Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 4 of 4 FirstFirst ... 234
Results 31 to 35 of 35

Thread: GA-X48T-DQ6 and OCZ ram = random BSoD?




  1. #31
    Join Date
    Oct 2008
    Posts
    6

    Default Re: GA-X48T-DQ6 and OCZ ram = random BSoD?

    Right that sounds good ta, i think i will try 1333 instead.

    Thanks for your help...
    Last edited by Simonpieman; 10-22-2008 at 06:10 PM.

  2. #32
    MDDI is offline Junior Member
    Join Date
    Jul 2008
    Location
    Florida USA
    Posts
    70

    Default Re: GA-X48T-DQ6 and OCZ ram = random BSoD?

    If your RAM, regardless of brand is high voltage and your motherboard will not POST at default settings with it, "BE CAREFUL"!

    I learned the hard way. My board did not want to POST with both 1.8v DIMM's installed. I could however POST with one DIMM installed every two or three attempts.

    I did not take this into consideration when I updated my BIOS. I left both DIMM's installed during a BIOS flash. My board did not POST after the restart so I was unable to enter setup and select "Load Optimized Defaults".

    As a result, the BIOS flash did not finish and turned my board into a square frisbie!

    After that experience and a board RMA I have changed my priority steps for selecting RAM. If my board will not POST at default settings with the RAM I selected I will not use it.

  3. #33
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: GA-X48T-DQ6 and OCZ ram = random BSoD?

    MDDI, next time you have a brick board contact me before you RMA there is several things you can do to fix the BIOS. If you have a floppy set as first boot device, and installed, this is your first lifesaver. There is another way as well to avoid a RMA if you do not have a floppy installed, but I will not be posting that in public, if you would like to know about it PM me and I will forward the info to you.

    Thanks for posting here, Not sure if the OP pm'd you or not but please do (in PM if you like) assure him about 2x2 and or Brands mentioned on page 3

  4. #34
    Join Date
    Feb 2009
    Posts
    2

    Default Re: GA-X48T-DQ6 and OCZ ram = random BSoD?

    hey, im having this same problem, where my pc just randomly bsod's. I have put this down to my RAM timings being incorrect, however i dont know what im doing when it comes to change these kinds of values in my bios, and wondered if i could be cheeky and ask for sum help PLEASE

    ive read this whole topic, and i think somewhere in here in my answer i just dont know where im going wrong, nor what im suppose to do or change.

    Bios: F5
    <!-- / message --><!-- sig -->

    Robust Graphics Booster___________ [Auto]
    CPU Clock Ratio ____________ [6 x]
    CPU Host Clock Control_ [Enabled]
    CPU Host Frequency (MHz)__________ [400]
    PCI Express Frequency (Mhz)_______ [auto]
    C.I.A. 2__________________________ [Disabled]
    Performance Enhance_________[standard]
    Extreme Memory Profile (X.M.P)_______________[profile 1]
    System Memory Multiplier (SPD)____ [auto]
    DRAM Timing Selectable_______ SPD __ [auto]

    Performance Enhance = [Standard]

    CAS Latency Time________________ 7 auto
    Dram RAS# to CAS# Delay_________ 7 auto
    Dram RAS# Precharge Delay_______7 auto
    Precharge Delay (tRAS)__________ 28 auto

    ACT to ACT Delay (tRRD)_________ 5 auto
    Write to Precharge Delay_________ 12 auto
    Refresh to ACT Delay______________ 72 auto
    Read to Precharge Delay__________ 6 auto
    Static tRead Value_______________ 7 auto

    Static tRead Phase Adjust________ [Auto]

    CPU/PCIEX Clock Driving Control [800mV]
    CPU Clock Skew Control [normal]
    GMCH Clock Skew Control [Normal]

    System Voltage Control____ [auto]
    DDR3 OverVoltage Control__ [normal]
    PCI-E OverVoltage Control_ [normal]
    FSB OverVoltage Control___ [normal]
    (G)MCH OverVoltage Control [normal]
    CPU Voltage Control_______ [normal]
    normal CPU Vcore ________1.32500v

    Any help would be very much appreciated, and thank you for any help

  5. #35
    Join Date
    Oct 2008
    Posts
    11

    Default Re: GA-X48T-DQ6 and OCZ ram = random BSoD?

    I was able to get a RMA from OCZ.. It turned out that one of my sticks seemed to be defective. So no matter how much I tried tuning the timings it didn't have any effect.
    So I will get back to you once I have recieved the new RAM sticks.

Page 4 of 4 FirstFirst ... 234

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •