Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 1 of 11 123 ... LastLast
Results 1 to 10 of 106

Thread: ddr-2 1300 mghz




  1. #1
    Join Date
    Oct 2008
    Location
    CA
    Posts
    215

    Smile ddr-2 1300 mghz

    Looking for general settings for my bios. Here is what i want to achieve, i have a ep45-ds3r, i want to run my e8500 around 3.6 gz i have some ddr-2 1300 mghz it dont run stock at that, but it comes as ddr-2 1300, and will run well past that, it runs on 2.35 to 2.45 volts, so i want about 3.6 processor, and around 1300 plus on my memory, it runs at 5-5-5-12to15, thanks again for all your help, this is a awesome forum.

    mike

  2. #2
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: ddr-2 1300 mghz

    Please do post me a link to you ram if you dont mind. Thanks

    Here, try this for 3.6 (CPU voltage as you know will be up to you and your Chip to find)

    This is Just a template I use to ask people their settings, pay no attention to the numbers in it, replace with yours

    Code:
    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............:Fast
    CPU Clock Ratio ..........................: 9
    Fine CPU Clock Ratio.....................:.0
    CPU Frequency ...........................: 3.618 Ghz
    
    
    Clock Chip Control 
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled] 
    CPU Host Frequency (Mhz) ............: 402Mhz
    PCI Express Frequency (Mhz) .........:Set to 100
    
    C.I.A.2 .................................:[Disabled]
    
    
    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 
    PCI Express Clock Drive.................: <<< 
    CPU Clock Skew (ps)....................: <<< 
    MCH Clock Skew (ps)...................: <<< 
    
    
    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: [400]
    System Memory Multiplier ..............: 3.33
    Memory Frequency (Mhz) ..............: 1338Mhz
    DRAM Timing Selectable ................: [Manual]
    
    Standard Timing Control
    CAS Latency Time........................5/6
    tRCD .........................................5/6
    tRP'...........................................5/6
    tRAS..........................................15/18
    
    Set all highest first then lower later testing with memtest86+ as you go
    
    Advanced Timing Control
    tRRD...........................................3-7
    tWTR..........................................4-8 (May need/should set 14-16 first)
    tWR............................................6-8 (May need/should set 16-18 first)
    tRFC...........................................42-58 (For 4GB 62-75/80)
    tRTP...........................................3-7
    Command Rate (CMD) ....................:2
    
    Driving Strength Profiles
    Driving Strength ............................1200 or 1333 (Higher then ram speed is normally best, so you may want to or need to use the one above 1333 (Sorry, cant remember if there is one or not?)
    
    Channel A
    Static tRead Value.........................:8-12
     tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
     tRD Phase2 Adjustment .................:Auto
     tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 
    Twr2wr(Different Rank)...................:Auto 
    Twr2rd(Different Rank)...................:Auto 
    Trd2wr(Same/Diff Rank)..................:Auto 
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
    
    Channel B
    Static tRead Value.........................:8-12
     tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
     tRD Phase2 Adjustment .................:Auto
     tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 
    Twr2wr(Different Rank)...................:Auto 
    Twr2rd(Different Rank)...................:Auto 
    Trd2wr(Same/Diff Rank)..................:Auto 
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
    
    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................: All up to you and your chip to find, set high first though so you know it is not the issue when you try to boot.  I would think maybe 1.35 or so in the BIOS for 1.29-1.3 Actual might work
    
    CPU Termination…..... 1.200V*.......: <<< 1.2-1.3
    CPU PLL…………………....1.500V*.......: <<< Set to Stock
    CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly 
    
    CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above)Auto Will set this correctly 
    
    MCH/ICH
    MCH Core…………….....1.100V...........: << 1.2-1.25 for stability (1.2-1.3 for 4GB) << may need more for either ram amount at those speeds, do not set above 1.38
    
    MCH Reference….…….0.800V...........; <<< Leave
    MCH/DRAM Ref.…......0.900V...........: <<< Leave
    ICH I/O……………….....1.550V............: <<< 1.5-1.65
    ICH Core…………...……1.100V............: <<<1.1-1.3
    
    DRAM
    DRAM Voltage ……....1.800V............: 2.1-?  Up to you and your ram's warranty 2.2 may be fine for that speed, but you did not link your ram so not really sure what it needs for what speeds.
    
    DRAM Termination .…0.900V............: <<< Leave
    Channel A Reference 0.900V............: <<< Leave
    Channel B Reference 0.900V............: <<< Leave
    
    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC
    
    Integrated Peripherals
    Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB

  3. #3
    Join Date
    Oct 2008
    Location
    CA
    Posts
    215

    Default Re: ddr-2 1300 mghz

    Here is the link to my ram, it takes overclocking to get it to 1300, but i have seen plenty of people going way past 1300 with it at 5-5-5-15, 2GB Team DDR2-1300 PC2-10400 dual channel memory kit

  4. #4
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: ddr-2 1300 mghz

    What you see someone else do with ram cannot be expected of your ram, keep that in mind for all hardware.

    So did the above settings help you get going any?

  5. #5
    Join Date
    Oct 2008
    Location
    CA
    Posts
    215

    Default Re: ddr-2 1300 mghz

    will try later today, thanks again, will keep your posted.

  6. #6
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

  7. #7
    Join Date
    Oct 2008
    Location
    CA
    Posts
    215

    Default Re: ddr-2 1300 mghz

    sorry took me so long, i have just started testing, got to 1300 no problem, with about 380 fsb, but when i raise the front side bus above 400, wont run, trying some tweaks now, will back soon .

  8. #8
    Join Date
    Oct 2008
    Location
    CA
    Posts
    215

    Default Re: ddr-2 1300 mghz

    Ok it works at the setting you gave me, now i would like to get to 475-480 fsb and try to be stable, if i go over the 401 you gave me, i get blue screens, so based on the setting you gave me, what should i do to get more fsb stable ?

  9. #9
    Join Date
    Oct 2008
    Location
    CA
    Posts
    215

    Default Re: ddr-2 1300 mghz

    Dont understand, board just wont post over 405 fsb . I can get the memory to run at 1467, but cant get the fsb over 405 ???

  10. #10
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: ddr-2 1300 mghz

    You cannot push your ram that hard is why 405+ FSB is failing for you, back off the memory multi and increase the FSB while you add voltage is all you need to do. You should have all memory timings loose and the speed set low while you try to find the high FSB you want, then set the ram later

Page 1 of 11 123 ... LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •