Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 3 of 4 FirstFirst 1234 LastLast
Results 21 to 30 of 36

Thread: GA-EP45-DS3R (e7200)




  1. #21
    Join Date
    Oct 2008
    Location
    Trnava, Slovakia
    Posts
    18

    Default Re: GA-EP45-DS3R (e7200)

    Quote Originally Posted by Lsdmeasap View Post
    Do you maybe have your fans set to low for your cooler, or pointed wrong? What speeds do these fans run, and how are you controlling them?
    I think they are on maximum:/ I dont know how to control them

  2. #22
    Join Date
    Oct 2008
    Location
    Trnava, Slovakia
    Posts
    18

    Default Re: GA-EP45-DS3R (e7200)

    ok so i made a little test
    i start OCCT, Speedfan and look for temperature
    When it shows 70 C i touch it, it was cold, and graphic card shows 54 C and its hot
    so there are two options (if im right):
    1. temperature of cpu is ok but some temperature sensors are bad
    2. there is some problem which incurred that cooler is cool but he doenst cool the cpu

    my english realy sux:P

    im sure that cooler is instaled correct, coz i was very focused, and with this belaying technologi isnt way to instal it bad and dont see it...

  3. #23
    Join Date
    Oct 2008
    Location
    Trnava, Slovakia
    Posts
    18

    Default Re: GA-EP45-DS3R (e7200)

    ok now i have this setup:

    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............:
    CPU Clock Ratio ..........................: 8
    Fine CPU Clock Ratio.....................:.0.5
    CPU Frequency ...........................: 3.41 (402*8.5=3417Mhz)


    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled]
    CPU Host Frequency (Mhz) ............: 402 Mhz
    PCI Express Frequency (Mhz) .........:100

    C.I.A.2 .................................:[Disabled]


    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: 800
    PCI Express Clock Drive.................: 900
    CPU Clock Skew (ps)....................: 0
    MCH Clock Skew (ps)...................: 0


    DRAM Performance Control
    Performance Enhance...................: [Standard]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: 400
    System Memory Multiplier ..............: 2.00
    Memory Frequency (Mhz) ..............: 804
    DRAM Timing Selectable ................: [Manual]

    Standard Timing Control
    CAS Latency Time........................ 4
    tRCD ......................................... 4
    tRP'........................................... 4
    tRAS.......................................... 11

    Advanced Timing Control
    tRRD........................................... Auto
    tWTR.......................................... Auto
    tWR............................................ Auto
    tRFC........................................... 60
    tRTP........................................... Auto
    Command Rate (CMD) ....................: 2

    Driving Strength Profiles
    Driving Strength ............................ 800

    Channel A
    Static tRead Value.........................: 11
    tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Channel B
    Static tRead Value.........................: 11
    tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................: 1.35
    CPU Termination…..... 1.200V*.......: 1.28
    CPU PLL…………………....1.500V*.......: Auto
    CPU Referen.…………....0.755V*.......: Auto
    CPU Reference2………,,0.800V*.......: Auto

    MCH/ICH
    MCH Core…………….....1.100V...........: 1.2
    MCH Reference….…….0.800V...........; Auto
    MCH/DRAM Ref.…......0.900V...........: Auto
    ICH I/O……………….....1.550V............: Auto
    ICH Core…………...……1.100V............: Auto

    DRAM
    DRAM Voltage ……....1.800V............: 2.0
    DRAM Termination .…0.900V............: Auto
    Channel A Reference 0.900V............: Auto
    Channel B Reference 0.900V............: Auto

    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Disabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled]

    And just before OCCT end i got error message : CODE 4, it means: calculation error ("code 4 in one of the threads as even if the problem is memory/NB related, it will lead to calculation error")

    Please have you some solution for me?

  4. #24
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

  5. #25
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: GA-EP45-DS3R (e7200)

    Yes, for the above, all those Auto settings can cause memory errors. And you may want to add a bit more MCH, and possibly set ram to 2.1 if your ram allows it

    Could also be vcore. Only way to be SURE is to run memtest86+ with those exact settings for a few hours to be sure if it is your ram or not.

  6. #26
    Join Date
    Oct 2008
    Location
    Trnava, Slovakia
    Posts
    18

    Default Re: GA-EP45-DS3R (e7200)

    Quote Originally Posted by Lsdmeasap View Post
    Yes, for the above, all those Auto settings can cause memory errors. And you may want to add a bit more MCH, and possibly set ram to 2.1 if your ram allows it

    Could also be vcore. Only way to be SURE is to run memtest86+ with those exact settings for a few hours to be sure if it is your ram or not.
    And please can you tell me some settings for these rams? Coz i dont know what i have to setup. i find settup 4-4-4-11 tRC 20 on 2V, or 4 4 4 12 tRC 22 on 2V.But i cant find tRC in bios settings. I think that 2,1 i cant make, coz everytime when i was trying to setup this, i cant get to windows.

    Core Temp Shows max 71 C. But if are senzors on motherboard bad it will show this temperature in every software right?

  7. #27
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: GA-EP45-DS3R (e7200)

    trc is not in your BIOS. WOW, that is hot for a coretemp. What CPU Speed and voltage are you using?

    We have given you settings, are you not getting anywhere or what? Just wonder what you have tried. I see you say you cannot get into windows, but I need to know why. So please post what you are trying (Full settings) and I will see if I can tell you why maybe it is failing

  8. #28
    Join Date
    Oct 2008
    Location
    Trnava, Slovakia
    Posts
    18

    Default Re: GA-EP45-DS3R (e7200)

    i tryed settings which you and wizard gave me here, i tryed settings from other topics, i tryed a lot of things, and today, i have stable setup, but only 3,21 ghz:( here it is:

    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............:
    CPU Clock Ratio ..........................: 8
    Fine CPU Clock Ratio.....................:.0
    CPU Frequency ...........................: 3.21 (402*8)


    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled]
    CPU Host Frequency (Mhz) ............: 402 Mhz
    PCI Express Frequency (Mhz) .........:100

    C.I.A.2 .................................:[Disabled]


    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: 800
    PCI Express Clock Drive.................: 900
    CPU Clock Skew (ps)....................: 100
    MCH Clock Skew (ps)...................: 150


    DRAM Performance Control
    Performance Enhance...................: [Standard]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: 400
    System Memory Multiplier ..............: 2.00
    Memory Frequency (Mhz) ..............: 804
    DRAM Timing Selectable ................: [Manual]

    Standard Timing Control
    CAS Latency Time........................ 4
    tRCD ......................................... 4
    tRP'........................................... 4
    tRAS.......................................... 12

    Advanced Timing Control
    tRRD........................................... 3
    tWTR.......................................... 12
    tWR............................................ 14
    tRFC........................................... 60
    tRTP........................................... 8
    Command Rate (CMD) ....................: 2

    Driving Strength Profiles
    Driving Strength ............................ 800

    Channel A
    Static tRead Value.........................: 10
    tRD Phase0 Adjustment...................: Auto
    tRD Phase1 Adjustment...................: Auto
    tRD Phase2 Adjustment ..................: Auto
    tRD Phase3 Adjustment...................: Auto
    Trd2rd(Different Rank)....................: Auto
    Twr2wr(Different Rank)...................: Auto
    Twr2rd(Different Rank)...................: Auto
    Trd2wr(Same/Diff Rank)..................: Auto
    Dimm1 Clock Skew Control...............: Auto
    Dimm2 Clock Skew Control...............: Auto

    Channel B
    Static tRead Value.........................: 10
    tRD Phase0 Adjustment...................: Auto
    tRD Phase1 Adjustment...................: Auto
    tRD Phase2 Adjustment ..................: Auto
    tRD Phase3 Adjustment...................: Auto
    Trd2rd(Different Rank)....................: Auto
    Twr2wr(Different Rank)...................: Auto
    Twr2rd(Different Rank)...................: Auto
    Trd2wr(Same/Diff Rank)..................: Auto
    Dimm1 Clock Skew Control...............: Auto
    Dimm2 Clock Skew Control...............: Auto

    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................: 1.35
    CPU Termination…..... 1.200V*.......: 1.32
    CPU PLL…………………....1.500V*.......: Auto
    CPU Referen.…………....0.755V*.......: Auto

    MCH/ICH
    MCH Core…………….....1.100V...........: 1.2
    MCH Reference….…….0.800V...........; Auto
    MCH/DRAM Ref.…......0.900V...........: Auto
    ICH I/O……………….....1.550V............: Auto
    ICH Core…………...……1.100V............: Auto

    DRAM
    DRAM Voltage ……....1.800V............: 2.0
    DRAM Termination .…0.900V............: Auto
    Channel A Reference 0.900V............: Auto
    Channel B Reference 0.900V............: Auto

    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Disabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled]

    I know that Vcore is high, but now i have stable setup what is perfect for me, but i dont know what now, which options i can decreast and how can i encreast Ghz to some stable value

  9. #29

    Default Re: GA-EP45-DS3R (e7200)

    wow dude,u have the same settings as i had before i sent my board to fixing. and i had ep45-ds3r with E7300!!
    it was stable exactly with this settings!i got it stable at 3.3ghz as well, i will post u back when i get my bpard back, and oc it to far more to 3.6 (if i succeed) cause maybe its a faulty mobo :S
    these are the settings i used for 3.3:

    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............:
    CPU Clock Ratio ..........................: 8
    Fine CPU Clock Ratio.....................:.0
    CPU Frequency ...........................: 3.3 (413*8)(i used multiplier 10 but this is not the point here)


    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled]
    CPU Host Frequency (Mhz) ............: 413 Mhz
    PCI Express Frequency (Mhz) .........:100

    C.I.A.2 .................................:[Disabled]


    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: 800
    PCI Express Clock Drive.................: 900
    CPU Clock Skew (ps)....................: 100, try this at 0
    MCH Clock Skew (ps)...................: 150


    DRAM Performance Control
    Performance Enhance...................: [Standard]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: 400
    System Memory Multiplier ..............: 2.00D
    Memory Frequency (Mhz) ..............: 826
    DRAM Timing Selectable ................: [Manual]

    Standard Timing Control
    CAS Latency Time........................ 4/5
    tRCD ......................................... 4/5
    tRP'........................................... 4/5
    tRAS.......................................... 12/15

    Advanced Timing Control
    tRRD........................................... 6
    tWTR.......................................... 12
    tWR............................................ 14
    tRFC........................................... 60
    tRTP........................................... 8
    Command Rate (CMD) ....................: 2

    Driving Strength Profiles
    Driving Strength ............................ 1066

    Channel A
    Static tRead Value.........................: 10
    tRD Phase0 Adjustment...................: Auto
    tRD Phase1 Adjustment...................: Auto
    tRD Phase2 Adjustment ..................: Auto
    tRD Phase3 Adjustment...................: Auto
    Trd2rd(Different Rank)....................: Auto
    Twr2wr(Different Rank)...................: Auto
    Twr2rd(Different Rank)...................: Auto
    Trd2wr(Same/Diff Rank)..................: Auto
    Dimm1 Clock Skew Control...............: Auto
    Dimm2 Clock Skew Control...............: Auto

    Channel B
    Static tRead Value.........................: 10
    tRD Phase0 Adjustment...................: Auto
    tRD Phase1 Adjustment...................: Auto
    tRD Phase2 Adjustment ..................: Auto
    tRD Phase3 Adjustment...................: Auto
    Trd2rd(Different Rank)....................: Auto
    Twr2wr(Different Rank)...................: Auto
    Twr2rd(Different Rank)...................: Auto
    Trd2wr(Same/Diff Rank)..................: Auto
    Dimm1 Clock Skew Control...............: Auto
    Dimm2 Clock Skew Control...............: Auto

    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................: 1.4/1.3815 and if doesnt work try 1.425
    CPU Termination…..... 1.200V*.......: 1.32
    CPU PLL…………………....1.500V*.......: Auto
    CPU Referen.…………....0.755V*.......: 0.873
    MCH/ICH
    MCH Core…………….....1.100V...........: 1.24/1.3
    MCH Reference….…….0.800V...........; Auto
    MCH/DRAM Ref.…......0.900V...........: Auto
    ICH I/O……………….....1.550V............: Auto
    ICH Core…………...……1.100V............: Auto

    DRAM
    DRAM Voltage ……....1.800V............: 2.1 (check ur dam sticker, mine was 4-4-4-12 at 2.1v, but i tried 5-5-5-15 at 2.1v)
    DRAM Termination .…0.900V............: Auto
    Channel A Reference 0.900V............: Auto
    Channel B Reference 0.900V............: Auto

    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Disabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled]

  10. #30
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: GA-EP45-DS3R (e7200)

    Both of you guys can now bring down some of those settings for sure >>>

    (G)MCH Frequency Latch...............: 400

    Standard Timing Control
    CAS Latency Time........................ 4
    tRCD ......................................... 4
    tRP'........................................... 4
    tRAS.......................................... 12

    Advanced Timing Control
    tRRD........................................... 3
    tWTR.......................................... 3-5
    tWR............................................ 3-6
    tRFC........................................... 48-54
    tRTP........................................... 3-6
    Command Rate (CMD) ....................: 2

    Driving Strength Profiles
    Driving Strength ............................ 800 (1066 may work better)

    Channel A & B
    Static tRead Value.........................: 8-10

Page 3 of 4 FirstFirst 1234 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •