Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 2 of 2 FirstFirst 12
Results 11 to 13 of 13

Thread: I hit the wall at 3.0GHz w/EP45DS3R/Q6600




  1. #11
    Join Date
    Sep 2008
    Location
    ATL
    Posts
    10

    Default Re: I hit the wall at 3.0GHz w/EP45DS3R/Q6600

    Hey LSDMEASAP. Good morning.

    I actually made pretty good progress overnight. I started with your suggestions above and loosened the timings. Right now I have it running at 407x8 = 3.256 GHz. After 10 passes, I have 9 errors, all on test 7. No errors until pass 3, roughly 1 hour plus into testing

    However, in testing on stick of RAM at a time, noticed this rig is much more stable albeit slower with only 1 stick of RAM. More MCH voltage required?

    I'm still thinking heat may be an issue, so looking to pick up a couple small fans this morning. Regardless, if I can get this thing stable, looking to lap the CPU and reseat the cooler. 3.2 or above gets too hot.

    I will post the setting later this morning as I did add a little V MCH and am retesting

  2. #12
    Join Date
    Sep 2008
    Location
    ATL
    Posts
    10

    Default Re: I hit the wall at 3.0GHz w/EP45DS3R/Q6600

    Current settings:

    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Auto
    CPU Clock Ratio ..........................: 8
    CPU Frequency ...........................: 3.256GHz (407x8)


    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled]
    CPU Host Frequency (Mhz) ............: 407 Mhz
    PCI Express Frequency (Mhz) .....: 100
    C.I.A.2.......................................: Disabled

    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< Stock
    PCI Express Clock Drive.................: <<< Stock
    CPU Clock Skew (ps)....................: <<< 100
    MCH Clock Skew (ps)...................: <<< 150


    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: 400MHz
    System Memory Multiplier ..............: 2.00B
    Memory Frequency (Mhz) ..............: 800
    DRAM Timing Selectable ................: [Manual]

    Corsair 4-4-4-12 2.1 Standard 2x2GB in slot 0 and 2
    CAS LatencyTime........................:5
    RCD .........................................:6
    tRP...........................................:6
    tRAS..........................................:22

    Set to all highest first

    Advanced Timing Control
    tRRD...........................................5
    tWTR..........................................4
    tWR............................................6
    tRFC...........................................62
    tRTP...........................................5
    Command Rate (CMD) ....................2

    Driving strength Profiles............1066 Mhz

    Channel A
    Static tRead Value.........................:10
    tRD Phase0 Adjustment...................:0-Normal
    tRD Phase1 Adjustment...................:0 AUTO
    tRD Phase2 Adjustment ..................:0 AUTO
    tRD Phase3 Adjustment...................:0 AUTO
    Trd2rd(Different Rank)....................:6 AUTO
    Twr2wr(Different Rank)...................:6 AUTO
    Twr2rd(Different Rank)...................:5 AUTO
    rd2wr(Same/Diff Rank)..................:8 AUTO
    imm1 Clock Skew Control...............: AUTO
    Dimm2 Clock Skew Control...............: AUTO

    Channel B
    Static tRead Value.........................:10
    RD Phase0 Adjustment...................:0-Normal
    RD Phase1 Adjustment...................:0 AUTO
    tRD Phase2 Adjustment .................:0 AUTO
    tRD Phase3 Adjustment..................:0 AUTO
    Trd2rd(Different Rank)....................:6 AUTO
    Twr2wr(Different Rank)...................:6 AUTO
    wr2rd(Different Rank)...................:5 AUTO
    rd2wr(Same/Diff Rank)..................:8 AUTO

    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................:1.4825

    CPUTermination.…..... 1.200V*.......: 1.450
    CPU PLL…………………....1.500V*.......: 1.500
    CPU Referen.…………....0.755V*.......: AUTO
    CPU Reference2………,,0.800V*.......: AUTO

    MCH/ICH
    MCH Core…………….....1.100V...........:1.3
    MCH Reference….…….0.800V...........: AUTO
    MCH/DRAM Ref.…......0.900V...........: 1.000
    ICH I/O……………….....1.550V............: AUTO

    DRAM
    DRAM Voltage ……....1.800V............: 2.140
    DRAM Termination .…0.900V............: AUTO
    Channel A Reference 0.900V............: AUTO
    Channel B Reference 0.900V............: AUTO

    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled]<!-- / message --><!-- sig -->
    Last edited by dtfeld; 11-11-2008 at 10:47 PM.

  3. #13
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: I hit the wall at 3.0GHz w/EP45DS3R/Q6600

    Ya, one stick will always be more stable then two. So... Each stick for sure passes by itself right? Just checking, they should

    And ya, more or less MCH helps sometimes. All depends on other settings, so always test less as well

    You should try much less Vtt, like maybe 1.3-1.35 or even less.
    Did you test out 444-12 yet again? If you do and it fails try setting driving strength profile to 800

    Then you can get the rest of those timings lowered a bit. Please do fix this >>>

    Channel A & B
    RD Phase0 Adjustment...................:0-Normal << Should be Auto

Page 2 of 2 FirstFirst 12

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •