Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 1 of 3 123 LastLast
Results 1 to 10 of 24

Thread: p35-ds4 with 8500c rams BSOD




  1. #1
    Join Date
    Nov 2008
    Posts
    12

    Unhappy p35-ds4 with 8500c rams BSOD

    hi all.. i need help i have a p35-ds4 mobo and 2x2gb corsair memories model 8500c and i cant make them run at their stock speed (1066) mhz i have them running at 1000mhz and i still get the problems sometimes can anyone tell me what can i do to fix my problem i dont want to underclock my computer anymore... thnx
    here are my computer specs

  2. #2
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: p35-ds4 with 8500c rams BSOD

    Please post me a link to your ram's exact model so I can check warrantied voltages, and then please fill this out with your settings as of now and I will advise back >>>>

    This is Just a template I use to ask people their settings, pay no attention to the numbers in it, replace with yours

    Code:
    Robust Graphics Booster___________ [Auto]
    CPU Clock Ratio ____________ [8] 
    Fine Clock Ratio ____________[0.5]
    CPU Host Clock Control_ [Enabled]
    CPU Host Frequency (MHz)__________ [450] 
    PCI Express Frequency (Mhz)_______ [100]
    C.I.A. 2__________________________ [Disabled]
    System Memory Multiplier (SPD)____ [2.00]
    DRAM Timing Selectable_______ SPD __ [Manual]
    
    Performance Enhance = [Standard]
    
    CAS Latency Time________________ ?
    Dram RAS# to CAS# Delay_________ ?
    Dram RAS# Precharge Delay_______?
    Precharge Delay (tRAS)__________ ?
    
    ACT to ACT Delay (tRRD)_________ ?
    Rank Write to READ Delay________ ?
    Write to Precharge Delay_________ ?
    Refresh to ACT Delay______________ ?
    Read to Precharge Delay__________ ?
    Static tRead Value_______________
    Static tRead Phase Adjust________ [Auto]
    
    CPU/PCIEX Clock Driving Control [800mV]
    CPU Clock Skew Control [normal]
    GMCH Clock Skew Control [Normal]
    
    System Voltage Control____ [Manual]
    DDR2 OverVoltage Control__ [+0.300V] 
    PCI-E OverVoltage Control_ [+0.1V] 
    FSB OverVoltage Control___ [+0.1V] 
    (G)MCH OverVoltage Control [+0.1V] 
    CPU Voltage Control_______ [1.25]
    
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC
    
    Integrated Peripherals
    Legacy USB Storage Detect___________________[Disabled] *Note* Must be enabled to flash from USB

  3. #3
    Join Date
    Nov 2008
    Posts
    12

    Default Re: p35-ds4 with 8500c rams BSOD

    Robust Graphics Booster___________ [Auto]
    CPU Clock Ratio ____________ [8]
    Fine Clock Ratio ____________xxx
    CPU Host Clock Control_ [Enabled]
    CPU Host Frequency (MHz)__________ [300]
    PCI Express Frequency (Mhz)_______ [auto]
    C.I.A. 2__________________________ [Disabled]
    System Memory Multiplier (SPD)____ [333]
    DRAM Timing Selectable_______ SPD __ [auto]

    Performance Enhance = [Standard]

    CAS Latency Time________________ 5
    Dram RAS# to CAS# Delay_________ 7
    Dram RAS# Precharge Delay_______7
    Precharge Delay (tRAS)__________ 24

    ACT to ACT Delay (tRRD)_________ 4
    Rank Write to READ Delay________ 4
    Write to Precharge Delay_________ 8
    Refresh to ACT Delay______________ 68
    Read to Precharge Delay__________ 4
    Static tRead Value_______________4
    Static tRead Phase Adjust________ 0


    System Voltage Control____ [Manual] auto
    DDR2 OverVoltage Control__ [+0.300V] normal
    PCI-E OverVoltage Control_ [+0.1V] normal
    FSB OverVoltage Control___ [+0.1V] normal
    (G)MCH OverVoltage Control [+0.1V] normal
    CPU Voltage Control_______ [1.25] 1.28750



    thats all i could found when i try to run it at 5-5-5-15 it doesnt even boot
    my ram model is cm2x2048-8500c5</pre>
    </pre>

  4. #4
    Join Date
    Apr 2008
    Posts
    942

    Default Re: p35-ds4 with 8500c rams BSOD

    I think you've mixed up memory multiplier with the system Bus.

    It may be that your board doesn't like the 3.00 multiplier at some settings (mine is like that).

    For starters underclock your ram, by setting:-

    1) Memory multiplier = 2.40
    2) Main memory settings = 5-5-5-15
    3) Advanced memory all to Auto; Except,
    4) tFRC (Refresh To Act Delay) = 56
    5) All voltages to Auto; Except,
    6) Set DDR2 Voltage to +0.2volts

    From that base, see how your system runs. This way we can rule out other problems. Your memory to full speed can be tweaked later.
    GA-P35C-DS3R Rev2.0 F11 bios, E8200 (@3.0Ghz), OCZ DDR3 PC3-10666 Reaper 4GB (@1200Mhz), Xonar D1, 8800GTS 512, Corsair HX520 (Single 12volt line, Max 40A), WDC 3200aaks/5000aaks in AHCI mode, Vista 64 Premium.

  5. #5
    Join Date
    Nov 2008
    Posts
    12

    Default Re: p35-ds4 with 8500c rams BSOD

    ok ready with that now i have my ram running at 640 mhz with a clock ratio at 9x and a cpu host frequency of 266 what do i do now to get my 1066? thnx

  6. #6
    Join Date
    Apr 2008
    Posts
    942

    Default Re: p35-ds4 with 8500c rams BSOD

    Quote Originally Posted by negrala View Post
    ok ready with that now i have my ram running at 640 mhz with a clock ratio at 9x and a cpu host frequency of 266 what do i do now to get my 1066? thnx
    From your settings I thought you had a 1333 FSB chip, so infact you have a 1066 chip?
    I didn't intend for you to start as low as 266 x 2.40 = 640Mhz. I thought your Host frequency was 333 as per the template above in your post.

    Ok i can see from the tiny print in the Screenshot now.

    Assuming you have no BSOD's now, try changing Just the memory multiplier to 3.00x, leaving the settings I gave you (above) exactly the same.
    GA-P35C-DS3R Rev2.0 F11 bios, E8200 (@3.0Ghz), OCZ DDR3 PC3-10666 Reaper 4GB (@1200Mhz), Xonar D1, 8800GTS 512, Corsair HX520 (Single 12volt line, Max 40A), WDC 3200aaks/5000aaks in AHCI mode, Vista 64 Premium.

  7. #7
    Join Date
    Nov 2008
    Posts
    12

    Default Re: p35-ds4 with 8500c rams BSOD

    ok i set the ratio to 8x and the cpu host to 300 and the memory multiplier to 333 no my ram is running at 1000 mhz thats what u wanted right now what do i do? xD

  8. #8
    Join Date
    Apr 2008
    Posts
    942

    Default Re: p35-ds4 with 8500c rams BSOD

    You've got a q6600 right? The CPU host frequency should be at 266Mhz for it to run at its normal speed.
    GA-P35C-DS3R Rev2.0 F11 bios, E8200 (@3.0Ghz), OCZ DDR3 PC3-10666 Reaper 4GB (@1200Mhz), Xonar D1, 8800GTS 512, Corsair HX520 (Single 12volt line, Max 40A), WDC 3200aaks/5000aaks in AHCI mode, Vista 64 Premium.

  9. #9
    Join Date
    Nov 2008
    Posts
    12

    Default Re: p35-ds4 with 8500c rams BSOD

    ok so i put it at 266 and the memory multipliear at 400?

  10. #10
    Join Date
    Apr 2008
    Posts
    942

    Default Re: p35-ds4 with 8500c rams BSOD

    Quote Originally Posted by negrala View Post
    ok so i put it at 266 and the memory multiplier at 400?
    Yes - That would be the correct combination for your CPU and your PC8500 (1066Mhz) ram.

    In MIT section of bios, you should change the following:-
    1) Set the main memory timings to 5-5-5-18
    2) Performance Enhance to Standard
    3) tRFC (Refresh To Act Delay) to 56
    GA-P35C-DS3R Rev2.0 F11 bios, E8200 (@3.0Ghz), OCZ DDR3 PC3-10666 Reaper 4GB (@1200Mhz), Xonar D1, 8800GTS 512, Corsair HX520 (Single 12volt line, Max 40A), WDC 3200aaks/5000aaks in AHCI mode, Vista 64 Premium.

Page 1 of 3 123 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •