Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Results 1 to 4 of 4

Thread: Overclocking a EP45-DS3R + E8400




  1. #1
    Join Date
    Oct 2008
    Posts
    2

    Lightbulb Overclocking a EP45-DS3R + E8400

    Hiya! I am new to overclocking and found this thread to help me OC my proc.
    http://forums.tweaktown.com/f69/giga...locking-28257/
    I used the second poster's settings to put my proc at 3.6ghz.

    I have an issue though... My system config is:
    EP45-DS3R + E8400
    Zalman 9700 NT cooler
    4gb (2x2 kit) of Patriot DDR2 PC8500 @ cas5 timings and 1066mhz
    ATI DIAMOND RADEON HD4870 1GB GDDR5
    WD 320GB SATA Drive
    Antec 1200 Gaming Case
    700Watt Zalman PSU

    Is there any way to get a tighterOC for my system specs? I mean, can i get my memory to 1066 (instead of 800 like the directions)
    And also, When i check my system specs, it reports E8400 @ 3.0ghz, and 3.6ghz.... does this mean i only OCed 1 core?
    Thanx for your time guyz, and i hope i'm not asking too much!!

  2. #2
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Overclocking a EP45-DS3R + E8400

    Please post YOUR full settings you are using and I will advise back.

    Check with CPU-z for what speed your CPU is running, in the "Core Speed" box. CPU-z and some other apps will show 3.00 and 3.60 (3.00 in certain places Just means that 3.00 is stock)

    This is Just a template I use to ask people their settings, pay no attention to the numbers in it, replace with yours

    Code:
    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: 
    CPU Clock Ratio ..........................: 
    Fine CPU Clock Ratio.....................:.0
    CPU Frequency ...........................: 
    
    
    Clock Chip Control 
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled] 
    CPU Host Frequency (Mhz) ............: Mhz
    PCI Express Frequency (Mhz) .........:Set to 100
    
    C.I.A.2 .................................:[Disabled]
    
    
    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 
    PCI Express Clock Drive.................: <<< 
    CPU Clock Skew (ps)....................: <<< 
    MCH Clock Skew (ps)...................: <<< 
    
    
    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: [Auto]
    System Memory Multiplier ..............: 
    Memory Frequency (Mhz) ..............: 
    DRAM Timing Selectable ................: [Manual]
    
    Standard Timing Control
    CAS Latency Time........................
    tRCD .........................................
    tRP'...........................................
    tRAS..........................................
    
    Advanced Timing Control
    tRRD...........................................
    tWTR..........................................
    tWR............................................
    tRFC...........................................
    tRTP...........................................
    Command Rate (CMD) ....................:2
    
    Driving Strength Profiles
    Driving Strength ............................
    
    Channel A
    Static tRead Value.........................:7-10
     tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
     tRD Phase2 Adjustment .................:Auto
     tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 
    Twr2wr(Different Rank)...................:Auto 
    Twr2rd(Different Rank)...................:Auto 
    Trd2wr(Same/Diff Rank)..................:Auto 
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
    
    Channel B
    Static tRead Value.........................:7-10
     tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
     tRD Phase2 Adjustment .................:Auto
     tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 
    Twr2wr(Different Rank)...................:Auto 
    Twr2rd(Different Rank)...................:Auto 
    Trd2wr(Same/Diff Rank)..................:Auto 
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
    
    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................:
    CPU Termination…..... 1.200V*.......: <<< Leave
    CPU PLL…………………....1.500V*.......: <<< Leave
    CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above)
    CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above)
    
    MCH/ICH
    MCH Core…………….....1.100V...........: << 
    MCH Reference….…….0.800V...........; <<< Leave
    MCH/DRAM Ref.…......0.900V...........: <<< Leave
    ICH I/O……………….....1.550V............: <<< Leave
    ICH Core…………...……1.100V............: <<< Leave
    
    DRAM
    DRAM Voltage ……....1.800V............: 
    DRAM Termination .…0.900V............: <<< Leave
    Channel A Reference 0.900V............: <<< Leave
    Channel B Reference 0.900V............: <<< Leave
    
    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC
    
    Integrated Peripherals
    Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB

  3. #3
    Join Date
    Oct 2008
    Posts
    2

    Default Re: Overclocking a EP45-DS3R + E8400

    Thank you! As it turns out, you were right about windows displaying the original clock, and then the OC speed. CPU-Z clearz alot up.
    As for my exact settings, i used these recommended settings you gave for the same proc OC on the article i linked in my first post.


    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Fast
    CPU Clock Ratio ..........................: 9
    Fine CPU Clock Ratio.....................:.0
    CPU Frequency ...........................: 4.05


    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled]
    CPU Host Frequency (Mhz) ............: 450Mhz
    PCI Express Frequency (Mhz) .........:Set to 100

    C.I.A.2 .................................:[Disabled]


    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 800
    PCI Express Clock Drive.................: <<< 900
    CPU Clock Skew (ps)....................: <<< 50
    MCH Clock Skew (ps)...................: <<< 100-150


    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: [400]
    System Memory Multiplier ..............: 2.00
    Memory Frequency (Mhz) ..............: 900
    DRAM Timing Selectable ................: [Manual]

    Standard Timing Control
    CAS Latency Time........................5
    tRCD .........................................5
    tRP'...........................................5
    tRAS..........................................15/18

    Advanced Timing Control
    tRRD...........................................3-5
    tWTR..........................................3-6 (May need 14 to boot first time)
    tWR............................................4-6 (May need 14 to boot first time)
    tRFC...........................................52-62
    tRTP...........................................3-5
    Command Rate (CMD) ....................:2

    Driving Strength Profiles
    Driving Strength ............................1066-1200 (1200 may be best)

    Channel A
    Static tRead Value.........................:8-10
    tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Channel B
    Static tRead Value.........................:8-10
    tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................: << All up to your chip. If you know what voltage you need great, this board I think is about .6 or so less for actual vs what you set in the BIOS

    CPU Termination…..... 1.200V*.......: <<< 1.25-1.35
    CPU PLL…………………....1.500V*.......: <<< 1.5
    CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above)
    CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above)

    MCH/ICH
    MCH Core…………….....1.100V...........: << 1.2-1.3
    MCH Reference….…….0.800V...........; <<< Leave
    MCH/DRAM Ref.…......0.900V...........: <<< Leave
    ICH I/O……………….....1.550V............: <<< Leave
    ICH Core…………...……1.100V............: <<< Leave

    DRAM
    DRAM Voltage ……....1.800V............: 2.1
    DRAM Termination .…0.900V............: <<< Leave
    Channel A Reference 0.900V............: <<< Leave
    Channel B Reference 0.900V............: <<< Leave

    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC

    </pre>
    I put the vcore to around 1.32 is the only exception, and on the fields with ranges #-#, i went with close to the highest range. But my memory is working at 800mhz... I wonder if it will be stable for 1066mhz like it is rated for? Tnx!

  4. #4
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Overclocking a EP45-DS3R + E8400

    Though that may be it. Please post me your exact Settings so I can better advise

    But for now, I can say you will have to run a higher or lower FSB to get 1066. You can try this but it may not boot or be stable (Not because of the speed, but the strap used) >>>
    (G)MCH Frequency Latch...............: [333]
    System Memory Multiplier ..............: 3.20
    Memory Frequency (Mhz) ..............: 1080

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •