Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 2 of 6 FirstFirst 1234 ... LastLast
Results 11 to 20 of 53

Thread: GA-EP45-UD3P and 8 gig Corsair dominator 4x2gig 8500C5DF




  1. #11

    Default Re: GA-EP45-UD3P and 8 gig Corsair dominator 4x2gig 8500C5DF

    hehehehe .. only take me 10 min to get new CPU .... in that case .. i will go to the store ... if they have the E0 in stock ,,, put one on hold then go home take out CPU ... just hate the part take everything apart ... in that case .. will just run my memtest tonight just incase i return my CPU tomorrow ... did run with 2 pass ok on 4 ram install already before i start OC ... once again thanks and will keep you update ..

  2. #12
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: GA-EP45-UD3P and 8 gig Corsair dominator 4x2gig 8500C5DF

    10 minutes for a new CPU?

    Ahh so you think they will exchange it for you easy then? If so, great ya go grab ya a E0 just dont be surprised if it has 1-4 stuck sensors as well

  3. #13

    Default Re: GA-EP45-UD3P and 8 gig Corsair dominator 4x2gig 8500C5DF

    yep ... actually only 1min 25 second .. time it myself..... hehehehe ... got my E0 .. and the vid is lower .. from 1.250 to 1.2125 .... and have to lower my vcore voltage on my OC ... hehehe .. this is a much much better chip .... the funny thing the same core is stuck .. maybe the motherboard not the CPU ... and run about 10 degree cooler .. WOW

    quick question
    No-Execute Memory Protect............: [Enabled] ??

    is this to protect memory ? and this what happen when OC bad ... need to take out and have only 1 ram before i can go back into Cmost .. if not the computer also reboot endlessly and beep all over the place.

    here is the pic of some crazzy temp on air ... 3.8 at 50 degree only 1.38125 Vcore .. never seen this on air and idle only 27 ... this CPU is good ...i was so worries that the motherboard report wrong

    [/URL]
    Last edited by godto; 11-09-2008 at 12:49 PM.

  4. #14
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: GA-EP45-UD3P and 8 gig Corsair dominator 4x2gig 8500C5DF

    Nice!

    Ya, I use that enabled with no issues. No it is to protect your system from certain types of viruses

    That is good temps!

    Beeping all over eh, sounds like bad ram or Strap or voltages to me. If you still keep having issues post me what you are using that fails and I will try to help you out

    Ohh, same stuck sensor! Ahh, well at least it was not all of them. It's the CPU for sure not the board

  5. #15

    Default Re: GA-EP45-UD3P and 8 gig Corsair dominator 4x2gig 8500C5DF

    i'm able to get my 3.8 stable ... but my voltage is 1.38125 ...

    as i read many many place ...

    seem like the CPU termination = front side bus voltage ??? ... mine is at 1.22 most peoples i see at 1.3 - to 1.34 for ..4Ghz
    and also what is CPU PLL ??

    is that meant if i raise my CPU Termination then i can lower my Vcore ??
    i seen peoples with 3.8 only run about 1.3 vcore but higher CPU Termination

    will post my full spect tomorrow ... in between stress test now .. hehehehe ...

  6. #16
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: GA-EP45-UD3P and 8 gig Corsair dominator 4x2gig 8500C5DF

    Thats 1.38.. in the BIOS right? What it is in windows?

    Yes, vtt is same as FSB on other boards.

    PLL is phase-locked loop.

    Here is a little reading on this >>>

    Phase-locked loop - Wikipedia, the free encyclopedia
    Phase-Locked Loop Tutorial, PLL
    Introduction to the phase-locked loop (PLL)

    Yes, you may be able to lower vcore with more Vtt. But you are already using a low vcore so maybe not

    Not all chips are the same, so what you see someone else use does not apply. And your 1.38 is likely about 1.32 actual. Have you checked with CPU-z to see what you are actually using?

  7. #17

    Default Re: GA-EP45-UD3P and 8 gig Corsair dominator 4x2gig 8500C5DF

    more question ofcourse .. was wonder what to set for this

    CPU Vcore….………......1.2120V*.....:1.38125
    CPU Termination…..... 1.200V*.......: 1.240
    CPU PLL…………………....1.500V*.......: << Please set to stock, Auto overvolts this way to much


    what this number should be ??? my vcore ?? i have my set for 1.590 .. this seem like a magic number for lot of peoples OC to 3.8-4.2

  8. #18
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: GA-EP45-UD3P and 8 gig Corsair dominator 4x2gig 8500C5DF

    If you are asking about PLL, I assume. I say stock for sure which is 1.5, but you can try 1.56-1.59 if you like but it is not really needed with 45nm CPU's as much as it used to be for 65Nm

  9. #19

    Default Re: GA-EP45-UD3P and 8 gig Corsair dominator 4x2gig 8500C5DF

    okie .. here is my spec. ... 450x8.5 = 3.82GHz .. 8 gigs of ram

    everything run stable pass thru all the test
    10 hours on prime95 - small
    8 hours on prime95 blend
    8 hours on prime95 large
    4 hours on OCCT mix
    4 hours on OCCT ram
    4 hours on OCCT CPU
    5 pass on memtest86+ ... 15 pass on #5
    memtest exe. pass on 400% .. 8 hours or so
    coredamage - 3 hours
    intell burning test 20 pass
    Linx - 5 pass on max Ram .. 4 hours

    i about throw everything at it to make sure it's very very stable ... hehehehe
    on memtest did have to up the VTT to 1.28 from 1.26 to make it stable (crash once)

    what can i tweak to make thing run better ??? ram timming ?? or any voltage ? .. feel free to add and sugest ... and when i'm done with this setting ... probably burn in about a week or 2 .. i will start to OC to 4GHz ... but want to have a stable point just incase i can't .... the temp right now even with intell burntest and core damage i still only about 51-55 max on temp .. have a long way to go ... max temp i would ever go to is 64-65 ... still below damage level .. and i will never get that high on everyday use.

    Code:
    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ............:  Auto
    CPU Clock Ratio .......................:  8
    Fine CPU Clock Ratio..................:  0.5
    CPU Frequency ........................:  3.82 GHz  (450x8.5)
    
    Standard Clock Control
    CPU Host Clock Control.................: Enabled
    CPU Host Frequency (Mhz) ............: 450
    PCI Express Frequency (Mhz) .........: 100
    C.I.A.2 ...................................:[Disabled]
    
    Advanced Clock Control [Press Enter]
    CPU Clock Drive.........................: 800mV
    PCI Express Clock Drive...............: 900mV
    CPU Clock Skew (ps)............ 0ps...: 50ps
    MCH Clock Skew (ps)........... 0ps...: 150ps
    
    DRAM Performance Control
    Performance Enhance......................: Standard
    Extreme Memory Profile (X.M.P.)......: Disabled
    (G)MCH Frequency Latch..................: 400
    System Memory Multiplier ..............: 2.00D
    Memory Frequency (Mhz) .........1066..: 900
    DRAM Timing Selectable .................: Manual
    
    Standard Timing Control
    CAS Latency Time.....................5…:  5
    tRCD ...............................7 …:  5
    tRP'.................................7 …:  5 
    tRAS................................24…:   15
    
    Advanced Timing Control
    tRRD......................................4….:  (auto) 4  
    tWTR..................................... 4….:  (auto) 4
    tWR...................................... 8….:   (auto) 8
    tRFC.....................................68..:   (auto) 68
    tRTP...................................... 4…:   (auto) 4
    Command Rate (CMD) .......................0...:   (auto) 2
    
    Channel A Timing Settings
    Static tRead Value.........................: 11 (auto) 9
    tRD Phase0 Adjustment...................: 0 (auto)
    tRD Phase1 Adjustment...................: 0 (auto)
    tRD Phase2 Adjustment .................: 0 (auto)
    tRD Phase3 Adjustment..................: 0 (auto)
    Trd2rd(Different Rank)....................: 6 (auto)
    Twr2wr(Different Rank)...................: 6 (auto)
    Twr2rd(Different Rank)...................: 5 (auto)
    Trd2wr(Same/Diff Rank)..................: 8 (auto)
    Dimm1 Clock Skew Control...............: auto
    Dimm2 Clock Skew Control...............: auto
    DDR Write Training............................ auto
    
    Channel A Driving Settings
    x Driving Strength Profile.................... 1066
    x Data Driving Pull-Up Level.............. auto
    x Cmd Driving Pull-Up Level.............. auto
    x Ctrl Driving Pull-Up Level.............. auto
    x Clk Driving Pull-Up Level.............. auto
    
    x Data Driving Pull-Down Level.............. auto
    x Cmd Driving Pull-Down Level.............. auto
    x Ctrl Driving Pull-Down Level.............. auto
    x Clk Driving Pull-Down Level.............. auto
    
    Channel B Timing Settings
    Static tRead Value.........................: 11 (auto) 9
    tRD Phase0 Adjustment...................: 0 (auto)
    tRD Phase1 Adjustment...................: 0 (auto)
    tRD Phase2 Adjustment .................: 0 (auto)
    tRD Phase3 Adjustment..................: 0 (auto)
    Trd2rd(Different Rank)....................: 6 (auto)
    Twr2wr(Different Rank)...................: 6 (auto)
    Twr2rd(Different Rank)...................: 5 (auto)
    Trd2wr(Same/Diff Rank)..................: 8 (auto)
    Dimm1 Clock Skew Control...............: auto
    Dimm2 Clock Skew Control...............: auto
    DDR Write Training............................ auto
    
    
    Channel B Driving Settings
    x Driving Strength Profile.................... 1066
    x Data Driving Pull-Up Level.............. auto
    x Cmd Driving Pull-Up Level.............. auto
    x Ctrl Driving Pull-Up Level.............. auto
    x Clk Driving Pull-Up Level.............. auto
    
    x Data Driving Pull-Down Level.............. auto
    x Cmd Driving Pull-Down Level.............. auto
    x Ctrl Driving Pull-Down Level.............. auto
    x Clk Driving Pull-Down Level.............. auto
    
    Motherboard Voltage Control - CPU
    Load-Line Calibration ………………….:[Disabled]
    CPU Vcore….………......1.2120V......: 1.38125 V
    CPU Termination…..... 1.200V.......: 1.28 V
    CPU PLL…………………....1.500V.......: 1.500 V
    CPU Referen.…………....0.760V.......: [Auto]
    
    MCH/ICH
    MCH Core…………….....1.100V..........: .1.300 V
    MCH Reference….…….0.76V............: [Auto]
    MCH/DRAM Ref.…......0.900V...........: [Auto]
    ICH I/O……………….....1.500V............: 1.590 V
    ICH Core…………….....1.100V.............: 1.200 V
    DRAM
    DRAM Voltage ……....1.800V............:  2.08V
    DRAM Termination .…0.900V............: [Auto]
    Channel A Reference 0.900V............: [Auto]
    Channel B Reference 0.900V............: [Auto]
    
    Advanced Settings
    Limit CPUID Max. to 3...................: [Disabled]
    No-Execute Memory Protect.........: [Enabled]
    CPU Enhanced Halt (C1E)..............: [Disabled]
    C2/C2E State Support..................: [Disabled] 
    x C4/C4E State Support................: [Disabled]
    CPU Thermal Monitor 2(TM2) ........: [Enabled]
    CPU EIST Function.......................: [Disabled]
    Virtualization Technology...............: [Disabled]
    Last edited by godto; 11-14-2008 at 11:46 AM.

  10. #20
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: GA-EP45-UD3P and 8 gig Corsair dominator 4x2gig 8500C5DF

    WOW, thats alot of testing!!!!

    Is this the latest BIOS and did you load and apply/reboot optimized defaults after you flashed to it? If not you do need to, be sure you reboot BACK to the BIOS anytime you do that because you have to set your SATA Settings again

    You can try these changes >>>>

    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ............: Auto
    CPU Clock Ratio .......................: 8
    Fine CPU Clock Ratio..................: 0.5
    CPU Frequency ........................: 3.82 GHz (450x8.5)

    Standard Clock Control
    CPU Host Clock Control.................: Enabled
    CPU Host Frequency (Mhz) ............: 450
    PCI Express Frequency (Mhz) .........: 100
    C.I.A.2 ...................................:[Disabled]

    Advanced Clock Control [Press Enter]
    CPU Clock Drive.........................: 800mV
    PCI Express Clock Drive...............: 900mV
    CPU Clock Skew (ps)............ 0ps...: 50ps
    MCH Clock Skew (ps)........... 0ps...: 150ps

    DRAM Performance Control
    Performance Enhance......................: Standard
    Extreme Memory Profile (X.M.P.)......: Disabled
    (G)MCH Frequency Latch..................: 400
    System Memory Multiplier ..............: 2.00D
    Memory Frequency (Mhz) .........1066..: 900
    DRAM Timing Selectable .................: Manual

    Standard Timing Control
    CAS Latency Time.....................5…: 5
    tRCD ...............................7 …: 5 << Maybe 4
    tRP'.................................7 …: 5 << maybe 4
    tRAS................................24…: 15 << maybe 12 (These maybe's are only because you are underclocking the ram right now)

    Advanced Timing Control
    tRRD......................................4….: (auto) 4 << Try 3
    tWTR..................................... 4….: (auto) 4 << try 3
    tWR...................................... 8….: (auto) 8 << try 4-7
    tRFC.....................................68..: (auto) 68 << try 62-65
    tRTP...................................... 4…: (auto) 4 << Maybe 3
    Command Rate (CMD) .......................0...: (auto) 2

    Channel A Timing Settings
    Static tRead Value.........................: 11 (auto) 9
    tRD Phase0 Adjustment...................: 0 (auto)
    tRD Phase1 Adjustment...................: 0 (auto)
    tRD Phase2 Adjustment .................: 0 (auto)
    tRD Phase3 Adjustment..................: 0 (auto)
    Trd2rd(Different Rank)....................: 6 (auto)
    Twr2wr(Different Rank)...................: 6 (auto)
    Twr2rd(Different Rank)...................: 5 (auto)
    Trd2wr(Same/Diff Rank)..................: 8 (auto)
    Dimm1 Clock Skew Control...............: auto
    Dimm2 Clock Skew Control...............: auto
    DDR Write Training............................ auto

    Channel A Driving Settings
    x Driving Strength Profile.................... 1066
    x Data Driving Pull-Up Level.............. auto
    x Cmd Driving Pull-Up Level.............. auto
    x Ctrl Driving Pull-Up Level.............. auto
    x Clk Driving Pull-Up Level.............. auto

    x Data Driving Pull-Down Level.............. auto
    x Cmd Driving Pull-Down Level.............. auto
    x Ctrl Driving Pull-Down Level.............. auto
    x Clk Driving Pull-Down Level.............. auto

    Channel B Timing Settings
    Static tRead Value.........................: 11 (auto) 9
    tRD Phase0 Adjustment...................: 0 (auto)
    tRD Phase1 Adjustment...................: 0 (auto)
    tRD Phase2 Adjustment .................: 0 (auto)
    tRD Phase3 Adjustment..................: 0 (auto)
    Trd2rd(Different Rank)....................: 6 (auto)
    Twr2wr(Different Rank)...................: 6 (auto)
    Twr2rd(Different Rank)...................: 5 (auto)
    Trd2wr(Same/Diff Rank)..................: 8 (auto)
    Dimm1 Clock Skew Control...............: auto
    Dimm2 Clock Skew Control...............: auto
    DDR Write Training............................ auto


    Channel B Driving Settings
    x Driving Strength Profile.................... 1066
    x Data Driving Pull-Up Level.............. auto
    x Cmd Driving Pull-Up Level.............. auto
    x Ctrl Driving Pull-Up Level.............. auto
    x Clk Driving Pull-Up Level.............. auto

    x Data Driving Pull-Down Level.............. auto
    x Cmd Driving Pull-Down Level.............. auto
    x Ctrl Driving Pull-Down Level.............. auto
    x Clk Driving Pull-Down Level.............. auto

    Motherboard Voltage Control - CPU
    Load-Line Calibration ………………….:[Disabled]
    CPU Vcore….………......1.2120V......: 1.38125 V
    CPU Termination…..... 1.200V.......: 1.28 V
    CPU PLL…………………....1.500V.......: 1.500 V
    CPU Referen.…………....0.760V.......: [Auto]

    MCH/ICH
    MCH Core…………….....1.100V..........: .1.300 V << Maybe 1.24-1.26
    MCH Reference….…….0.76V............: [Auto]
    MCH/DRAM Ref.…......0.900V...........: [Auto]
    ICH I/O……………….....1.500V............: 1.590 V
    ICH Core…………….....1.100V.............: 1.200 V
    DRAM
    DRAM Voltage ……....1.800V............: 2.08V
    DRAM Termination .…0.900V............: [Auto]
    Channel A Reference 0.900V............: [Auto]
    Channel B Reference 0.900V............: [Auto]

    Advanced Settings
    Limit CPUID Max. to 3...................: [Disabled]
    No-Execute Memory Protect.........: [Enabled]
    CPU Enhanced Halt (C1E)..............: [Disabled]
    C2/C2E State Support..................: [Disabled]
    x C4/C4E State Support................: [Disabled]
    CPU Thermal Monitor 2(TM2) ........: [Enabled]
    CPU EIST Function.......................: [Disabled]
    Virtualization Technology...............: [Disabled]

Page 2 of 6 FirstFirst 1234 ... LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •