Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 2 of 2 FirstFirst 12
Results 11 to 15 of 15

Thread: DES Application EP45-ds3r questions




  1. #11
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: DES Application EP45-ds3r questions

    Ahh, yes well you did not show me all settings, I need to see the full pages of MIT which you did not post any of. And please post your full specs as well

  2. #12
    Join Date
    Oct 2008
    Posts
    8

    Default Re: DES Application EP45-ds3r questions

    I hope this is what your after.





    The components consist of:
    Intel Q6600
    EVGA 8600GTS


    Gigabyte Technology Co., Ltd.
    Model : EP45-DS3R
    ID : 00000000-00000000-1D000000-1A580A7D

    System Chassis
    Manufacturer : Gigabyte Technology Co., Ltd.
    Type : Desktop
    Can be locked : No

    Mainboard
    Manufacturer : Gigabyte Technology Co., Ltd.
    Multi-Processor (MP) Support : No
    MPS Version : 1.40
    Model : EP45-DS3R
    Version : x.x
    System BIOS : 06/18/2008-P45-ICH10-7A89PG01C-00

    System Memory Controller
    Location : Mainboard
    Error Correction Capability : None
    Number of Memory Slots : 4
    Maximum Installable Memory : 4GB
    Bank0/1 - A0 : DIMM 2GB/64 @ 800MHz
    Bank2/3 - A1 : DIMM 2GB/64 @ 800MHz
    Bank4/5 - A2 : Empty
    Bank6/7 - A3 : Empty

    Chipset
    Model : Giga-Byte Eaglelake DRAM Controller
    Revision : A3
    Bus : Intel AGTL+
    Independent FSB Channels : 1
    Front Side Bus Speed : 4x 267MHz (1.07GHz)
    Maximum FSB Speed : 4x 400MHz (1.60GHz)
    Width : 64-bit
    Crossfire Technology : Yes
    I/O Queue Depth : 12 request(s)
    Maximum Bus Bandwidth : 8.34GB/s

    Features
    TXT - Trust Execution Technology : Yes
    ME - Management Engine : Yes
    AMT - Active Management Technology : Yes
    VT-d - Virtualisation Technology : Yes
    EF - EastFork Technology : Yes
    AP - Agent Presence : Yes
    CB - Circuit Breaker : Yes
    Auto Fan Speed Control : Yes

    Chipset 1 Hub Interface
    Type : DMI (Direct Media Interface)
    Version : 1.00
    Number of Ports : 4
    In/Out Width : 4-bit / 4-bit
    Multiplier : 3/1x
    Speed : 1x 100MHz (100MHz)

    Logical/Chipset Memory Banks
    Bank 0 : 1GB DIMM DDR3 2-5-5-18 3-23-10-7 2T
    Bank 1 : 1GB DIMM DDR3 2-5-5-18 3-23-10-7 2T
    Bank 2 : 1GB DIMM DDR3 2-5-5-18 3-23-10-7 2T
    Bank 3 : 1GB DIMM DDR3 2-5-5-18 3-23-10-7 2T
    Maximum Installable Memory : 8GB
    Supported Memory Types : DIMM DDR2 DDR3
    Channels : 1
    Memory Bus Speed : 2x 401MHz (802MHz)
    Multiplier : 6/4x
    Width : 64-bit
    Memory Controller in Processor : No
    FMA - Fast Memory Access Support : Yes
    Refresh Rate : 7.80s
    Power Save Mode : No
    Fixed Hole Present : No
    Maximum Memory Bus Bandwidth : 6.27GB/s

    APIC 1
    Version : 2.00
    Multiplier : 1/2x
    Maximum Interrupts : 24
    IRQ Handler Engaged : Yes
    Enhanced Support : Yes

    Memory Module
    Manufacturer : Corsair
    Model : CM2X2048-6400C5
    Type : 2GB DIMM DDR2
    Technology : 16x(128Mx8)
    Speed : PC2-6400U DDR2-800
    Standard Timings : 5.0-5-5-18 3-22-6-3
    Version : 1.02
    Memory DC Line : 1.80V
    Set Timing @ 400MHz : 5.0-5-5-18 3-22-6-3
    Set Timing @ 270MHz : 4.0-3-3-12 2-15-4-2

    Memory Module
    Manufacturer : Corsair
    Model : CM2X2048-6400C5
    Type : 2GB DIMM DDR2
    Technology : 16x(128Mx8)
    Speed : PC2-6400U DDR2-800
    Standard Timings : 5.0-5-5-18 3-22-6-3
    Version : 1.02
    Memory DC Line : 1.80V
    Set Timing @ 400MHz : 5.0-5-5-18 3-22-6-3
    Set Timing @ 270MHz : 4.0-3-3-12 2-15-4-2

    Environment Monitor 1
    Model : ITE IT8718F LPC
    Version : 5.00
    Mainboard Specific Support : No

    Environment Monitor 2
    Model : Intel Core CPU [P1, C4, M0]
    Version : 15.11
    Mainboard Specific Support : No

    Environment Monitor 3
    Model : ITE ITE820X SMB
    Mainboard Specific Support : No

    Temperature Sensor(s)
    Board Temperature : 36.00C
    CPU Temperature : 33.00C td

    Cooling Device(s)
    Auto Fan Speed Control : No
    System Fan : 1152rpm
    Auxliary Fan : 1934rpm

    Voltage Sensor(s)
    CPU DC Line : 1.14V
    Aux DC Line : 1.90V
    +3.3V DC Line : 3.33V
    +5V DC Line : 5.05V
    +12V DC Line : 0.87V
    -12V DC Line : -16.64V
    -5V DC Line : -8.48V
    Standby DC Line : 5.11V
    Battery DC Line : 3.22V

    System Bus(es) on Hub 1
    Version : 2.30
    System Bus 0 : PCI
    System Bus 1 : PCIe 2.00 x16 2.5Gbps
    System Bus 2 : PCIe 1.00 x1 2.5Gbps
    System Bus 3 : PCIe 1.00 x1 2.5Gbps
    System Bus 4 : PCIe 1.00 x1 2.5Gbps
    System Bus 5 : PCIe 1.00 x1 2.5Gbps
    System Bus 6 : PCIe 1.00 x1 2.5Gbps
    System Bus 7 : PCI66

    LPC Hub Controller 1
    Model : Giga-Byte LPC Interface Controller
    Revision : A1
    ACPI Power Management Enabled : Yes
    Advanced TCO Mode Support : Yes
    Advanced TCO Mode Enabled : No
    High Precision Timer Enabled : Yes
    Number of Precision Timers : 4
    System Timer : 14.32MHz
    Delayed Transaction Enabled : Yes

    Disk Controller
    Model : Giga-Byte 4 port SATA IDE Controller
    Interface : SATA
    Revision : A1
    Maximum SATA Mode : G2 / SATA300
    RAID Support : Yes
    RAID Enabled : No
    Channels : 4
    In Use Channels : 3
    Port : G1 / SATA150
    Port : G1 / SATA150
    Port : G1 / SATA150

    Disk Controller
    Model : Giga-Byte 2 port SATA IDE Controller
    Interface : ATA
    Revision : A1
    Channels : 4

    Disk Controller
    Model : Giga-Byte JMB368 IDE Controller
    Interface : ATA
    Revision : A1
    Channels : 4

    Audio Device
    Model : Giga-Byte HD Audio Controller
    Revision : A1
    Type : HD (High-Definition) Audio
    Version : 1.00
    Number of In / Out / Bi-Directional Streams : 4 / 4 / 0
    Number of Serial Data Streams : 1

    USB Controller 1
    Model : Giga-Byte USB UHCI Controller #4
    Revision : A1
    Version : 1.10
    Interface : UHCI
    Channels : 2
    Speed : 48MHz
    Supported Speed(s) : Low (1.5Mbps) Full (12Mbps)
    Legacy Emulation Enabled : No

    USB Controller 2
    Model : Giga-Byte USB UHCI Controller #5
    Revision : A1
    Version : 1.10
    Interface : UHCI
    Channels : 2
    Speed : 48MHz
    Supported Speed(s) : Low (1.5Mbps) Full (12Mbps)
    Legacy Emulation Enabled : No

    USB Controller 3
    Model : Giga-Byte USB UHCI Controller #6
    Revision : A1
    Version : 1.10
    Interface : UHCI
    Channels : 2
    Speed : 48MHz
    Supported Speed(s) : Low (1.5Mbps) Full (12Mbps)
    Legacy Emulation Enabled : No

    USB Controller 4
    Model : Giga-Byte USB EHCI Controller #2
    Revision : A1
    Version : 2.00
    Specification : 1.00
    Interface : EHCI
    Channels : 6
    Companion Controllers : 3
    Supported Speed(s) : Low (1.5Mbps) Full (12Mbps) High (480Mbps)
    Addressing Support : 64-bit
    Legacy Emulation Enabled : No

    USB Controller 5
    Model : Giga-Byte USB UHCI Controller #1
    Revision : A1
    Version : 1.10
    Interface : UHCI
    Channels : 2
    Speed : 48MHz
    Supported Speed(s) : Low (1.5Mbps) Full (12Mbps)
    Legacy Emulation Enabled : No

    USB Controller 6
    Model : Giga-Byte USB UHCI Controller #2
    Revision : A1
    Version : 1.10
    Interface : UHCI
    Channels : 2
    Speed : 48MHz
    Supported Speed(s) : Low (1.5Mbps) Full (12Mbps)
    Legacy Emulation Enabled : No

    USB Controller 7
    Model : Giga-Byte USB UHCI Controller #3
    Revision : A1
    Version : 1.10
    Interface : UHCI
    Channels : 2
    Speed : 48MHz
    Supported Speed(s) : Low (1.5Mbps) Full (12Mbps)
    Legacy Emulation Enabled : No

    USB Controller 8
    Model : Giga-Byte USB EHCI Controller #1
    Revision : A1
    Version : 2.00
    Specification : 1.00
    Interface : EHCI
    Channels : 6
    Companion Controllers : 3
    Supported Speed(s) : Low (1.5Mbps) Full (12Mbps) High (480Mbps)
    Addressing Support : 64-bit
    Legacy Emulation Enabled : No

    FireWire/1394 Controller 1
    Model : Giga-Byte TSB43AB23 1394a-2000 OHCI PHY/link-layer Controller
    Revision : A1
    Version : 1.10
    Interface : OHCI
    Enhanced Support : Yes
    Channels : 64
    Speed : 400MHz

    System SMBus Controller 1
    Model : Intel 801xx/63xx SMBus
    Specification : 2.00
    Advanced TCO Mode Enabled : Yes
    Slave Device Enabled : Yes
    PEC Support : Yes
    Speed : 100kHz

    Expansion Slot(s)
    PCI : PCI 32-bit +5V +3.3V PME i2c/SMBus Full-Length Available
    PCI (1h) : PCI 32-bit +5V +3.3V PME i2c/SMBus Full-Length Available

    Port Connector(s)
    PRIMARY IDE : ATA
    SECONDARY IDE : ATA
    FDD : 8251 FIFO / Floppy Disk
    COM1 : Serial Port 16450 / 9 Pin Dual Inline / DB-9 pin male
    COM2 : Serial Port 16450 / 9 Pin Dual Inline / DB-9 pin male
    LPT1 : Parallel Port ECP/EPP / DB-25 pin female / DB-25 pin female
    Keyboard : Keyboard / PS/2
    PS/2 Mouse - Detected : Mouse / PS/2 / PS/2
    USB : USB / USB
    USB : USB / USB

  3. #13
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: DES Application EP45-ds3r questions

    So you want Some best tweaked settings for your system now right? If so, Sorry that is a bit unlcear because of everest. I see you have Corsair 6400 ram, but not sure how many sticks and what they are. Can you please just state 4x1 or 4x2, ect, and if you can link me to where you bought them so I may check warrantied voltages

  4. #14
    Join Date
    Oct 2008
    Posts
    8

    Default Re: DES Application EP45-ds3r questions

    There are 2 2gig sticks of Ram. I bought them at the local Microcenter.
    Micro Center - Twin 2X 4GB PC-6400 DDR2 CL4 Memory Kit (Two 2GB DDR2-800 Memory Modules)
    I wish I could be more help but I'm pretty much a Noob here. I did load the bio's with the "optimum" settings.

  5. #15
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: DES Application EP45-ds3r questions

    OK, thanks

    Here is some suggested Ranges for you to tweak your ram to, with your CPU Set as you have it already. Ranges mean set to the highest first and tweak later moving one at a time testing with memtest86+ between each move >>>>

    Code:
    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Fast
    CPU Clock Ratio ..........................: 9
    Fine CPU Clock Ratio.....................:.0
    CPU Frequency ...........................: 2.40
    
    
    Clock Chip Control 
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled] 
    CPU Host Frequency (Mhz) ............: 266Mhz
    PCI Express Frequency (Mhz) .........:Set to 100
    
    C.I.A.2 .................................:[Disabled]
    
    
    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 
    PCI Express Clock Drive.................: <<< 
    CPU Clock Skew (ps)....................: <<< 
    MCH Clock Skew (ps)...................: <<< 50-150
    
    
    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: [333]
    System Memory Multiplier ..............: 3.20
    Memory Frequency (Mhz) ..............: 850Mhz
    DRAM Timing Selectable ................: [Manual]
    
    Or you may use this instead of the above>>>
    (G)MCH Frequency Latch...............: [266]
    System Memory Multiplier ..............: 3.00
    Memory Frequency (Mhz) ..............: 800Mhz
    
    Standard Timing Control
    CAS Latency Time........................4
    tRCD .........................................4
    tRP'...........................................4
    tRAS..........................................12
    
    Set all highest below, then lower later
    
    Advanced Timing Control
    tRRD...........................................3-6
    tWTR..........................................3-6 (Will need 8-12 to first boot thru, use 12)
    tWR............................................3-6 (Will need 8-14 to first boot thru, use 14)
    tRFC...........................................52-62 (Set 68 first)
    tRTP...........................................3-6
    Command Rate (CMD) ....................:2
    
    Driving Strength Profiles
    Driving Strength ............................800-1066 (1066 may be best)
    
    Channel A
    Static tRead Value.........................:7-10 (Use 10 first)
     tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
     tRD Phase2 Adjustment .................:Auto
     tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 
    Twr2wr(Different Rank)...................:Auto 
    Twr2rd(Different Rank)...................:Auto 
    Trd2wr(Same/Diff Rank)..................:Auto 
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
    
    Channel B
    Static tRead Value.........................:7-10 (Use 10 first)
     tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
     tRD Phase2 Adjustment .................:Auto
     tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 
    Twr2wr(Different Rank)...................:Auto 
    Twr2rd(Different Rank)...................:Auto 
    Trd2wr(Same/Diff Rank)..................:Auto 
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
    
    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................:
    CPU Termination…..... 1.200V*.......: <<< Leave
    CPU PLL…………………....1.500V*.......: <<< 1.5
    CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above)
    CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above)
    
    MCH/ICH
    MCH Core…………….....1.100V...........: << 1.15-1.25-1.3
    MCH Reference….…….0.800V...........; <<< Leave
    MCH/DRAM Ref.…......0.900V...........: <<< Leave
    ICH I/O……………….....1.550V............: <<< Leave
    ICH Core…………...……1.100V............: <<< Leave
    
    DRAM
    DRAM Voltage ……....1.800V............: 2.0-2.1V
    DRAM Termination .…0.900V............: <<< Leave
    Channel A Reference 0.900V............: <<< Leave
    Channel B Reference 0.900V............: <<< Leave
    
    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled]
    
    Integrated Peripherals
    Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB

Page 2 of 2 FirstFirst 12

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •