Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Results 1 to 6 of 6

Thread: ga-ep45-ud3p memory settings




  1. #1

    Default ga-ep45-ud3p memory settings

    1st time poster here. I have ga-ep45-ud3p w/e7200 2.53ghz (no overclock at this point) and kingston Khx85002k2/2gr.Of course it reads pc2-6400 at 800mhz. board is rev.1.0 f4 bios.Can some suggest the proper memory settings to get my memory to pc8500 1066mhz as advertised?
    Thanks

  2. #2
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: ga-ep45-ud3p memory settings

    Please link me to your exact ram, and tell me how many sticks you are using (2x1 or 2x2)

    Then fill this out with what you are using and I will advise back. Normally you just need to change your memory multi and set performance enhance to standard. But many other things may need set.

    This is Just a template I use to ask people their settings, pay no attention to the numbers in it, replace with yours

    Code:
    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: 
    CPU Clock Ratio ..........................: 9
    Fine CPU Clock Ratio.....................:.5
    CPU Frequency ...........................: 2.53
    
    
    Clock Chip Control 
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled] 
    CPU Host Frequency (Mhz) ............: 266Mhz
    PCI Express Frequency (Mhz) .........:Set to 100
    
    C.I.A.2 .................................:[Disabled]
    
    
    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 
    PCI Express Clock Drive.................: <<< 
    CPU Clock Skew (ps)....................: <<< 
    MCH Clock Skew (ps)...................: <<< 
    
    
    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: [Auto]
    System Memory Multiplier ..............: 4.00A
    Memory Frequency (Mhz) ..............: 1600
    DRAM Timing Selectable ................: [Manual]
    
    Standard Timing Control
    CAS Latency Time........................
    tRCD .........................................
    tRP'...........................................
    tRAS..........................................
    
    Advanced Timing Control
    tRRD...........................................
    tWTR..........................................
    tWR............................................
    tRFC...........................................
    tRTP...........................................
    Command Rate (CMD) ....................:2
    
    Driving Strength Profiles
    Driving Strength ............................
    
    Channel A
    Static tRead Value.........................:7-10
     tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
     tRD Phase2 Adjustment .................:Auto
     tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 
    Twr2wr(Different Rank)...................:Auto 
    Twr2rd(Different Rank)...................:Auto 
    Trd2wr(Same/Diff Rank)..................:Auto 
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
    
    Channel B
    Static tRead Value.........................:7-10
     tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
     tRD Phase2 Adjustment .................:Auto
     tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 
    Twr2wr(Different Rank)...................:Auto 
    Twr2rd(Different Rank)...................:Auto 
    Trd2wr(Same/Diff Rank)..................:Auto 
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
    
    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................:
    CPU Termination…..... 1.200V*.......: <<< Leave
    CPU PLL…………………....1.500V*.......: << Please set to stock, Auto overvolts this way to much
    
    CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly 
    
    CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly 
    
    MCH/ICH
    MCH Core…………….....1.100V...........: << 
    MCH Reference….…….0.800V...........; <<< Leave
    MCH/DRAM Ref.…......0.900V...........: <<< Leave
    ICH I/O……………….....1.550V............: <<< Leave
    ICH Core…………...……1.100V............: <<< Leave
    
    DRAM
    DRAM Voltage ……....1.800V............: 
    DRAM Termination .…0.900V............: <<< Leave
    Channel A Reference 0.900V............: <<< Leave
    Channel B Reference 0.900V............: <<< Leave
    
    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC
    
    Integrated Peripherals
    Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB

  3. #3

    Default Re: ga-ep45-ud3p memory settings

    I hope I did this right!www.valueram.com/datasheets/KHX8500D2K2_2G.pdf
    This kit is supposed to be a PC2-8500 dual channel kit. I have the sticks in slot1 and slot 3 if I understand the manual for dual channel config.

    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............:auto
    CPU Clock Ratio ..........................: 9
    Fine CPU Clock Ratio.....................:.+.5
    CPU Frequency ...........................: 2.53(266x9.5)


    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [disabled]
    CPU Host Frequency (Mhz) ............: 266Mhz
    PCI Express Frequency (Mhz) .........:Set to auto

    C.I.A.2 .................................:[Disabled]


    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 800mv
    PCI Express Clock Drive.................: <<< 900mv
    CPU Clock Skew (ps)....................: <<< ops
    MCH Clock Skew (ps)...................: <<<ops> ops


    DRAM Performance Control
    Performance Enhance...................: [auto]
    Extreme Memory Profile (X.M.P.).....: NA
    (G)MCH Frequency Latch...............: [Auto]
    System Memory Multiplier ..............: auto
    Memory Frequency (Mhz) ..............: 800
    DRAM Timing Selectable ................: [auto]

    Standard Timing Control
    CAS Latency Time........................5 auto
    tRCD .........................................5auto
    tRP'...........................................5 auto
    tRAS..........................................18 auto

    Advanced Timing Control
    tRRD...........................................3 auto
    tWTR..........................................3 auto
    tWR............................................6 auto
    tRFC...........................................42 auto
    tRTP...........................................3 auto
    Command Rate (CMD) ....................:0 auto

    Driving Strength Profiles
    Driving Strength ............................auto

    Channel A
    Static tRead Value.........................:5
    tRD Phase0 Adjustment...................:<<< Leave for all below as well 0
    tRD Phase1 Adjustment...................:0 auto
    tRD Phase2 Adjustment .................:0 auto
    tRD Phase3 Adjustment..................:0 auto
    Trd2rd(Different Rank)....................:6 auto
    Twr2wr(Different Rank)...................:6 auto
    Twr2rd(Different Rank)...................:5 auto
    Trd2wr(Same/Diff Rank)..................:8 auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Channel B
    Static tRead Value.........................:5
    tRD Phase0 Adjustment...................:<<< Leave for all below as well 0
    tRD Phase1 Adjustment...................:Auto 0
    tRD Phase2 Adjustment .................:Auto 0
    tRD Phase3 Adjustment..................:Auto 0
    Trd2rd(Different Rank)....................:Auto 6
    Twr2wr(Different Rank)...................:Auto 6
    Twr2rd(Different Rank)...................:Auto 5
    Trd2wr(Same/Diff Rank)..................:Auto 8
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Motherboard Voltage Control
    Voltage Type.………... normal
    Load line calibration disabled
    CPU
    CPU Vcore….……….........................:1.20000v auto
    CPU Termination…..... 1.200V*.......: <<< Leave 1.200v auto
    CPU PLL…………………....1.500V*.......: << Please set to stock, Auto overvolts this way to much 1.500v

    CPU Referen.…………....0.760V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly

    CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly NA

    MCH/ICH
    MCH Core…………….....1.100V...........: << 1.800v
    MCH Reference….…….0.800V...........; <<< Leave 0.760
    MCH/DRAM Ref.…......0.900V...........: <<< Leave 0.900v
    ICH I/O……………….....1.550V............: <<< Leave 1.500v
    ICH Core…………...……1.100V............: <<< Leave 1.100v

    DRAM
    DRAM Voltage ……....1.800V............: 1.800v
    DRAM Termination .…0.900V............: <<< Leave 0.900v
    Channel A Reference 0.900V............: <<< Leave 0.900v
    Channel B Reference 0.900V............: <<< Leave 0.900v

    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [enabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [enabled]
    Virtualization Technology................: [NA] Enabled if you use Vmware/Virtual PC

    Integrated Peripherals
    Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB</ops>

  4. #4
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: ga-ep45-ud3p memory settings

    Thanks!

    Yeap you linked it up right! Here would be optimal settings for the ones you provided and to get your ram at 1066 >>>>

    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............:auto or fast
    CPU Clock Ratio ..........................: 9
    Fine CPU Clock Ratio.....................:.+.5
    CPU Frequency ...........................: 2.53(266x9.5)


    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [disabled]
    CPU Host Frequency (Mhz) ............: 266Mhz
    PCI Express Frequency (Mhz) .........:100

    C.I.A.2 .................................:[Disabled]


    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 800mv
    PCI Express Clock Drive.................: <<< 900mv
    CPU Clock Skew (ps)....................: <<< ops
    MCH Clock Skew (ps)...................: << ops


    DRAM Performance Control
    Performance Enhance...................: [Standard]

    (G)MCH Frequency Latch...............: [Auto]
    System Memory Multiplier ..............: 4.00A
    Memory Frequency (Mhz) ..............: 1066
    DRAM Timing Selectable ................: [auto]

    Standard Timing Control
    CAS Latency Time........................5
    tRCD .........................................5
    tRP'...........................................5
    tRAS..........................................15/18

    Set below all to highest suggested, then later lower one at a time testing with memtest86+ as you go >>>
    Memtest86+ - Advanced Memory Diagnostic Tool


    Advanced Timing Control
    tRRD...........................................3-4
    tWTR..........................................3-6 (Set 12 first, then you can jump right to the lower range)

    tWR............................................4-6 (Set 14 first, then you can jump right to the lower range)

    tRFC...........................................38-42 (Set 48 first)
    tRTP...........................................3-6
    Command Rate (CMD) ....................:2

    Driving Strength Profiles
    Driving Strength ............................1066-1200 (1200 may be best)

    Channel A
    Static tRead Value.........................:6/7-10
    tRD Phase0 Adjustment...................:<<< Leave for all below as well 0
    tRD Phase1 Adjustment...................:0 auto
    tRD Phase2 Adjustment .................:0 auto
    tRD Phase3 Adjustment..................:0 auto
    Trd2rd(Different Rank)....................:6 auto
    Twr2wr(Different Rank)...................:6 auto
    Twr2rd(Different Rank)...................:5 auto
    Trd2wr(Same/Diff Rank)..................:8 auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Channel B
    Static tRead Value.........................:6/7-10
    tRD Phase0 Adjustment...................:<<< Leave for all below as well PLEASE Do set those above and below all to AUTO
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Motherboard Voltage Control
    Voltage Type.………... normal
    Load line calibration disabled
    CPU
    CPU Vcore….……….........................:1.20000v auto
    CPU Termination…..... 1.200V*.......: <<< Leave 1.200v Please set to stock, same as below applies to Auto

    CPU PLL…………………....1.500V*.......: << Please set to stock, Auto overvolts this way to much 1.500v

    CPU Referen.…………....0.760V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly

    CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly NA

    MCH/ICH
    MCH Core…………….....1.100V...........: << 1.800v << hope that is a misprint!!!! Set stock or Auto and you should be fine.

    MCH Reference….…….0.800V...........; <<< Auto
    MCH/DRAM Ref.…......0.900V...........: <<< Auto
    ICH I/O……………….....1.550V............: <<< Leave 1.500v
    ICH Core…………...……1.100V............: <<< Leave 1.100v

    DRAM
    DRAM Voltage ……....1.800V............: 2.1-2.2 (You ram is rated to 2.2, but may not need it, that is just warrantied voltages. Try 2.1 for sure first)

    DRAM Termination .…0.900V............: <<< Leave 0.900v
    Channel A Reference 0.900V............: <<< Leave 0.900v
    Channel B Reference 0.900V............: <<< Leave 0.900v

    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [enabled] << Disable to overclock
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [enabled] << Disable to overclock
    Virtualization Technology................: [NA] Enabled if you use Vmware/Virtual PC

    Integrated Peripherals
    Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB

  5. #5

    Default Re: ga-ep45-ud3p memory settings

    Ok, I'v never used memtest86. I have it downloaded to my desk top. It wants copied to a cd......then what how and where do I use it.

  6. #6
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: ga-ep45-ud3p memory settings

    Do you have a floppy? If so download the floppy version. The ISO needs to be burned as a image this is different then all other data burns. Here is a few ways to do that >>>
    How to Write ISO Files to CD

    Then you hit F12 at bootup and Choose Boot to CD and it will run

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •