Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 3 of 5 FirstFirst 12345 LastLast
Results 21 to 30 of 42

Thread: GA-EP43-D3SL crashs




  1. #21
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: GA-EP43-D3SL crashs

    Hmmm

    Please post for me the last settings you tried for 1066. Could be DOA ram. Do you have another board to test them in?

  2. #22
    Join Date
    Aug 2008
    Posts
    38

    Default Re: GA-EP43-D3SL crashs

    My settings:

    obust Graphics Booster ...............: AUTO
    CPU Clock Ratio ..........................: 9X
    Fine CPU Clock Ratio.....................:.0.0
    CPU Frequency ...........................: 3.582 (398 x 9)


    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled]
    CPU Host Frequency (Mhz) ............: 398 Mhz (over this, the system don't boot up)

    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: [400] (I tested with 333 without sucess)
    System Memory Multiplier ..............: [2.00] (Over this, the system don't boot up)
    Memory Frequency (Mhz) ..............: 796 MHz
    DRAM Timing Selectable ................: [Manual]


    This is the maximum I got...

  3. #23
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: GA-EP43-D3SL crashs

    I need to see the full settings please, all of them >>>>

    This is Just a template I use to ask people their settings, pay no attention to the numbers in it, replace with yours

    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............:
    CPU Clock Ratio ..........................:
    Fine CPU Clock Ratio.....................:.0
    CPU Frequency ...........................:


    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled]
    CPU Host Frequency (Mhz) ............: Mhz
    PCI Express Frequency (Mhz) .........:Set to 100


    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< Leave
    PCI Express Clock Drive.................: <<< Leave
    CPU Clock Skew (ps)....................: <<< Leave
    MCH Clock Skew (ps)...................: <<< Leave


    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: [Auto]
    System Memory Multiplier ..............:
    Memory Frequency (Mhz) ..............:
    DRAM Timing Selectable ................: [Manual]

    Standard Timing Control
    CAS Latency Time........................
    tRCD .........................................
    tRP'...........................................
    tRAS..........................................

    Advanced Timing Control
    tRRD...........................................
    tWTR..........................................
    tWR............................................
    tRFC...........................................
    tRTP...........................................
    Command Rate (CMD) ....................:2

    Channel A
    Static tRead Value.........................:7-10
    tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Channel B
    Static tRead Value.........................:7-10
    tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................:
    CPU Termination…..... 1.200V*.......: <<< Leave
    CPU PLL…………………....1.500V*.......: <<< Leave
    CPU Referen.…………....0.755V*.......: <<< Leave
    CPU Reference2………,,0.800V*.......:<<< Leave

    MCH/ICH
    MCH Core…………….....1.100V...........: <<
    MCH Reference….…….0.800V...........; <<< Leave
    MCH/DRAM Ref.…......0.900V...........: <<< Leave
    ICH I/O……………….....1.550V............: <<< Leave
    ICH Core…………...……1.100V............: <<< Leave

    DRAM
    DRAM Voltage ……....1.800V............:
    DRAM Termination .…0.900V............: <<< Leave
    Channel A Reference 0.900V............: <<< Leave
    Channel B Reference 0.900V............: <<< Leave

    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled]

    Thanks

  4. #24
    Join Date
    Aug 2008
    Posts
    38

    Default Re: GA-EP43-D3SL crashs

    I done test. First I tried with one bank only, in a mem test I have a lot of errors...so a tested the other, in memtest its passed in all tests...I think that one bank of dual channel kit is bad...only rma now...thanks a lot!

    Now I have another issue...I Trying to install Windows XP SP2 with the good bank of memory. The installation copy all files, but when pc restart and will start to install windows XP, the system freazes and appears some strage characters in screen in green color...

    Anyone can help me?

    Thanks!

  5. #25
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: GA-EP43-D3SL crashs

    Did you test EACH stick by itself in slot one? If not please do, so you are sure which ram sticks are bad

    Can you post a image of this error? What settings are you using in the BIOS for disk controls? And are you sure those are correct for your setup? Like for XP you need to load a F6 driver at the very begining of install, did you do that? Post pics of Integrated Peripherals BIOS page if you are not sure, so I can see what you have set. Also please tell me what Disk drives you have, and what ports they are connected to (Color and port #)

  6. #26
    Join Date
    Aug 2008
    Posts
    38

    Default Re: GA-EP43-D3SL crashs

    Quote Originally Posted by Lsdmeasap View Post
    Did you test EACH stick by itself in slot one? If not please do, so you are sure which ram sticks are bad

    Can you post a image of this error? What settings are you using in the BIOS for disk controls? And are you sure those are correct for your setup? Like for XP you need to load a F6 driver at the very begining of install, did you do that? Post pics of Integrated Peripherals BIOS page if you are not sure, so I can see what you have set. Also please tell me what Disk drives you have, and what ports they are connected to (Color and port #)
    Yes, I made the test os each memory stick in slot one alone...one of then runs great, but the other has a lot of errors...now I'm using only the good stick and with this I can set memory to 1000 without problems.

    There's no image from error installing XP, because XP only copy the files to hard disk partition and reboot, before start to install, where appears "Press a key to start CD/DVD", i don't press anything, for not enter the cd again and continue installation, so the system freeze and show some strange characters in green (in my last count, three) in this same screen. This occors with cd of winXP SP2 in the drive.

    I tried too after the installation copy the files to drive and reboot remove the cd from drive and left the system to continue installation and apperar a message:
    Press a key to start CD/DVD.....
    Disk Error
    Press Ctrl+Alt+Del


    I have an Seagate Barracuda SATA3gbps 32mb buffer 500GB connect in SATA1 port, the first one. In SATA2 port I have a LG DVD Writer. All setting of disk in Bios is unchanged, I only changed the MIT options.

    For this board I need to load a sata driver with F6 in begining of installation of Windows XP SP2? In my old machine (Athlon64, DFI NF4 board e Seagate SATA 3gbs 160GB) I don't have to load a sata driver, the installation is ok without driver...where I can download this sata driver?

    I can take some photos with my digital camera from error and bios setting and post here if necessary...

    Thanks a lot!

  7. #27
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: GA-EP43-D3SL crashs

    The driver is on your motherboard Install CD and your manual should tell you how to extract the drive off the cd with a Menu.exe file, for some reason it is not posted on your Motherboard page. But yes it is needed for a XP Install

    If your system worked until this ram error and you changed nothing but MIT settings then you should be ok

  8. #28
    Join Date
    Aug 2008
    Posts
    38

    Default Re: GA-EP43-D3SL crashs

    Quote Originally Posted by Lsdmeasap View Post
    The driver is on your motherboard Install CD and your manual should tell you how to extract the drive off the cd with a Menu.exe file, for some reason it is not posted on your Motherboard page. But yes it is needed for a XP Install

    If your system worked until this ram error and you changed nothing but MIT settings then you should be ok
    Thanks again Lsdmeasap! I will try this...But if in begining of installation Windows XP SP2 found the hard disk and copy files into him, why after the rebot occurs this problem? It's strange...
    Why Vista don't need this driver?

    Update: I search the CD of motherboard...but I can't find the driver for installing Windows XP SP2, whats the name of this?

    obs: my memory is going to RMA...
    Last edited by THe Jackal; 09-04-2008 at 07:21 AM.

  9. #29
    Join Date
    Aug 2008
    Posts
    38

    Default Re: GA-EP43-D3SL crashs

    Lsdmeasap, I done some conclusive tests! I found the sata driver (.oem) in cd of motherboard, so I tried to use, but still don't work...

    So, I pick up a Western Digital 160GB SATA2 hard disk from other machine and put in this with GA-EP43-DS3L. For my surprise, Windows XP SP2 installed fine!!

    So, I conclude that is something with my new Seagate Barracuda 500GB. I think in two things:

    1-Some goes wrong 'cause I'm trying to install Windows XP SP2 in a HD that already have Vista X64. ( Vista is on drive C: (partition 1) and I'm trying to install XP SP2 in D: (partition 2)).

    2-Disk damaged?

  10. #30
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: GA-EP43-D3SL crashs

    Hmm, Well XP and vista can be installed on the same drive. XP should need a driver, Vista includes it is why it is not needed for vista.

    Can you search your motherboard Install CD fro Menu.exe? If that is there you will click on it and you will be shown a windows to copy the driver onto a Floppy

    It could just be a random error with your 500Gb disk, as I have not seen or heard of the error. I dont think it has to do with vista being on there.

    Do you need anything on the vista install? If so maybe you would be better off copying/moving what you need from vista to another drive. Then format the disk and install XP first, then Install Vista. Vista will setup the dual boot menu for you, XP wont

Page 3 of 5 FirstFirst 12345 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •