Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 2 of 2 FirstFirst 12
Results 11 to 13 of 13

Thread: EP43-DS3 Overclocking Problems




  1. #11
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: EP43-DS3 Overclocking Problems

    Ahh, Ok! Just wanted to make sure you saw that. What ram you getting?

    Cheap 6750? Isnt that better then the E2160, I would think so. Either way, I doubt it is a CPU issue just the ram

  2. #12
    Join Date
    Sep 2008
    Posts
    7

    Default Re: EP43-DS3 Overclocking Problems

    I've now got my E6750 installed, but I'm still using 2x1g Ballistix until the new ram turns up (both old and new sets at separate times, so I don't think both can be causing the problem) and am having the same troubles as before.

    If I do manage to get in at 3.2g, it'll always revert to stock upon restart, after failing to boot, no matter what volts I've tried, from Auto up to 1.45v, with the NB from 1.1v to 1.3v and ram from Auto to 2.1v.

    In Easytune, the readings state anything from 1.280 in cpu volts, to 1.370 volts, with the temps from 36 idle to 50 idle and when I use Coretemp, it states 58 idle.

    I've never experienced these problems before, in my old DS3R mobo and previous mobo's, if it booted, then it was fine from then on, without the need to alter memory timings, nor the volts in most cases, especially when getting 3g out of my old E2160, but this mobo is either faulty, or the worst overclocker I've ever bought and my last Gigabtye at this rate.

    Two cpu's, two sets of ram and still no stable overclock in over 3 weeks, this is tedious now.

    I'll probably wait until I get some new ram, after being conned on the bay for some and if I still have the same problem, then that's it.

  3. #13
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: EP43-DS3 Overclocking Problems

    Well 1.45 in the BIOS will only be about 1.38 or so actual, your chip may need more then that. I used to have a Xeon 3075, same as E6750 and For me to run 3.4 I had to use 1.425 actual so you may just need a bit more volts

    Crucial May be the issue, but not so sure with that chipset. Will it at least pass a few memtest86+ passes?

    Easytune shows CPU temp, coretemp shows coretemps. They are different things for sure. And a 58C idel core temp is not so good. You sure you have the heatsink fully screwed on? And not to much paste?

    Please just so I can see where you are post your full settings for the 6750 and I will see if I see anything off >>>

    This is Just a template I use to ask people their settings, pay no attention to the numbers in it, replace with yours

    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............:
    CPU Clock Ratio ..........................:
    Fine CPU Clock Ratio.....................:.0
    CPU Frequency ...........................:


    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled]
    CPU Host Frequency (Mhz) ............: Mhz
    PCI Express Frequency (Mhz) .........:Set to 100

    C.I.A.2 .................................:[Disabled]


    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<<
    PCI Express Clock Drive.................: <<<
    CPU Clock Skew (ps)....................: <<<
    MCH Clock Skew (ps)...................: <<<


    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: [Auto]
    System Memory Multiplier ..............:
    Memory Frequency (Mhz) ..............:
    DRAM Timing Selectable ................: [Manual]

    Standard Timing Control
    CAS Latency Time........................
    tRCD .........................................
    tRP'...........................................
    tRAS..........................................

    Advanced Timing Control
    tRRD...........................................
    tWTR..........................................
    tWR............................................
    tRFC...........................................
    tRTP...........................................
    Command Rate (CMD) ....................:2

    Driving Strength Profiles
    Driving Strength ............................

    Channel A
    Static tRead Value.........................:7-10
    tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Channel B
    Static tRead Value.........................:7-10
    tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................:
    CPU Termination…..... 1.200V*.......: <<< Leave
    CPU PLL…………………....1.500V*.......: <<< Leave
    CPU Referen.…………....0.755V*.......: <<< .61% Of Vtt (Termination above)
    CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above)

    MCH/ICH
    MCH Core…………….....1.100V...........: <<
    MCH Reference….…….0.800V...........; <<< Leave
    MCH/DRAM Ref.…......0.900V...........: <<< Leave
    ICH I/O……………….....1.550V............: <<< Leave
    ICH Core…………...……1.100V............: <<< Leave

    DRAM
    DRAM Voltage ……....1.800V............:
    DRAM Termination .…0.900V............: <<< Leave
    Channel A Reference 0.900V............: <<< Leave
    Channel B Reference 0.900V............: <<< Leave

    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled]

    Integrated Peripherals
    Legacy USB Storage Detect___________________[Disabled] *Note* Must be enabled to flash from USB

Page 2 of 2 FirstFirst 12

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •