Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 1 of 3 123 LastLast
Results 1 to 10 of 24

Thread: EP45-DQ6 Overclocking Newbie




  1. #1
    Join Date
    Sep 2008
    Posts
    12

    Default EP45-DQ6 Overclocking Newbie

    I purchased my EP45-DQ6 last month to essentially build a new system upon some existing components I had from an older system. I retained only the SATA internal hard drives, original Antec case and other external components (monitors) from the old system a replaced the motherboard (model mentioned above), an Intel Q9450 quad core cpu, memory (OCZ OCZ2RPR8004GK 4GB PC2-6400 (DDR2-800)), video card (ASUS EAH4850) and power supply (Antec Truepower Trio 550). I also replaced my Haupaugge PVR150 with a HVR-8500, but that is not the isue here.

    I have never really trie to overclock my prior systems event though the motherboards I have owned have all touted this ability. I simply have never been able to figure out the suttle nuances of overclocking with any success. Take my attepts here for example. I have applied the following settings on a system running the AWARD BIOS F10.

    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Turbo
    CPU Clock Ratio ..........................: 8x
    Fine CPU Clock Ratio.....................:+0.0
    CPU Frequency ...........................: 2.6 (333x8)


    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Disabled]
    CPU Host Frequency (Mhz) ............: 333 Mhz
    PCI Express Frequency (Mhz) .........:100


    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: 800 mV
    PCI Express Clock Drive.................: 900 mV
    CPU Clock Skew (ps)....................: 0 ps
    MCH Clock Skew (ps)...................: 0 ps


    DRAM Performance Control
    Performance Enhance...................: [Extreme]
    Extreme Memory Profile (X.M.P.).....: Auto
    (G)MCH Frequency Latch...............: 333
    System Memory Multiplier ..............: Auto
    Memory Frequency (Mhz) ..............: 1066
    DRAM Timing Selectable ................: [Manual]

    Standard Timing Control
    CAS Latency Time........................5
    tRCD ......................................... 5
    tRP'...........................................5
    tRAS..........................................15

    Advanced Timing Control
    tRRD...........................................3
    tWTR..........................................3
    tWR............................................5
    tRFC...........................................50
    tRTP...........................................3
    Command Rate (CMD) ....................:2

    Channel A
    Static tRead Value.........................:7
    tRD Phase0 Adjustment...................:Auto (reads as 0)
    tRD Phase1 Adjustment...................:Auto (reads as 0)
    tRD Phase2 Adjustment .................:Auto (reads as 0)
    tRD Phase3 Adjustment..................:Auto (reads as 0)
    Trd2rd(Different Rank)....................:Auto (reads as 8)
    Twr2wr(Different Rank)...................:Auto (reads as 8)
    Twr2rd(Different Rank)...................:Auto (reads as 7)
    Trd2wr(Same/Diff Rank)..................:Auto (reads as 9)
    Dimm1 Clock Skew Control...............:Auto
    Dimm2 Clock Skew Control...............:Auto

    Channel B
    Static tRead Value.........................:7
    tRD Phase0 Adjustment...................:Auto (reads as 0)
    tRD Phase1 Adjustment...................:Auto(reads as 0)
    tRD Phase2 Adjustment .................:Auto (reads as 0)
    tRD Phase3 Adjustment..................:Auto (reads as 0)
    Trd2rd(Different Rank)....................:Auto (reads as 8)
    Twr2wr(Different Rank)...................:Auto (reads as 8)
    Twr2rd(Different Rank)...................:Auto (reads as 7)
    Trd2wr(Same/Diff Rank)..................:Auto (reads as 9)
    Dimm1 Clock Skew Control...............:Auto
    Dimm2 Clock Skew Control...............:Auto

    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................:1.27500
    CPU Termination…..... 1.200V*.......:Auto (reads as 1.2)
    CPU PLL…………………....1.500V*.......:Auto (reads as 1.5)
    CPU Referen.…………....0.755V*.......: Auto (reads as .76)
    CPU Reference2………,,0.800V*.......:Auto (reads as .8)

    MCH/ICH
    MCH Core…………….....1.100V...........: 1.2
    MCH Reference….…….0.800V...........; Auto (reads as .76)
    MCH/DRAM Ref.…......0.900V...........: Auto
    ICH I/O……………….....1.550V............: Auto (reads as 1.5)
    ICH Core…………...……1.100V............: not in bios

    DRAM
    DRAM Voltage ……....1.800V............:1.9600
    DRAM Termination .…0.900V............: auto
    Channel A Reference 0.900V............: auto
    Channel B Reference 0.900V............: auto



    I constantly get a screen pop up in M.I.T. section that said the system experienced a boot failure due to overclocking or voltage change and that last settings don't coincide with h/w states.

    There are obviously about 20 or 30 separate seeing, each of multiple possible values. I could either try out the hundreds of thousand of possible combinations of vaus to try and get this work, or I could humbly ask for assitnace from someone who knows a bit more about this and can guide me towards getting better value and performance from my newly built system. Also, please let me know if I can added any bad or poor performinig components.

    Any guidance, advice, or assitance than anyone can offer here would be greatly appreciated. Thanks in advance for your assistance.

    David

  2. #2
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: EP45-DQ6 Overclocking Newbie

    Well what speed do you want to try for is really the question. I do see several settings that if let would hold you back.

    Here try this for a 3.2 overclock >>>

    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............:Fast
    CPU Clock Ratio ..........................: 8x
    Fine CPU Clock Ratio.....................:+0.0
    CPU Frequency ...........................: 3.216 (402x8)


    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Disabled]
    CPU Host Frequency (Mhz) ............: 402 Mhz
    PCI Express Frequency (Mhz) .........:100


    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: 800 mV
    PCI Express Clock Drive.................: 900 mV
    CPU Clock Skew (ps)....................: 0 ps
    MCH Clock Skew (ps)...................: 50-150ps


    DRAM Performance Control
    Performance Enhance...................: [Standard]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: 400 (Set voltages, Static Tread and this and reboot then set the rest) Main thing is to set as little as you can with this. So you may also try Setting all ram timings to highest first and then reboot to make these changes.

    System Memory Multiplier ..............: 2.00 Or 2.66 (If you think you can run 1066 Ram speed with those sticks)

    Memory Frequency (Mhz) ..............: 800 or 1066 per above
    DRAM Timing Selectable ................: [Manual]

    Standard Timing Control
    CAS Latency Time........................5
    tRCD ......................................... 5
    tRP'...........................................5
    tRAS..........................................15/18

    Set all highest below, and later lower one at a time testing with memtest86+ as you go.

    Advanced Timing Control
    tRRD...........................................3-5
    tWTR..........................................3-6 (May need 12 for first boot thru after MCH change)

    tWR............................................4-6 (May need 14 for first boot thru after MCH change)
    tRFC...........................................50
    tRTP...........................................3-6
    Command Rate (CMD) ....................:2

    Channel A
    Static tRead Value.........................:8-12
    tRD Phase0 Adjustment...................:Auto (reads as 0)<< leave all below here on Auto, if they are set to a value then manually put them in Auto

    tRD Phase1 Adjustment...................:Auto (reads as 0)
    tRD Phase2 Adjustment .................:Auto (reads as 0)
    tRD Phase3 Adjustment..................:Auto (reads as 0)
    Trd2rd(Different Rank)....................:Auto (reads as 8)
    Twr2wr(Different Rank)...................:Auto (reads as 8)
    Twr2rd(Different Rank)...................:Auto (reads as 7)
    Trd2wr(Same/Diff Rank)..................:Auto (reads as 9)
    Dimm1 Clock Skew Control...............:Auto
    Dimm2 Clock Skew Control...............:Auto

    Channel B
    Static tRead Value.........................:8-12
    tRD Phase0 Adjustment...................:Auto (reads as 0) << leave all below here on Auto, if they are set to a value then manually put them in Auto

    tRD Phase1 Adjustment...................:Auto(reads as 0)
    tRD Phase2 Adjustment .................:Auto (reads as 0)
    tRD Phase3 Adjustment..................:Auto (reads as 0)
    Trd2rd(Different Rank)....................:Auto (reads as 8)
    Twr2wr(Different Rank)...................:Auto (reads as 8)
    Twr2rd(Different Rank)...................:Auto (reads as 7)
    Trd2wr(Same/Diff Rank)..................:Auto (reads as 9)
    Dimm1 Clock Skew Control...............:Auto
    Dimm2 Clock Skew Control...............:Auto

    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................:1.27500 << all up to your chip. Dont use Auto as it will set too much. Best to set high and then lower later. Stock may get you 3.2 but maybe not. And what you set here will be less in windows so keep this in mind and check to see the difference so you know what it is in CPU-z. Maybe 1.30-1.32 in the BIOS, likely will need less but maybe not all chips are different

    CPU Termination…..... 1.200V*.......:Auto (reads as 1.2) 1.2-1.3(likely not needed at all until 400-450+ FSB so you can leave on auto for now) Since I did list 400 FSb above, you may try 1.2-1.25 if you like.

    CPU PLL…………………....1.500V*.......:Auto (reads as 1.5)
    CPU Referen.…………....0.755V*.......: Auto (reads as .76)
    CPU Reference2………,,0.800V*.......:Auto (reads as .8)

    MCH/ICH
    MCH Core…………….....1.100V...........: 1.2-1.3 << Needed for 2x2GB
    MCH Reference….…….0.800V...........; Auto (reads as .76)
    MCH/DRAM Ref.…......0.900V...........: Auto
    ICH I/O……………….....1.550V............: Auto (reads as 1.5) If you want to set 1.5-1.6


    DRAM
    DRAM Voltage ……....1.800V............:1.9600 << 2.0 is good maybe (2.1 may be needed as 1.8 is too low and they have since updated the programming for the SPD settings of this ram) 2.1 would be needed likely to get the 1066 stable (if it will at all)

  3. #3
    Join Date
    Sep 2008
    Posts
    12

    Default Re: EP45-DQ6 Overclocking Newbie

    Thank you for the feedback. I have applies these settings you have provided all at once, but am still getting the red screen H/W settings message when I get back into the BIOS MIT settings.

    Let me clarify a couple of things you stated above to ensure that I understand. In the MCH Frequency Latch settings, you've indicated that voltages, ST and this (MCH?) should all be applied first. Do you mean to apply those settings alone before anything else, then reboot and apply the remaining settings you've provided? Also, the only way to change the CPU Host Requency is to Enable the CPU Host Clock Control, is this right?

    When I run SiSoftware Sandra after rebooting, I see no change in processor speed, or any other applicable setting for that matter. Did I miss something crucial in the instructions you provided above? I would like to understand the changes better, but still don't understand what I am changing and why.

    Thanks again for your assistance.

  4. #4
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: EP45-DQ6 Overclocking Newbie

    Yes, you can apply them all at once or as I suggested with as few as you can with MCH changes.

    Yes you must enabled CPU host clock control to change FSB

    When you get a triple reboot and see the red warning box in the BIOS all stock settings will be used, not what you set or see in the BIOS as it was wrong. Once you get a proper reboot (One or Two reboots) then see no warning in the BIOS you will know things are correct and applied

    If you were using all the highest settings I provided above then you likely still need more CPU vcore as those settings are loose and should not hold you back at all

  5. #5
    Join Date
    Sep 2008
    Posts
    12

    Default Re: EP45-DQ6 Overclocking Newbie

    I've updated the VCore settings as follows:

    CPU Vcore….……….........................:1.33125
    CPU Termination…..... 1.3V

    I still get a triple boot or perhaps quadruple boot and the red screen. The only setting that I have changed that I see reflected in Windows is the DRAM voltage of 2.1. Should I continue to bump up the CPU VCore settings or is there something else that needs be changed?

  6. #6
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: EP45-DQ6 Overclocking Newbie

    Yeah you may need far more voltage for your overclock as 1.33 is way less in windows (Check with CPU-z, but I guess it would have to be applied first to see the change so that may be of no help)

    Please do post me exactly what you are using now and I can try to help you further.

    1.36 may bee good in BIOS for about 1.30 in windows, if that does not get you thru then you have some other setting off. Let me see fully where you are at with settings and I will advise

  7. #7
    Join Date
    Sep 2008
    Posts
    12

    Default Re: EP45-DQ6 Overclocking Newbie

    Here are my complete current settings. So far, no change in results. Same as before.

    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............:Fast
    CPU Clock Ratio ..........................: 8x
    Fine CPU Clock Ratio.....................:+0.0
    CPU Frequency ...........................: 3.216 (402x8)

    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled]
    CPU Host Frequency (Mhz) ............: 402 Mhz
    PCI Express Frequency (Mhz) .........:100
    C.I.A.2........................................Dis abled

    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: 800 mV
    PCI Express Clock Drive.................: 900 mV
    CPU Clock Skew (ps)....................: 0 ps
    MCH Clock Skew (ps)...................: 50ps


    DRAM Performance Control
    Performance Enhance...................: [Standard]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: 400

    System Memory Multiplier ..............: 2.66

    Memory Frequency (Mhz) ..............: 800 or 1066 per above
    DRAM Timing Selectable ................: [Manual]

    Standard Timing Control
    CAS Latency Time........................5
    tRCD ......................................... 5
    tRP'...........................................5
    tRAS..........................................18

    Advanced Timing Control
    tRRD...........................................5
    tWTR..........................................12
    tWR............................................14
    tRFC...........................................50
    tRTP...........................................6
    Command Rate (CMD) ....................:2

    Channel A
    Static tRead Value.........................:12
    tRD Phase0 Adjustment...................:Auto (reads as 0)<< leave all below here on Auto, if they are set to a value then manually put them in Auto

    tRD Phase1 Adjustment...................:Auto (reads as 0)
    tRD Phase2 Adjustment .................:Auto (reads as 0)
    tRD Phase3 Adjustment..................:Auto (reads as 0)
    Trd2rd(Different Rank)....................:Auto (reads as 8)
    Twr2wr(Different Rank)...................:Auto (reads as 8)
    Twr2rd(Different Rank)...................:Auto (reads as 7)
    Trd2wr(Same/Diff Rank)..................:Auto (reads as 9)
    Dimm1 Clock Skew Control...............:Auto
    Dimm2 Clock Skew Control...............:Auto

    Channel B
    Static tRead Value.........................:12
    tRD Phase0 Adjustment...................:Auto (reads as 0) << leave all below here on Auto, if they are set to a value then manually put them in Auto

    tRD Phase1 Adjustment...................:Auto(reads as 0)
    tRD Phase2 Adjustment .................:Auto (reads as 0)
    tRD Phase3 Adjustment..................:Auto (reads as 0)
    Trd2rd(Different Rank)....................:Auto (reads as 8)
    Twr2wr(Different Rank)...................:Auto (reads as 8)
    Twr2rd(Different Rank)...................:Auto (reads as 7)
    Trd2wr(Same/Diff Rank)..................:Auto (reads as 9)
    Dimm1 Clock Skew Control...............:Auto
    Dimm2 Clock Skew Control...............:Auto

    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................:1.37500
    CPU Termination…..... 1.300V
    CPU PLL…………………....1.500V*.......:Auto (reads as 1.5)
    CPU Referen.…………....0.755V*.......: Auto (reads as .76)
    CPU Reference2………,,0.800V*.......:Auto (reads as .8)

    MCH/ICH
    MCH Core…………….....1.13
    MCH Reference….…….0.800V...........; Auto (reads as .76)
    MCH/DRAM Ref.…......0.900V...........: Auto
    ICH I/O……………….....1.550V............: Auto (reads as 1.5) If you want to set 1.5-1.6

    DRAM
    DRAM Voltage ……....2.1

  8. #8
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: EP45-DQ6 Overclocking Newbie

    Try this, I think you are trying to push that ram to far >>>

    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............:Fast
    CPU Clock Ratio ..........................: 8x
    Fine CPU Clock Ratio.....................:+0.0
    CPU Frequency ...........................: 3.216 (402x8)

    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled]
    CPU Host Frequency (Mhz) ............: 402 Mhz
    PCI Express Frequency (Mhz) .........:100
    C.I.A.2........................................Dis abled

    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: 800 mV
    PCI Express Clock Drive.................: 900 mV
    CPU Clock Skew (ps)....................: 0 ps
    MCH Clock Skew (ps)...................: 50ps


    DRAM Performance Control
    Performance Enhance...................: [Standard]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: 400

    System Memory Multiplier ..............: 2.00

    Memory Frequency (Mhz) ..............: 800
    DRAM Timing Selectable ................: [Manual]

    Standard Timing Control
    CAS Latency Time........................5
    tRCD ......................................... 5
    tRP'...........................................5
    tRAS..........................................18

    Advanced Timing Control
    tRRD...........................................5
    tWTR..........................................12
    tWR............................................14
    tRFC...........................................68
    tRTP...........................................6
    Command Rate (CMD) ....................:2

    Channel A
    Static tRead Value.........................:10
    tRD Phase0 Adjustment...................:Auto (reads as 0)<< leave all below here on Auto, if they are set to a value then manually put them in Auto

    tRD Phase1 Adjustment...................:Auto (reads as 0)
    tRD Phase2 Adjustment .................:Auto (reads as 0)
    tRD Phase3 Adjustment..................:Auto (reads as 0)
    Trd2rd(Different Rank)....................:Auto (reads as 8)
    Twr2wr(Different Rank)...................:Auto (reads as 8)
    Twr2rd(Different Rank)...................:Auto (reads as 7)
    Trd2wr(Same/Diff Rank)..................:Auto (reads as 9)
    Dimm1 Clock Skew Control...............:Auto
    Dimm2 Clock Skew Control...............:Auto

    Channel B
    Static tRead Value.........................:10
    tRD Phase0 Adjustment...................:Auto (reads as 0) << leave all below here on Auto, if they are set to a value then manually put them in Auto

    tRD Phase1 Adjustment...................:Auto(reads as 0)
    tRD Phase2 Adjustment .................:Auto (reads as 0)
    tRD Phase3 Adjustment..................:Auto (reads as 0)
    Trd2rd(Different Rank)....................:Auto (reads as 8) << When you say this, you do mean it is set in Auto right, but you see this value on the left? If so that is ok, but if it is Set as this that is not.

    Twr2wr(Different Rank)...................:Auto (reads as 8)
    Twr2rd(Different Rank)...................:Auto (reads as 7)
    Trd2wr(Same/Diff Rank)..................:Auto (reads as 9)
    Dimm1 Clock Skew Control...............:Auto
    Dimm2 Clock Skew Control...............:Auto

    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................:1.37500
    CPU Termination…..... 1.300V << Auto
    CPU PLL…………………....1.500V*.......:Auto (reads as 1.5) Set to stock
    CPU Referen.…………....0.755V*.......: Auto (reads as .76)
    CPU Reference2………,,0.800V*.......:Auto (reads as .8)

    MCH/ICH
    MCH Core…………….....1.13 << 1.2+
    MCH Reference….…….0.800V...........; Auto (reads as .76)
    MCH/DRAM Ref.…......0.900V...........: Auto
    ICH I/O……………….....1.550V............: Auto (reads as 1.5) If you want to set 1.5-1.6

    DRAM
    DRAM Voltage ……....2.1

  9. #9
    Join Date
    Sep 2008
    Posts
    12

    Default Re: EP45-DQ6 Overclocking Newbie

    I have applied the changes as described here...unfortunately no change in result. I do want to correct the memory specification I had originally provided. The memory I has is capable of 1066. I actual model of memory that I have is OCZ2RPR10664GK (OCZ Reaper HPC 4GB 2 X 2G).

    Are there any specific change I can toggle on my own, or "play with"? Are there any particular things that I should not do? I don't want to damage any of the components by settings something incorrectly.

  10. #10
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: EP45-DQ6 Overclocking Newbie

    Excessive voltage is really the only thing you do not want to do.

    For 1066 you would need to use this general area to get your ram speed up to that, same as above except the memory multi. If you are not getting the above to even load you likely need more CPU voltage for sure since those are 800 settings and if that is not booting for you then you are not using enough voltages somewhere >>>>

    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............:Fast
    CPU Clock Ratio ..........................: 8x
    Fine CPU Clock Ratio.....................:+0.0
    CPU Frequency ...........................: 3.216 (402x8)

    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled]
    CPU Host Frequency (Mhz) ............: 402 Mhz
    PCI Express Frequency (Mhz) .........:100
    C.I.A.2........................................Dis abled

    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: 800 mV
    PCI Express Clock Drive.................: 900 mV
    CPU Clock Skew (ps)....................: 0 ps
    MCH Clock Skew (ps)...................: 50ps


    DRAM Performance Control
    Performance Enhance...................: [Standard]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: 400

    System Memory Multiplier ..............: 2.66

    Memory Frequency (Mhz) ..............: 1069
    DRAM Timing Selectable ................: [Manual]

    Standard Timing Control
    CAS Latency Time........................5
    tRCD ......................................... 5
    tRP'...........................................5
    tRAS..........................................18

    Advanced Timing Control
    tRRD...........................................5
    tWTR..........................................12
    tWR............................................14
    tRFC...........................................68
    tRTP...........................................6
    Command Rate (CMD) ....................:2

    Channel A
    Static tRead Value.........................:10
    tRD Phase0 Adjustment...................:Auto (reads as 0)<< leave all below here on Auto, if they are set to a value then manually put them in Auto

    tRD Phase1 Adjustment...................:Auto (reads as 0)
    tRD Phase2 Adjustment .................:Auto (reads as 0)
    tRD Phase3 Adjustment..................:Auto (reads as 0)
    Trd2rd(Different Rank)....................:Auto (reads as 8)
    Twr2wr(Different Rank)...................:Auto (reads as 8)
    Twr2rd(Different Rank)...................:Auto (reads as 7)
    Trd2wr(Same/Diff Rank)..................:Auto (reads as 9)
    Dimm1 Clock Skew Control...............:Auto
    Dimm2 Clock Skew Control...............:Auto

    Channel B
    Static tRead Value.........................:10
    tRD Phase0 Adjustment...................:Auto (reads as 0) << leave all below here on Auto, if they are set to a value then manually put them in Auto

    tRD Phase1 Adjustment...................:Auto(reads as 0)
    tRD Phase2 Adjustment .................:Auto (reads as 0)
    tRD Phase3 Adjustment..................:Auto (reads as 0)
    Trd2rd(Different Rank)....................:Auto (reads as 8) << When you say this, you do mean it is set in Auto right, but you see this value on the left? If so that is ok, but if it is Set as this that is not.

    Twr2wr(Different Rank)...................:Auto (reads as 8)
    Twr2rd(Different Rank)...................:Auto (reads as 7)
    Trd2wr(Same/Diff Rank)..................:Auto (reads as 9)
    Dimm1 Clock Skew Control...............:Auto
    Dimm2 Clock Skew Control...............:Auto

    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................:1.37500 (What do you get in windows at any voltge you can set and boot at? You will need to keep that in mind, It may be .6 or more less then you set in the BIOS. Meaning this 1.375 may only be 1.31 or less. So you may still need more

    CPU Termination…..... 1.300V << Auto
    CPU PLL…………………....1.500V*.......:Auto (reads as 1.5) Set to stock
    CPU Referen.…………....0.755V*.......: Auto (reads as .76)
    CPU Reference2………,,0.800V*.......:Auto (reads as .8)

    MCH/ICH
    MCH Core…………….....1.13 << 1.2+ (Try 1.24 or 1.26)
    MCH Reference….…….0.800V...........; Auto (reads as .76)
    MCH/DRAM Ref.…......0.900V...........: Auto
    ICH I/O……………….....1.550V............: Auto (reads as 1.5) If you want to set 1.5-1.6

    DRAM
    DRAM Voltage ……....2.1

Page 1 of 3 123 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •