Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 26

Thread: Ga-ep31-ds3l need help here!!!




  1. #11

    Default Re: Ga-ep31-ds3l need help here!!!

    idle temps seem high, are you sure ur load temps are correct?
    and 38c for a system is good :D
    ur load temps are +10 from idle, seems normal.

  2. #12
    Join Date
    Oct 2008
    Posts
    15

    Default Re: Ga-ep31-ds3l need help here!!!

    sometime it will raise to 48c-51c,so wat can i do next

  3. #13
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Ga-ep31-ds3l need help here!!!

    4Ghz is ALOT to ask out of a 2.5GHz CPU, so you may want to back off your wish of a 4Ghz overclock because with that voltage being needed your CPU is going to die VERY QUICKLY!!

    3.6-3.8 is a bit more acceptable, and would only need 1.38-1.4 or so

    Here is some suggested 3.825 settings

    Code:
    Robust Graphics Booster___________ [Auto]
    CPU Clock Ratio ____________ [9] 
    Fine Clock Ratio ____________[0.0]
    CPU Host Clock Control_ [Enabled]
    CPU Host Frequency (MHz)__________ [425] 
    PCI Express Frequency (Mhz)_______ [100]
    C.I.A. 2__________________________ [Disabled]
    System Memory Multiplier (SPD)____ [2.00] = 850 Ram speed
    DRAM Timing Selectable_______ SPD __ [Manual]
    
    Performance Enhance = [Standard]
    
    CAS Latency Time________________ 5
    Dram RAS# to CAS# Delay_________ 5
    Dram RAS# Precharge Delay_______5
    Precharge Delay (tRAS)__________ 15/18
    
    Use all highest below first, then later lower and test between each move
    
    ACT to ACT Delay (tRRD)_________3-5
    Rank Write to READ Delay________ 3-6 (9-1, Benchmark this, as 9-11 is often better)
    Write to Precharge Delay_________4-6
    Refresh to ACT Delay______________ 48-50 (52-62) Has to be high for 2x2GB
    Read to Precharge Delay__________ 3-6
    Static tRead Value_______________ 7(8-10)
    Static tRead Phase Adjust________ [Auto] << always leave
    
    System Voltage Control____ [Manual]
    DDR2 OverVoltage Control__ [+0.300V] 
    PCI-E OverVoltage Control_ [+0.1V] 
    FSB OverVoltage Control___ [+0.1V] 
    (G)MCH OverVoltage Control [+0.1V - +0.2 - +0.25] << Needed for 2x2GB
    CPU Voltage Control_______ [1.35- 1.45] 1.5 or more is killing your CPU
    
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled]

  4. #14
    Join Date
    Oct 2008
    Posts
    15

    Default Re: Ga-ep31-ds3l need help here!!!

    cant set to x9 bro it always goin to default setting even i raise up to 1.49v

  5. #15
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Ga-ep31-ds3l need help here!!!

    What can you not set to 9? CPU Mutli? Why not, you have loaded optimized defaults with that CPU installed before right?

  6. #16
    Join Date
    Oct 2008
    Posts
    15

    Default Re: Ga-ep31-ds3l need help here!!!

    the default e5200 multiplier 200x12.5 =2.5ghz

  7. #17
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Ga-ep31-ds3l need help here!!!

    Yes, so you cannot use 9? You should be able to lower it for sure, again have you loaded optimized defaults since you installed that CPU? If not you need to when you change CPU's

  8. #18
    Join Date
    Oct 2008
    Posts
    15

    Default Re: Ga-ep31-ds3l need help here!!!

    yeah i already optimize default bro,so wat is the next step

  9. #19
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Ga-ep31-ds3l need help here!!!

    Show me a picture of the top of your MIT page, you will need to take it with a camera.

    You should be able to choose a CPU Multi, you do have this enabled correct? >>>
    CPU Host Clock Control..................: [Enabled]

    You should be able to press enter on CPU Clock Ratio and then enter a number, Num Lock would have to of course be pressed. So also post a pic of this popup box as well

  10. #20
    Join Date
    Oct 2008
    Posts
    15

    Default Re: Ga-ep31-ds3l need help here!!!

    f i set 425x9 have to use more then 1.5 cpu voltage bro,ofcoz i can use the to select the multiplier even (x8)

Page 2 of 3 FirstFirst 123 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •