Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 30

Thread: Instaling Ga-EP35-D3SL and e5200




  1. #11

    Default Re: Instaling Ga-EP35-D3SL and e5200

    I think i figured out the problem to my overclocking now. My memory multiplier was set to auto and I believe it was increasing my ram speed too much , therefore not booting.

    Changing some settings quickly this morning before I left for work, I was able to get my memory at 667 @ 3-3-3-10 +.3v

    The settings I used...


    Robust Graphics Booster___________ [Auto]
    CPU Clock Ratio ____________ [9]
    Fine Clock Ratio ____________[0.5]
    CPU Host Clock Control_ [Enabled]
    CPU Host Frequency (MHz)__________ [333]
    PCI Express Frequency (Mhz)_______ [100]
    C.I.A. 2__________________________ [Disabled]
    System Memory Multiplier (SPD)____ [2.00]
    DRAM Timing Selectable_______ SPD __ [Manual]

    Performance Enhance = [Standard]

    CAS Latency Time________________ 3
    Dram RAS# to CAS# Delay_________ 3
    Dram RAS# Precharge Delay_______ 3
    Precharge Delay (tRAS)__________ 10

    ACT to ACT Delay (tRRD)_________[Auto]
    Rank Write to READ Delay________[Auto]
    Write to Precharge Delay________[Auto]
    Refresh to ACT Delay____________[Auto]
    Read to Precharge Delay_________[Auto]
    Static tRead Value______________[Auto]
    Static tRead Phase Adjust_______[Auto]

    System Voltage Control____ [Manual]
    DDR2 OverVoltage Control__ [+0.300V]
    PCI-E OverVoltage Control_ [Normal]
    FSB OverVoltage Control___ [+0.1V]
    (G)MCH OverVoltage Control [+0.1V]
    CPU Voltage Control_______ [1.3X](I can't remember the exact voltage,lol)

    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Disabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled]

    Integrated Peripherals
    Legacy USB Storage Detect___________________[Disabled] *Note* Must be enabled to flash from USB</pre>



    Just before running out the door, I was able to set memtest to run. Hopefully when I reach home it will be error free.

    :)
    Nothing is impossible... Just mathematically improbable..

    "The best defense against computer viruses might not even be antivirus software, but a crafty combination of education and common sense."

    Intel Pentium e5200 @ 3.8HZ (380 X 10)
    Giga-byte GA-EP35-DS3L
    Mushkin 4GB DDR2 800 @ 760MHZ 4-4-3-10 @ +0.3v
    SAPPHIRE 100245L Radeon HD 4850 512MB 256-bit GDDR3 PCI Express 2.0 x16
    Seagate 160GB @ 7200rpm
    SB Audigy2
    Corsair 520HX
    Super Antec Lanboy
    Windows 7 Ultimate 64bit RTM
    Acer AL2216Wbd 22"

  2. #12
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Instaling Ga-EP35-D3SL and e5200

    Ahh ya, I wondered why you have you ram at 667. No you wont be able to run 3.8-4Ghz with 667 ram speed at all

    The lowest you would be able to run your ram at 3.8 would be 800Mhz, and therefore you would have to move up to 444-12 timings

  3. #13

    Default Re: Instaling Ga-EP35-D3SL and e5200

    So I'm guessing overclocking it to 800mhz @ 4-4-4-12 with 400x10 (4.0ghz) will be reachable? Also. Will the +.3v suffice or will I have to pump more RAM voltage?

    And at 400mhz I'm guessing the FSB and Northbridge voltages will have to go up as well? +.2? +.3?

    Can you help me with the advanced ram timing settings? First experience with such settings.

    Finally, different programs give me different Core temps. I tried Realtemp, speed fan and easy tune 6. I now saw one of your other posts stating that for P35 I'll need easy tune 5. Will download later at home.
    Nothing is impossible... Just mathematically improbable..

    "The best defense against computer viruses might not even be antivirus software, but a crafty combination of education and common sense."

    Intel Pentium e5200 @ 3.8HZ (380 X 10)
    Giga-byte GA-EP35-DS3L
    Mushkin 4GB DDR2 800 @ 760MHZ 4-4-3-10 @ +0.3v
    SAPPHIRE 100245L Radeon HD 4850 512MB 256-bit GDDR3 PCI Express 2.0 x16
    Seagate 160GB @ 7200rpm
    SB Audigy2
    Corsair 520HX
    Super Antec Lanboy
    Windows 7 Ultimate 64bit RTM
    Acer AL2216Wbd 22"

  4. #14
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Instaling Ga-EP35-D3SL and e5200

    Yes, you can most often run 667 ram at 800 just with looser timings, same applies to 800 ram ran at 1066. You may not even need +.3V you may be able to use +.2, but I doubt you would need more then +.3 in any case

    That CPU may not do 4Ghz at all though, so dont count on it

    FSB and NB voltages would likely be fine at 400 FSB, use 402 though so you are not right on the strap line. Vcore will for sure likely need to be added though. And yes you could add +0.1 to MCH and FSB for stability if you like, then lower later after you are stable and see if it is still ok

    Here would be optimal settings for 800Mhz ram 2x1GB >>>

    Performance Enhance = [Standard]

    CAS Latency Time________________ 4
    Dram RAS# to CAS# Delay_________ 4
    Dram RAS# Precharge Delay_______4
    Precharge Delay (tRAS)__________ 12/15

    ACT to ACT Delay (tRRD)_________ 3-4
    Rank Write to READ Delay________ 3-6 (Also bench 9-11 later)
    Write to Precharge Delay_________ 4-6
    Refresh to ACT Delay______________ 38-42
    Read to Precharge Delay__________ 3-6
    Static tRead Value_______________ 7-10
    Static tRead Phase Adjust________ [Auto] <<< Always Auto

    For Core Temps, I suggest CoreTemp >>>
    Core Temp

    RealTemp is great as well, but MUST be calibrated >>>
    RealTemp Installation & Calibration Page

    Latest Beta can be found here for RealTemp >>
    http://forums.tweaktown.com/f69/inte...94/#post262787

    EasyTune will only show you CPU Temps, which you do not need to worry about, only Core temps

  5. #15

    Default Re: Instaling Ga-EP35-D3SL and e5200

    Aww @ no 4GHZ.. I've seen people do it on air already. Lets be optimistic! :)

    Anyway when I got home no errors on memtest so I went for 800mhz @ 4-4-4-12 @ +.2

    Settings I u sed

    Robust Graphics Booster___________ [Fast
    CPU Clock Ratio ____________ [7]
    Fine Clock Ratio ____________[0.5]
    CPU Host Clock Control_ [Enabled]
    CPU Host Frequency (MHz)__________ [333]
    PCI Express Frequency (Mhz)_______ [100]
    C.I.A. 2__________________________ [Disabled]
    System Memory Multiplier (SPD)____ [2.40]
    Memory Frequency_______________[800]
    DRAM Timing Selectable_______ SPD __ [Manual]

    Performance Enhance = [Standard]

    CAS Latency Time________________ 4
    Dram RAS# to CAS# Delay_________ 4
    Dram RAS# Precharge Delay_______ 4
    Precharge Delay (tRAS)__________ 12

    ACT to ACT Delay (tRRD)_________4
    Rank Write to READ Delay________6
    Write to Precharge Delay________6
    Refresh to ACT Delay____________42
    Read to Precharge Delay_________6
    Static tRead Value______________10
    Static tRead Phase Adjust_______Auto

    System Voltage Control____ [Manual]
    DDR2 OverVoltage Control__ [+0.2v]
    PCI-E OverVoltage Control_ [Normal]
    FSB OverVoltage Control___ [+0.1V]
    (G)MCH OverVoltage Control [+0.1V]
    CPU Voltage Control_______ [1.325]

    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Disabled]
    CPU EIST Function.........................: [Disabled


    So.. Computer booted fine. No problems.. Im almost 100% sure these settings will produce no errors..



    Where do i go from here? Start inching up that 333 FSB? Or the multiplier? What about my advanced RAM timings. Are they good? Can they be better?

    Thanks in advance.
    Nothing is impossible... Just mathematically improbable..

    "The best defense against computer viruses might not even be antivirus software, but a crafty combination of education and common sense."

    Intel Pentium e5200 @ 3.8HZ (380 X 10)
    Giga-byte GA-EP35-DS3L
    Mushkin 4GB DDR2 800 @ 760MHZ 4-4-3-10 @ +0.3v
    SAPPHIRE 100245L Radeon HD 4850 512MB 256-bit GDDR3 PCI Express 2.0 x16
    Seagate 160GB @ 7200rpm
    SB Audigy2
    Corsair 520HX
    Super Antec Lanboy
    Windows 7 Ultimate 64bit RTM
    Acer AL2216Wbd 22"

  6. #16
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Instaling Ga-EP35-D3SL and e5200

    Ahh, OK then you may be able to get 4Ghz... Sorry bud!

    Well you will want to leave your advanced timings loose like you have them until you get your CPU where you want it. Then you can lower them

    I would shoot for 10x402 for 4GHz with that CPU so you can have 1:1 with your ram and it may be the easiest way to do it

    So I would switch to 10x333 and then start upping the FSB until it fails, then add more Vcore until it does not, and so on and so forth until you get 402 FSB

    Keep this enabled >>>
    CPU Thermal Monitor 2(TM2) ...........: [Disabled]

    Good luck, I am on my way out the door so I will see you tonight most likely!

  7. #17

    Default Re: Instaling Ga-EP35-D3SL and e5200

    Ok.. Im up to 3.9Ghz.. 400x10 just would not boot. I tried increasing the voltage but still nothing.

    I'm pretty happy at 3.9GHZ now.

    Realtemp gives me temperatures of around 30-32 on both cores.

    My ram is @ 390MHZ 4-4-4-12.

    I still have not tested this yet but I hope it's stable. I'll use it for a little while and let it test overnight..
    Nothing is impossible... Just mathematically improbable..

    "The best defense against computer viruses might not even be antivirus software, but a crafty combination of education and common sense."

    Intel Pentium e5200 @ 3.8HZ (380 X 10)
    Giga-byte GA-EP35-DS3L
    Mushkin 4GB DDR2 800 @ 760MHZ 4-4-3-10 @ +0.3v
    SAPPHIRE 100245L Radeon HD 4850 512MB 256-bit GDDR3 PCI Express 2.0 x16
    Seagate 160GB @ 7200rpm
    SB Audigy2
    Corsair 520HX
    Super Antec Lanboy
    Windows 7 Ultimate 64bit RTM
    Acer AL2216Wbd 22"

  8. #18

    Default Re: Instaling Ga-EP35-D3SL and e5200

    So.. I decided to run a small test using Prime 95 v 25.8... When I use this version I get an error within a couple of seconds.. but if i use version 24.1 I don't get any error..

    I've googled this error and i've seen people getting it at stock BIOS settings.. I'm a bit confused now..

    Nothing is impossible... Just mathematically improbable..

    "The best defense against computer viruses might not even be antivirus software, but a crafty combination of education and common sense."

    Intel Pentium e5200 @ 3.8HZ (380 X 10)
    Giga-byte GA-EP35-DS3L
    Mushkin 4GB DDR2 800 @ 760MHZ 4-4-3-10 @ +0.3v
    SAPPHIRE 100245L Radeon HD 4850 512MB 256-bit GDDR3 PCI Express 2.0 x16
    Seagate 160GB @ 7200rpm
    SB Audigy2
    Corsair 520HX
    Super Antec Lanboy
    Windows 7 Ultimate 64bit RTM
    Acer AL2216Wbd 22"

  9. #19

    Default Re: Instaling Ga-EP35-D3SL and e5200

    Ok. I believe it was something to do with the voltage drop... My voltage is not set to 1.5v in the bios and the test is running fine. I will leave it over night and if all goes well then ill drop it to 1.4.. Going to feel around for the right voltage.

    This may take some time -_-"
    Nothing is impossible... Just mathematically improbable..

    "The best defense against computer viruses might not even be antivirus software, but a crafty combination of education and common sense."

    Intel Pentium e5200 @ 3.8HZ (380 X 10)
    Giga-byte GA-EP35-DS3L
    Mushkin 4GB DDR2 800 @ 760MHZ 4-4-3-10 @ +0.3v
    SAPPHIRE 100245L Radeon HD 4850 512MB 256-bit GDDR3 PCI Express 2.0 x16
    Seagate 160GB @ 7200rpm
    SB Audigy2
    Corsair 520HX
    Super Antec Lanboy
    Windows 7 Ultimate 64bit RTM
    Acer AL2216Wbd 22"

  10. #20
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Instaling Ga-EP35-D3SL and e5200

    Try Orthos. Ya finding correct voltages is a bit tricky and will take some time usually

    Ya did good! I thought I would come back today to see you clocked up there! Once you get 3.9 stable save that as a Profile using F11 on the MAIN Page of the BIOS (F12 is load) then you can try for 4Ghz and load the 3.9 profile anytime you need to

Page 2 of 3 FirstFirst 123 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •