Nice! I was about to suggest you load optimized and start at the top again. Often helps, and Should ALWAYS be done and applied after a flash as well.

If you do still need some suggested ranges for best performance here ya go >>>

Code:
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: [Fast]
CPU Clock Ratio ..........................: 9
Fine CPU Clock Ratio.....................: N/A
CPU Frequency ...........................: 4.05GHz (450x9)


Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 450MHz
PCI Express Frequency (Mhz) .........:100MHz

C.I.A.2 .................................:[Disabled]


Advanced Clock Control
CPU Clock Drive...........................:800
PCI Express Clock Drive.................:800
CPU Clock Skew (ps)....................: 50
MCH Clock Skew (ps)...................:50-200


DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: 400MHz
System Memory Multiplier ..............: 2.00D
Memory Frequency (Mhz) ..............: 900
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time............................. 4/5
tRCD .............................................. 4/5
tRP'.............................................. ... 4/5
tRAS.............................................. .. 12/15

Advanced Timing Control <
tRRD...........................................3-4
tWTR.......................................... 3-6
tWR............................................4-6
tRFC...........................................46-50 (52-62)
tRTP...........................................3-5
Command Rate (CMD) ....................:2

Channel A
Static tRead Value............................:8-10 
tRD Phase0 Adjustment...................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto
Dimm2 Clock Skew Control...............:Auto

Channel B
Static tRead Value..........................:8-10
tRD Phase0 Adjustment...................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto
Dimm2 Clock Skew Control...............:Auto

Motherboard Voltage Control
Voltage Type.………... Manual
CPU
CPU Vcore….……….........................: 1.4v
CPU Termination…..... 1.200V*.......: 1.2-1.38
CPU PLL…………………....1.500V*.......: 1.5-1.6
CPU Referen.…………....0.755V*.......: Auto
CPU Reference2………,,0.800V*.......: Auto

MCH/ICH
MCH Core…………….....1.100V...........: 1.15-1.3v
MCH Reference….…….0.800V...........:Auto
MCH/DRAM Ref.…......0.900V...........:Auto
ICH I/O……………….....1.550V............:1.5-1.55
ICH Core…………...……1.100V............:1.1-1.2

DRAM
DRAM Voltage ……....1.800V............: 2.0-2.10v

DRAM Termination .…0.900V............: Auto
Channel A Reference 0.900V............: Auto
Channel B Reference 0.900V............: Auto

Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]