 3.4 ~ 1.6 MAX For Q6600 (Often used)
    CPU Referen.…………....0.755V*.......: <<< Try +30 - +50mv
    CPU Reference2………,,0.800V*.......:<<< Try +30 - +50mv


    Also try >>>
    MCH/DRAM Ref.…......0.900V...........: <<< 1.00

    Channel A Reference 0.900V............: <<< 1.00
    Channel B Reference 0.900V............: <<< 1.00


    I know that is a lot of variables to play with, but you want to tweak it so there is how to go about attempting to do so

    Good luck, Wish I was over there I could help you manually alot faster likely

  4. #34

    Default Re: Just Brought GIGABYTE GA-EP45-DS3R

    Ok I'm guessing that 3.2-3.3 is max. What should I start adjusting now to tighten up things? Also my temps are very good when I boot into 3.4 they are 35-37c then on full load 53-56c

  5. #35
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Just Brought GIGABYTE GA-EP45-DS3R

    What settings are you deciding on keeping, aside from wanting to adjust? Then I can better answer that fro ya.

    So you didnt get anywhere with the above info and 3.4?

  6. #36

    Default Re: Just Brought GIGABYTE GA-EP45-DS3R

    Quote Originally Posted by Lsdmeasap View Post
    What settings are you deciding on keeping, aside from wanting to adjust? Then I can better answer that fro ya.

    So you didnt get anywhere with the above info and 3.4?
    I'm sticking with 3.2ghz the settings that you have given me.

  7. #37

    Default Re: Just Brought GIGABYTE GA-EP45-DS3R

    MB Intelligent Tweaker(M.I.T.)

    Robust Graphics Booster Auto
    CPU Clock Ratio 9
    Fine CPU Clock Ratio 0
    CPU Frequency 3.20GHz (9 X 355 FSB = 3.195)

    "Clock Chip Control Standard Clock Control


    Standard Clock Control"

    CPU Host Clock Control [Enabled]
    CPU Host Frequency (Mhz) 355 Mhz (FSB)
    PCI Express Frequency (Mhz) Set to 100

    Advanced Clock Control [Press Enter]

    CPU Clock Drive 800
    PCI Express Clock Drive 900
    CPU Clock Skew (ps) 150ps
    MCH Clock Skew (ps) 250ps

    DRAM Performance Control

    Performance Enhance [STANDARD]
    Extreme Memory Profile (X.M.P.) Disabled
    (G)MCH Frequency Latch 266.00
    System Memory Multiplier 3.00
    Memory Frequency (Mhz) 1065 MHz
    DRAM Timing Selectable [Manual]

    Standard Timing Control

    CAS Latency Time 5
    tRCD 5
    tRP 5
    tRAS 15

    Advanced Timing Control [Press Enter]

    tRRD 4
    tWTR 11
    tWR 5
    tRFC 62
    tRTP 6
    Command Rate (CMD) 2

    Channel A

    Static tRead Value (7-10) 7
    tRD Phase0 Adjustment Auto
    tRD Phase1 Adjustment Auto
    tRD Phase2 Adjustment Auto
    tRD Phase3 Adjustment Auto
    Trd2rd(Different Rank) Auto
    Twr2wr(Different Rank) Auto
    Twr2rd(Different Rank) Auto
    Trd2wr(Same/Diff Rank) Auto
    Dimm1 Clock Skew Control Auto ps
    Dimm2 Clock Skew Control Auto ps

    Channel B

    Static tRead Value (7-10) 7
    tRD Phase0 Adjustment Auto
    tRD Phase1 Adjustment Auto
    tRD Phase2 Adjustment Auto
    tRD Phase3 Adjustment Auto
    Trd2rd(Different Rank) Auto
    Twr2wr(Different Rank) Auto
    Twr2rd(Different Rank) Auto
    Trd2wr(Same/Diff Rank) Auto
    Dimm1 Clock Skew Control Auto ps
    Dimm2 Clock Skew Control Auto ps

    Motherboard Voltage Control
    Voltage Type Manual

    CPU
    Limit CPUID Max. to 3 [Disabled]
    CPU Vcore (1.30-1.35V) 1.46250V
    CPU Termination 1.200V 1.200
    CPU PLL 1.500V 1.500
    CPU Referen 0.755V 0.755
    CPU Reference2 0.800V 0.800

    MCH/ICH

    MCH Core 1.100V : 1.3V
    MCH Reference 0.800V .800
    MCH/DRAM Ref 0.900V 0.900
    ICH I/O 1.550V 1.550
    ICH Core 1.100V 1.100

    DRAM

    DRAM Voltage 1.800V 2.1v
    DRAM Termination 0.900V .900
    Channel A Reference 0.900V 0.900
    Channel B Reference 0.900V 0.900

    Advanced Settings

    No-Execute Memory Protect [Enabled]
    CPU Enhanced Halt (C1E) [Disabled]
    C2/C2E State Support [Disabled]
    x C4/C4E State Support [Disabled]
    CPU Thermal Monitor 2(TM2) [Enabled]
    CPU EIST Function [Disabled]
    Virtualization Technology [Disabled]
    Last edited by Shauntx; 08-29-2008 at 06:58 PM.

  8. #38
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Just Brought GIGABYTE GA-EP45-DS3R

    So what are you using?

    That is a while set of variable settings I gave you. Which do you catually have entered?

    No need to post them if you dont want to, I just was going to offer some suggestions of what may be lowered as those are high end ranges

  9. #39

    Default Re: Just Brought GIGABYTE GA-EP45-DS3R

    Quote Originally Posted by Lsdmeasap View Post
    So what are you using?

    That is a while set of variable settings I gave you. Which do you catually have entered?

    No need to post them if you dont want to, I just was going to offer some suggestions of what may be lowered as those are high end ranges

    I'm using the settings above only thing I really did was change voltage on vcore and mch I guess you didn't see it because the way I put it sorry yesterday was my b-day and started drinking early

    I put all changes that I have in bold for you to see sorry about that I guess it did look confusing.
    Last edited by Shauntx; 08-29-2008 at 07:01 PM.

  10. #40
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Just Brought GIGABYTE GA-EP45-DS3R

    Ahh, that looks better

    You can try these changes >>>
    (G)MCH Frequency Latch 266.00 <<< Starting here first, Try 333 as you are using 335 FSB

    Then once that is ok, you can likely do the following for better performance, remember to test with memtest after each move >>>

    tRRD 4 << Likely 3 will work
    tWTR 11 << 4-6 May give better performance (Test Last)
    tWR 5 << 3-4 may work
    tRFC 62 <<< 48 (50-52 will likely work)
    tRTP 6 << 3-4 will likely work

Page 4 of 11 FirstFirst ... 23456 ... LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •