Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Results 1 to 5 of 5

Thread: GA-X48T-DQ6 + 4x OCZ3G13332GK = BSOD




  1. #1
    Join Date
    Oct 2008
    Posts
    2

    Unhappy GA-X48T-DQ6 + 4x OCZ3G13332GK = BSOD

    Hello,

    I have a GA-X48T-DQ6 with a quadcore 9550 and 4 x 1GB OCZ DDR3 with 9-9-9@1,7V

    Memory is tested one by one in slot4 and seems to be ok.
    Windows XP Pro is installed, but gives me random BSOD.
    Since a few days it's even impossible to boot with all the memory installed.
    With only 2x 1GB installed, I can boot.
    Bios settings are still factory defaults.
    What do I need to change to make this combination stable?

  2. #2
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: GA-X48T-DQ6 + 4x OCZ3G13332GK = BSOD

    Why did you test in slot 4? I would say you should test each stick one by one again (Or at least one so you know it is a good one) and then test that good stick in each slot. I say that because maybe you have a bad slot onboard?

    If you find no slots, please post me your settings and what BIOS you are using. I will assume that may be the sole issue as factory defaults are not going to work for 4x1, and not work well for that ram even with 2x1. At those speeds all settings should be manually set

    This is Just a template I use to ask people their settings, pay no attention to the numbers in it, replace with yours

    Code:
    Robust Graphics Booster___________ [Auto]
    CPU Clock Ratio ____________ [8] 
    Fine Clock Ratio ____________[0.5]
    CPU Host Clock Control_ [Enabled]
    CPU Host Frequency (MHz)__________ [450] 
    PCI Express Frequency (Mhz)_______ [100]
    C.I.A. 2__________________________ [Disabled]
    System Memory Multiplier (SPD)____ [2.00]
    DRAM Timing Selectable_______ SPD __ [Manual]
    
    Performance Enhance = [Standard]
    
    CAS Latency Time________________ ?
    Dram RAS# to CAS# Delay_________ ?
    Dram RAS# Precharge Delay_______?
    Precharge Delay (tRAS)__________ ?
    
    ACT to ACT Delay (tRRD)_________ ?
    Rank Write to READ Delay________ ?
    Write to Precharge Delay_________ ?
    Refresh to ACT Delay______________ ?
    Read to Precharge Delay__________ ?
    Static tRead Value_______________
    Static tRead Phase Adjust________ [Auto]
    
    System Voltage Control____ [Manual]
    DDR2 OverVoltage Control__ [+0.300V] 
    PCI-E OverVoltage Control_ [+0.1V] 
    FSB OverVoltage Control___ [+0.1V] 
    (G)MCH OverVoltage Control [+0.1V] 
    CPU Voltage Control_______ [1.25]
    
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC
    
    Integrated Peripherals
    Legacy USB Storage Detect___________________[Disabled] *Note* Must be enabled to flash from USB

  3. #3
    Join Date
    Oct 2008
    Posts
    2

    Default Re: GA-X48T-DQ6 + 4x OCZ3G13332GK = BSOD

    thank you very much for your reply!
    for the moment, I have replaced the board & memory with a GA-X48-DS5.
    as soon as my second processor has arrived, I will re-test the memory AND will send you my bios settings.

    grtz

    datcom

  4. #4
    Join Date
    Oct 2008
    Posts
    10

    Default Re: GA-X48T-DQ6 + 4x OCZ3G13332GK = BSOD

    I'm no expert but I have had major issues with OCZ memory on my EP45-UD3P - I could not get mine to boot with 2 2GB sticks installed. I finally resorted to taking one stick out and running with 2 GB until my replacement Mushkin sticks arrive. If you search around this forum and others, you'll find that I'm not the only one with OCZ+Gigabyte problems.

    If you have the option to return your RAM, you might want to do so and go with a brand that tends to work better with Gigabyte boards, like Mushkin or G.Skill. Just a thought.

  5. #5
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: GA-X48T-DQ6 + 4x OCZ3G13332GK = BSOD

    @ Avatar
    2x2GB needs several adjustments. You did set those right? I do belive you are right about it though, just wanted to check. My request for testing Samples from OCZ have been ignored so...... Thats all I can really say "For Sure" as I have not used them.

    *Side Note* Other companies have been more then willing to help with samples for testing, But OCZ has not answered me AT ALL and I sent a rquest to 3 different Emails. I expected at least a No maybe, but to be ignore is just VERY unprofessional from a company in my point of view.

    Several other companies were more then happy to offer samples, and answered me the very next day, some the same day within minutes.

    @ Datcom

    Post back if you have issues, I can help

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •