Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 2 of 6 FirstFirst 1234 ... LastLast
Results 11 to 20 of 55

Thread: A little help with my EP45-DS3R Please




  1. #11
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: A little help with my EP45-DS3R Please

    That is fine, just your board/cpu/bios do not offer them then. You did load optimized defaults and save and apply/reboot after you flashed right? If not you MUST!

  2. #12
    Join Date
    Oct 2008
    Posts
    54

    Default Re: A little help with my EP45-DS3R Please

    Yes, I did.

  3. #13
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: A little help with my EP45-DS3R Please

    K, then it is just your board/BIOS does not allow you to set them then

  4. #14
    Join Date
    Oct 2008
    Posts
    54

    Default Re: A little help with my EP45-DS3R Please

    So far I haven't been able to pass Memtest yet with out atleast one error. The first session I ran 23 passes on test 7 with out an error. The second was 33 passes with out an error, and this last one went 7 and I received an error.

  5. #15
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: A little help with my EP45-DS3R Please

    Test 7 is hot! How long will it run the normal full range of tests?

  6. #16
    Join Date
    Oct 2008
    Posts
    54

    Default Re: A little help with my EP45-DS3R Please

    I might be jumping the gun with the way I just changed the settings but I am able to boot now using MCH latch of 333 and a Memory Multiplier of 2.00B. The Static Tread Values are now set to 9 and the rest of the settings are the same that I haven't been able to pass Memtest with.

    Here is what I have been testing thus far:
    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: [Fast]
    CPU Clock Ratio ..........................: [ 9 X]
    Fine CPU Clock Ratio.....................:.[+0.5]
    CPU Frequency ...........................: 2.53 GZ (266x9 .5)


    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled]
    CPU Host Frequency (Mhz) ............: [266]
    PCI Express Frequency (Mhz) .........:Set to 100

    C.I.A.2 .................................:[Disabled]


    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: [800mV]
    PCI Express Clock Drive.................: [900mV]
    CPU Clock Skew (ps)....................: [50ps]
    MCH Clock Skew (ps)...................: [200ps]


    DRAM Performance Control
    Performance Enhance...................: [Standard]
    Extreme Memory Profile (X.M.P.).....: Disabled <- As mentioned, not available
    (G)MCH Frequency Latch...............: [333]
    System Memory Multiplier ..............: [2.00b]
    Memory Frequency (Mhz) ..............: 800 533
    DRAM Timing Selectable ................: [Manual]

    Standard Timing Control
    CAS Latency Time........................ [5]
    tRCD ......................................... [5]
    tRP'........................................... [5]
    tRAS.......................................... [15]

    Advanced Timing Control
    tRRD........................................... 3
    tWTR.......................................... 3
    tWR............................................ 6
    tRFC........................................... 70
    tRTP........................................... 3
    Command Rate (CMD) ....................: 2

    Driving Strength Profiles
    Driving Strength ............................ 800 (have been trying 1066, but I figured this pass I would try 800)

    Channel A
    Static tRead Value.........................: 9
    tRD Phase0 Adjustment...................: Auto
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Channel B
    Static tRead Value.........................: 9
    tRD Phase0 Adjustment...................: Auto
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................: 1.4
    CPU Termination…..... 1.200V*.......: 1.28
    CPU PLL…………………....1.500V*.......: 1.6
    CPU Referen.…………....0.755V*.......: 0.760
    CPU Reference2………,,0.800V*.......: not available

    MCH/ICH
    MCH Core…………….....1.100V...........: 1.36
    MCH Reference….…….0.800V...........; Auto
    MCH/DRAM Ref.…......0.900V...........: Auto
    ICH I/O……………….....1.550V............: 1.6
    ICH Core…………...……1.100V............: Not available

    DRAM
    DRAM Voltage ……....1.800V............: 1.900V (Have been trying 2.000V but now trying 1.900V)
    DRAM Termination .…0.900V............: Auto
    Channel A Reference 0.900V............: Auto
    Channel B Reference 0.900V............: Auto

    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled]

    Integrated Peripherals
    Legacy USB Storage Detect ..............[Disabled]

  7. #17
    Join Date
    Oct 2008
    Posts
    54

    Default Re: A little help with my EP45-DS3R Please

    I'm not sure what you mean when you say hot. I ran test 5 for a couple hours with new errors, but since test 7 gave me erros I've been obsessed with passing it. Should I run all test as normal?

  8. #18
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: A little help with my EP45-DS3R Please

    Ya, I would run several hours of the normal test. I use 5 and 7 for short tests when tweaking. I say hot meaning test 5 and 7 make the ram very hot, and running either for several hours by themselves may just give you errors due to heat.

    You may be more stable on the 400 MCH latch if you find errors this time around, and or use 1066 with the 333 latch

    And hey, you did notice you are running you ram at only 533Mhz right?

  9. #19
    Join Date
    Oct 2008
    Posts
    54

    Default Re: A little help with my EP45-DS3R Please

    No, I didn't notice. I've been relying on your guidance thus far, thank you very much for by the way. How do I fix that? And thanks for that heads up I've been running test 7 for 4-6 hours at a time.. lol!

  10. #20
    Join Date
    Oct 2008
    Posts
    54

    Default Re: A little help with my EP45-DS3R Please

    Oops I just checked my BIOS the ram is actually Memory Frequency (MHZ) 800 850. I just didn't notice that when I copy and pasted the settings template from my very first post! doh
    Last edited by JLB2414; 10-23-2008 at 03:33 AM.

Page 2 of 6 FirstFirst 1234 ... LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •