Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 4 of 4 FirstFirst ... 234
Results 31 to 32 of 32

Thread: GA-EP43-D3SL + E8400 - 4GHz?




  1. #31

    Default Re: GA-EP43-D3SL + E8400 - 4GHz?

    I used the same as above, but here it is in full.

    MB Intelligent Tweaker(M.I.T.)

    Robust Graphics Booster ...............: [Auto]
    CPU Clock Ratio ..........................: 9
    Fine CPU Clock Ratio.....................: N/A
    CPU Frequency ...........................: 3.96GHz (9x440=3960MHz) (doesn't work at 9x420, or even 8x420)


    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled]
    CPU Host Frequency (Mhz) ............: 440MHz
    PCI Express Frequency (Mhz) .........: 100MHz <--Always 100!!

    C.I.A.2 .................................:[Disabled]


    Advanced Clock Control
    CPU Clock Drive...........................: 800
    PCI Express Clock Drive.................: 800
    CPU Clock Skew (ps)....................: Auto
    MCH Clock Skew (ps)...................: Auto


    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: 400
    System Memory Multiplier ..............: 2.00
    Memory Frequency (Mhz) ..............: 880MHz
    DRAM Timing Selectable ................: [Manual]

    Standard Timing Control
    CAS Latency Time.............................5
    tRCD ..............................................5
    tRP'.............................................. ...5
    tRAS.............................................. ..18

    Advanced Timing Control
    tRRD........................................... 5
    tWTR.......................................... 7
    tWR............................................ 7
    tRFC........................................... 58
    tRTP........................................... 6
    Command Rate (CMD) ....................: 2

    Channel A
    Static tRead Value............................:12
    tRD Phase0 Adjustment...................: Auto
    tRD Phase1 Adjustment...................: Auto
    tRD Phase2 Adjustment .................: Auto
    tRD Phase3 Adjustment..................: Auto
    Trd2rd(Different Rank)....................: Auto
    Twr2wr(Different Rank)...................: Auto
    Twr2rd(Different Rank)...................: Auto
    Trd2wr(Same/Diff Rank)..................: Auto
    Dimm1 Clock Skew Control...............: Auto
    Dimm2 Clock Skew Control...............: Auto

    Channel B
    Static tRead Value..........................: 12
    tRD Phase0 Adjustment...................: Auto
    tRD Phase1 Adjustment...................: Auto
    tRD Phase2 Adjustment .................: Auto
    tRD Phase3 Adjustment..................: Auto
    Trd2rd(Different Rank)....................: Auto
    Twr2wr(Different Rank)...................: Auto
    Twr2rd(Different Rank)...................: Auto
    Trd2wr(Same/Diff Rank)..................: Auto
    Dimm1 Clock Skew Control...............: Auto
    Dimm2 Clock Skew Control...............: Auto

    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................: 1.4V
    CPU Termination…..... 1.200V*.......: 1.3
    CPU PLL…………………....1.500V*.......: 1.65
    CPU Referen.…………....0.755V*.......: Auto
    CPU Reference2………..0.800V*.......: Auto

    MCH/ICH
    MCH Core…………….....1.100V...........: 1.4V
    ICH Core…………...……1.100V............: 1.2V

    DRAM
    DRAM Voltage ……....1.800V............: 2.1V

    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled]


    When I try these it just get the fans spinning up for a few secs then no beep etc then it just restarts without changes and I get the warning screen when I go back into the settings page.

  2. #32
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: GA-EP43-D3SL + E8400 - 4GHz?

    Try these changes. You did test the ram one by one at stock to be sure you did not get a DOA stick right?

    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: [Auto]
    CPU Clock Ratio ..........................: 9
    Fine CPU Clock Ratio.....................: N/A
    CPU Frequency ...........................: 3.96GHz (9x440=3960MHz) (doesn't work at 9x420, or even 8x420)


    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled]
    CPU Host Frequency (Mhz) ............: 440MHz
    PCI Express Frequency (Mhz) .........: 100MHz <--Always 100!!

    C.I.A.2 .................................:[Disabled]


    Advanced Clock Control
    CPU Clock Drive...........................: 800
    PCI Express Clock Drive.................: 800
    CPU Clock Skew (ps)....................: Auto
    MCH Clock Skew (ps)...................: 100-150


    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: 400
    System Memory Multiplier ..............: 2.00
    Memory Frequency (Mhz) ..............: 880MHz
    DRAM Timing Selectable ................: [Manual]

    Standard Timing Control
    CAS Latency Time.............................5
    tRCD ..............................................5
    tRP'.............................................. ...5
    tRAS.............................................. ..18

    Advanced Timing Control
    tRRD........................................... 5
    tWTR.......................................... 7
    tWR............................................ 7
    tRFC........................................... 58
    tRTP........................................... 6
    Command Rate (CMD) ....................: 2

    Channel A
    Static tRead Value............................:12
    tRD Phase0 Adjustment...................: Auto
    tRD Phase1 Adjustment...................: Auto
    tRD Phase2 Adjustment .................: Auto
    tRD Phase3 Adjustment..................: Auto
    Trd2rd(Different Rank)....................: Auto
    Twr2wr(Different Rank)...................: Auto
    Twr2rd(Different Rank)...................: Auto
    Trd2wr(Same/Diff Rank)..................: Auto
    Dimm1 Clock Skew Control...............: Auto
    Dimm2 Clock Skew Control...............: Auto

    Channel B
    Static tRead Value..........................: 12
    tRD Phase0 Adjustment...................: Auto
    tRD Phase1 Adjustment...................: Auto
    tRD Phase2 Adjustment .................: Auto
    tRD Phase3 Adjustment..................: Auto
    Trd2rd(Different Rank)....................: Auto
    Twr2wr(Different Rank)...................: Auto
    Twr2rd(Different Rank)...................: Auto
    Trd2wr(Same/Diff Rank)..................: Auto
    Dimm1 Clock Skew Control...............: Auto
    Dimm2 Clock Skew Control...............: Auto

    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................: 1.4V
    CPU Termination…..... 1.200V*.......: 1.34
    CPU PLL…………………....1.500V*.......: 1.50 << Also way to high, stock 1.5 is fine
    CPU Referen.…………....0.755V*.......: Auto
    CPU Reference2………..0.800V*.......: Auto

    MCH/ICH
    MCH Core…………….....1.100V...........: 1.4V << Far too much and is likely what is causing you issues. Use 1.2-1.3

    ICH Core…………...……1.100V............: 1.2V

    DRAM
    DRAM Voltage ……....1.800V............: 2.1V

Page 4 of 4 FirstFirst ... 234

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •