Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 3 of 3 FirstFirst 123
Results 21 to 30 of 30

Thread: Instaling Ga-EP35-D3SL and e5200




  1. #21

    Default Re: Instaling Ga-EP35-D3SL and e5200

    I used Intel burn test thingy to test the 3.9 @ 1.5, it was stable. Did not get around to testing the 1.4 yet.

    A friend was telling me that it's better to keep your multiplier at the lowest and just crank up the FSB. Higher FSB is better theoretically he said.

    What's up with that?

    And yes. I am going to go for 4GHZ again.

    One more thing.. Some programs ( like orthos) detect my CPU speed at 4.87GHZ.. ? :S
    Nothing is impossible... Just mathematically improbable..

    "The best defense against computer viruses might not even be antivirus software, but a crafty combination of education and common sense."

    Intel Pentium e5200 @ 3.8HZ (380 X 10)
    Giga-byte GA-EP35-DS3L
    Mushkin 4GB DDR2 800 @ 760MHZ 4-4-3-10 @ +0.3v
    SAPPHIRE 100245L Radeon HD 4850 512MB 256-bit GDDR3 PCI Express 2.0 x16
    Seagate 160GB @ 7200rpm
    SB Audigy2
    Corsair 520HX
    Super Antec Lanboy
    Windows 7 Ultimate 64bit RTM
    Acer AL2216Wbd 22"

  2. #22
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Instaling Ga-EP35-D3SL and e5200

    1.5V is alot! And likely very hot! Is that actual voltage shown by CPU-z?

    You should for sure not need that much

    What orthos are you using, version I mean? Mine always shows same as CPU-z, maybe just your CPU confuses it? I'm using 20060420

    Yes, more FSB is best for sure, everything else follows. So for sure dont use 12.5 Multi or something like that. But do keep in mind your at 2.00 Memory multi you cant go much past 400-450 FSB with that ram Maybe 500 FSB would be possible with 555-18 timings, but it would be pushing that ram to it's max (If even possible, and may kill it pretty quick)

  3. #23

    Default Re: Instaling Ga-EP35-D3SL and e5200

    I just need to get the voltages worked out..

    But i think Im content with settings as is.

    Looking to get some new ram as well. 1000 or 1066?

    Probably just wondering if I can get my ram timings any tighter.. Will post full settings later..

    My northbridge and fsb volts at +.3.. i think thats too high.. i think something wrong :(
    Nothing is impossible... Just mathematically improbable..

    "The best defense against computer viruses might not even be antivirus software, but a crafty combination of education and common sense."

    Intel Pentium e5200 @ 3.8HZ (380 X 10)
    Giga-byte GA-EP35-DS3L
    Mushkin 4GB DDR2 800 @ 760MHZ 4-4-3-10 @ +0.3v
    SAPPHIRE 100245L Radeon HD 4850 512MB 256-bit GDDR3 PCI Express 2.0 x16
    Seagate 160GB @ 7200rpm
    SB Audigy2
    Corsair 520HX
    Super Antec Lanboy
    Windows 7 Ultimate 64bit RTM
    Acer AL2216Wbd 22"

  4. #24
    Join Date
    Jul 2008
    Location
    BigTen
    Posts
    60

    Default Re: Instaling Ga-EP35-D3SL and e5200

    Soldier,

    Here's a link to my 65nm E2160 Spec Finder page ... VID Voltage Range: 0.85v - 1.5v
    If I set my 65nm processor to 1.475v in BIOS, it reads between 1.492-1.508 in PC Health.
    I intend to not exceed the designed VID Voltage Range, so I will never set it higher than 1.475v.


    Here's a link to your 45nm E5200 Spec Finder page ... VID Voltage Range: 0.85v - 1.3625v
    This bears repeating ...
    Quote Originally Posted by Lsdmeasap View Post
    1.5V is alot!
    Gigabyte P35-S3G . 50mm Fan on MCH +0.2v
    Intel E6500 (9 x 420) 3780mHz 1.33125v
    G.Skill 4x1GB
    PC2-6400-NQ
    840mHz +0.2v
    Gigabyte HD4850 . Acer X223W . Acer X193W+
    Rosewill
    RP500-2 . WD WD3200AAJS . Masscool 8WA741

  5. #25

    Default Re: Instaling Ga-EP35-D3SL and e5200

    Been out of it for the weekend. I'm so confused as to whats going on right now. Will post settings when I get home from work.

    My voltage is at 1.425 now. If I remember properly, it won't boot at 1.4 even with my northbridge and fsb voltage set at +0.3.

    My temps are great but a friend told me for those voltages those temps cannot be real.

    Can someone shine some advice on me here please? Thanks.
    Nothing is impossible... Just mathematically improbable..

    "The best defense against computer viruses might not even be antivirus software, but a crafty combination of education and common sense."

    Intel Pentium e5200 @ 3.8HZ (380 X 10)
    Giga-byte GA-EP35-DS3L
    Mushkin 4GB DDR2 800 @ 760MHZ 4-4-3-10 @ +0.3v
    SAPPHIRE 100245L Radeon HD 4850 512MB 256-bit GDDR3 PCI Express 2.0 x16
    Seagate 160GB @ 7200rpm
    SB Audigy2
    Corsair 520HX
    Super Antec Lanboy
    Windows 7 Ultimate 64bit RTM
    Acer AL2216Wbd 22"

  6. #26
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Instaling Ga-EP35-D3SL and e5200

    Hmm, maybe too much FSB for sure and possibly too much MCH as well causing you to think you need 1.4+ vcore?

    I'd have to see all your settings to be sure though

    What temps are you telling your friend (Like CPU or Core Temps, or system temps)? And what are those temps and what program are you using to check them?

  7. #27

    Default Re: Instaling Ga-EP35-D3SL and e5200

    Settings:

    Robust Graphics Booster___________ [Fast
    CPU Clock Ratio ____________ [10]
    Fine Clock Ratio ____________[0.0]
    CPU Host Clock Control_ [Enabled]
    CPU Host Frequency (MHz)__________ 3.90GHZ[390]
    PCI Express Frequency (Mhz)_______ [100]
    C.I.A. 2__________________________ [Disabled]
    System Memory Multiplier (SPD)____ [2.00]
    Memory Frequency_______________[780]
    DRAM Timing Selectable_______ SPD __ [Manual]

    Performance Enhance = [Standard]

    CAS Latency Time________________ 4
    Dram RAS# to CAS# Delay_________ 4
    Dram RAS# Precharge Delay_______ 4
    Precharge Delay (tRAS)__________ 12

    ACT to ACT Delay (tRRD)_________4
    Rank Write to READ Delay________6
    Write to Precharge Delay________6
    Refresh to ACT Delay____________42
    Read to Precharge Delay_________6
    Static tRead Value______________10
    Static tRead Phase Adjust_______Auto

    System Voltage Control____ [Manual]
    DDR2 OverVoltage Control__ [+0.3v]
    PCI-E OverVoltage Control_ [Normal]
    FSB OverVoltage Control___ [+0.2V]
    (G)MCH OverVoltage Control [+0.2V]
    CPU Voltage Control_______ [1.4500]

    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Disabled]
    CPU EIST Function.........................: [Disabled

    My temps idle at around 30 - 32. I use realtemp to monitor my temps.

    With 1.4000v, I will fail IBT. I think however, it's because of the Vdrop. It's big.

    CPUZ reads Vcore at 1.408...
    Nothing is impossible... Just mathematically improbable..

    "The best defense against computer viruses might not even be antivirus software, but a crafty combination of education and common sense."

    Intel Pentium e5200 @ 3.8HZ (380 X 10)
    Giga-byte GA-EP35-DS3L
    Mushkin 4GB DDR2 800 @ 760MHZ 4-4-3-10 @ +0.3v
    SAPPHIRE 100245L Radeon HD 4850 512MB 256-bit GDDR3 PCI Express 2.0 x16
    Seagate 160GB @ 7200rpm
    SB Audigy2
    Corsair 520HX
    Super Antec Lanboy
    Windows 7 Ultimate 64bit RTM
    Acer AL2216Wbd 22"

  8. #28
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Instaling Ga-EP35-D3SL and e5200

    This should be enabled >>
    CPU Thermal Monitor 2(TM2) ...........: [Disabled]

    What is your voltage at load with orthos or prime running? Just trying to see what vdroop you have

    Is this just one 2GB stick? I think I asked before, but just wanted to be sure.

    If so you can likely use these voltages >>>
    System Voltage Control____ [Manual]
    DDR2 OverVoltage Control__ [+0.3v]
    PCI-E OverVoltage Control_ [Normal]
    FSB OverVoltage Control___ [+0.2V] << Only +0.1
    (G)MCH OverVoltage Control [+0.2V] << Only +0.1
    CPU Voltage Control_______ [1.4500]

  9. #29

    Default Re: Instaling Ga-EP35-D3SL and e5200

    I'm not sure at voltage load, will need to check that out. I have 2X1.

    Another question. Why enable TM2? I'm reading online that TM2 is a power saving option and must be disabled for overclock.

    Please explain.
    Nothing is impossible... Just mathematically improbable..

    "The best defense against computer viruses might not even be antivirus software, but a crafty combination of education and common sense."

    Intel Pentium e5200 @ 3.8HZ (380 X 10)
    Giga-byte GA-EP35-DS3L
    Mushkin 4GB DDR2 800 @ 760MHZ 4-4-3-10 @ +0.3v
    SAPPHIRE 100245L Radeon HD 4850 512MB 256-bit GDDR3 PCI Express 2.0 x16
    Seagate 160GB @ 7200rpm
    SB Audigy2
    Corsair 520HX
    Super Antec Lanboy
    Windows 7 Ultimate 64bit RTM
    Acer AL2216Wbd 22"

  10. #30
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Instaling Ga-EP35-D3SL and e5200

    TM2 is not a power saving option, those are C1E and EIST. It is part of Speedstep, but only as a failsafe incase of issues

    TM2 is a "Shut Down/Warn" Failsafe you incase your CPU Reaches TjMax or triggered by excessively high temperatures. When and if reached your CPU will scale down clocks and Voltage to save it from dying

    Self throttle – The digital temperature detector trips when junction temperature reaches maximum junction temperature and initiates TM1 or TM2 power control cycle. Platforms that use software control mechanisms, use self thermal monitor as a fail-safe mechanism only, since it is much faster then the software, and can guarantee fast respond time.
    http://www.cs.virginia.edu/~skadron/tacs/men.pdf

    If temperatures increase beyond Hot Scale, then ~ 5c below Tjunction Max, Throttling is activated. The Digital Thermal Sensors (DTS) are used to trigger Intel`s TM1 and TM2 technologies for frequency, multiplier and Vcore Throttling within individual Cores. If Core temperatures increase further to Tjunction Max, then Shutdown occurs. Since Tcase indicates CPU Die temperature only, it is not used for Throttle or Shutdown activation, however, as Tcase Max will be exceeded before Tjunction Max is reached, Tcase Max is always the limiting thermal specification.
    More of the same >>>

    Thermal Monitor 2 (TM2)

    When the thermal treshold is exceeded, TM2 changes the clock speed and core voltage to reduce the CPU power consumption. All cores will activate TM2 simultaneously as there is no per-core support. Users will not feel the choppiness as the transition between P-states are very smooth. TM2 is only supported by the CPU.
    Tech ARP - PC Power Management Guide Rev. 2.0

    More tests and info
    Performance and Power Consumption Control Features in Intel Pentium 4 and Intel Xeon Processors &ndash; Different Names, the Same Principles

    In the end, it should be enabled incase your CPU Fan stops or something else goes wrong and you are not around! It will not affect your Overclock at all

Page 3 of 3 FirstFirst 123

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •