Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 3 of 4 FirstFirst 1234 LastLast
Results 21 to 30 of 32

Thread: Overclock E8400 on EP43-DS3L




  1. #21
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Overclock E8400 on EP43-DS3L

    Na, just maybe some other setting. You would have to always post full settings that fail for me to best tell you why you get BSOD

    Install that chipset driver, it will help you for sure

  2. #22
    Join Date
    Aug 2008
    Posts
    33

    Default Re: Overclock E8400 on EP43-DS3L

    changed my freq latch to 400MHz with 1:1 multi.can still run stable with same speed (385*9)

    will post in forum again when fail at higher FSB.
    Last edited by efilah; 09-17-2008 at 08:36 PM.

  3. #23
    Join Date
    Aug 2008
    Posts
    33

    Default Re: Overclock E8400 on EP43-DS3L

    hey!

    i can boot to windows with these settings.but when running OCCT,got errors few seconds after it started stressing.

    which one need to change to get stable? >.< im trying not to touch the ram timing 4-4-4-12,for better performance.

    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Auto
    CPU Clock Ratio ..........................: x9
    Fine CPU Clock Ratio.....................:.0
    CPU Frequency ...........................: 3600MHz

    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled]
    CPU Host Frequency (Mhz) ............: 400Mhz
    PCI Express Frequency (Mhz) .........:Set to 100

    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 800mv
    PCI Express Clock Drive.................: <<< 900mv
    CPU Clock Skew (ps)....................: <<< Leave
    MCH Clock Skew (ps)...................: <<< Leave

    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: 400MHz
    System Memory Multiplier ..............: 2.00D
    Memory Frequency (Mhz) ..............: 800MHz
    DRAM Timing Selectable ................: [Manual]

    Standard Timing Control
    CAS Latency Time........................ 4
    tRCD ......................................... 4
    tRP'........................................... 4
    tRAS.......................................... 12

    Advanced Timing Control
    tRRD...........................................4
    tWTR.......................................... 6
    tWR............................................ 6
    tRFC........................................... 52
    tRTP........................................... 4
    Command Rate (CMD) ....................:2

    Channel A
    Static tRead Value.........................:10
    tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Channel B
    Static tRead Value.........................: 10
    tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................: 1.31250V (CPU temp at load 48C lolz)
    CPU Termination…..... 1.200V*.......: <<< Leave
    CPU PLL…………………....1.500V*.......: <<< Leave
    CPU Referen.…………....0.755V*.......: <<< Leave


    MCH/ICH
    MCH Core…………….....1.100V...........: << 1.300V
    ICH I/O……………….....1.550V............: <<< Leave

    DRAM
    DRAM Voltage ……....1.800V............: 2.1V

    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled]

  4. #24
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Overclock E8400 on EP43-DS3L

    Does memtest86+ pass a few hours of tests? If so, then your CPU is likely the issue, maybe you need more voltages.

    You need to run some different tests to be sure what your error in OCCT is caused by. I would run Memtest86+ awhile to see if it is your ram, and then Orthos Small FFt's to see if CPU is failing

  5. #25
    Join Date
    Aug 2008
    Posts
    33

    Default Re: Overclock E8400 on EP43-DS3L

    ok,already stable at 400*9.its my CPU which runs pretty hot that make it unstable.my elite331 have bad air venhtilation.i open the casing (side panel one),the temp decrease about 4C lolz!!! then i put a fan beside the casing,drop 2-3C more.now stable.

    here's the setting :

    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Auto
    CPU Clock Ratio ..........................: x9
    Fine CPU Clock Ratio.....................:.0
    CPU Frequency ...........................: 3600MHz

    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled]
    CPU Host Frequency (Mhz) ............: 400Mhz
    PCI Express Frequency (Mhz) .........:100

    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 800mv
    PCI Express Clock Drive.................: <<< 900mv
    CPU Clock Skew (ps)....................: <<< Leave
    MCH Clock Skew (ps)...................: <<< Leave

    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: 400MHz
    System Memory Multiplier ..............: 2.00D
    Memory Frequency (Mhz) ..............: 800MHz
    DRAM Timing Selectable ................: [Manual]

    Standard Timing Control
    CAS Latency Time........................ 4
    tRCD ......................................... 4
    tRP'........................................... 4
    tRAS.......................................... 12

    Advanced Timing Control
    tRRD...........................................4
    tWTR.......................................... 6
    tWR............................................ 6
    tRFC........................................... 55
    tRTP........................................... 6
    Command Rate (CMD) ....................:2

    Channel A
    Static tRead Value.........................:12
    tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Channel B
    Static tRead Value.........................: 12
    tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................: 1.33125V
    CPU Termination…..... 1.200V*.......: <<< Leave
    CPU PLL…………………....1.500V*.......: <<< Leave
    CPU Referen.…………....0.755V*.......: <<< Leave


    MCH/ICH
    MCH Core…………….....1.100V...........: << 1.200V
    ICH I/O……………….....1.550V............: <<< Leave

    DRAM
    DRAM Voltage ……....1.800V............: 2.1V

    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled]
    Last edited by efilah; 09-19-2008 at 02:16 PM.

  6. #26
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Overclock E8400 on EP43-DS3L

    Those look good, but can be improved. I would start by getting Static tRead as low as you can get, Like maybe 7 or 8 first.

    Sounds like you need some more 120MM fans in your case, or a larger cooler!

  7. #27
    Join Date
    Aug 2008
    Posts
    33

    Default Re: Overclock E8400 on EP43-DS3L

    actually my casing can only occupy 2 fans only.both 120mm =x i tried lowering the static tRead.but i'll get blue screen even when surfing using Mozilla Firefox.hoho.i'll try lowering it again next time.

  8. #28
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

  9. #29
    Join Date
    Aug 2008
    Posts
    33

    Default Re: Overclock E8400 on EP43-DS3L

    yeah. im sure.it 4-4-4-12.i'll try 7 or 8 later.

  10. #30
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

Page 3 of 4 FirstFirst 1234 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •