Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 2 of 4 FirstFirst 1234 LastLast
Results 11 to 20 of 37

Thread: GA-EP45-UD3R and OCZ OCZ2RPR10664GK (2X2G) DDR2 1066




  1. #11
    Join Date
    Dec 2008
    Posts
    12

    Default Re: GA-EP45-UD3R and OCZ OCZ2RPR10664GK (2X2G) DDR2 1066

    OK, I loaded optimized settings, saved, reboot. Then loaded settings you posted (tried various setting if there was a range). Still will not post with both sticks.

    The only thing I haven't tried is new BIOS, there is an F4 and I'm on F3. Think this is the issue?

    I ran 8 passes of Memtest86+ on 1 stick, 0 errors. Ran 28 passes on other stick 0 errors.

  2. #12
    Join Date
    Dec 2008
    Posts
    12

    Default Re: GA-EP45-UD3R and OCZ OCZ2RPR10664GK (2X2G) DDR2 1066

    Bump, any more thoughts?

  3. #13
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: GA-EP45-UD3R and OCZ OCZ2RPR10664GK (2X2G) DDR2 1066

    Please post me your exact settings you are trying that fail and I can better advise you.

    And yes, a BIOS update could fix things possibly. Do read this >>>
    http://forums.tweaktown.com/f69/bios...h-guide-27576/

  4. #14
    Join Date
    Dec 2008
    Posts
    12

    Default Re: GA-EP45-UD3R and OCZ OCZ2RPR10664GK (2X2G) DDR2 1066

    Ok, updated to latest BIOS F5, loaded optimized settings/reboot re-entered BIOS and entered the following:

    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Auto
    CPU Clock Ratio ..........................: 9X
    Fine CPU Clock Ratio.....................:.+0.5
    CPU Frequency ...........................: 3.16 (333*9.5)


    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Disabled]
    CPU Host Frequency (Mhz) ............: 333Mhz
    PCI Express Frequency (Mhz) .........:100

    C.I.A.2 .................................:[Disabled]


    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 800
    PCI Express Clock Drive.................: <<< 900
    CPU Clock Skew (ps)....................: <<< 0
    MCH Clock Skew (ps)...................: <<< 50


    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: [Auto]
    System Memory Multiplier ..............: 3.20B
    Memory Frequency (Mhz) ..............: 1066
    DRAM Timing Selectable ................: Manual

    Standard Timing Control
    CAS Latency Time........................5
    tRCD .........................................5
    tRP'...........................................5
    tRAS..........................................15

    Advanced Timing Control
    tRRD...........................................3
    tWTR..........................................3
    tWR............................................4
    tRFC...........................................52
    tRTP...........................................3
    Command Rate (CMD) ....................:2

    Driving Strength Profiles
    Driving Strength ............................1066

    Channel A
    Static tRead Value.........................:8
    tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Channel B
    Static tRead Value.........................:8
    tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................:1.175 AUto
    CPU Termination…..... 1.200V*.......: <<< See below comment (Set to stock for now)
    CPU PLL…………………....1.500V*.......: << 1.25

    CPU Referen.…………....0.76V*.......: <<< .Auto


    MCH/ICH
    MCH Core…………….....1.100V...........: << 1.24
    MCH Reference….…….0.760V...........; <<< Leave
    MCH/DRAM Ref.…......0.900V...........: <<< Leave
    ICH I/O……………….....1.500V............: <<<1.57
    ICH Core…………...……1.100V............: <<< 1.2

    DRAM
    DRAM Voltage ……....1.800V............: 2.0
    DRAM Termination .…0.900V............: <<< Leave
    Channel A Reference 0.900V............: <<< Leave
    Channel B Reference 0.900V............: <<< Leave

    I also put both sticks in, one in yellow channel, one in red channel to avoid dual channel and it posts. I'm currently running another memtest86+ while I'm at work to see if I get any errors (I've already run 36 passes between the two sticks, no errors). I'm now trying with both stick in, not dual channel.<!-- / message --><!-- sig -->

  5. #15
    Join Date
    Dec 2008
    Posts
    12

    Default Re: GA-EP45-UD3R and OCZ OCZ2RPR10664GK (2X2G) DDR2 1066

    bump for help

  6. #16
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: GA-EP45-UD3R and OCZ OCZ2RPR10664GK (2X2G) DDR2 1066

    Sorry, got a bit Behind here!


    Put both sticks in dual channel please. Use slots 1+3 or 2+4, try this and once you get going you can start lowering things.

    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Auto
    CPU Clock Ratio ..........................: 9X
    Fine CPU Clock Ratio.....................:.+0.5
    CPU Frequency ...........................: 3.16 (333*9.5)


    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Disabled]
    CPU Host Frequency (Mhz) ............: 333Mhz
    PCI Express Frequency (Mhz) .........:100

    C.I.A.2 .................................:[Disabled]


    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 800
    PCI Express Clock Drive.................: <<< 900
    CPU Clock Skew (ps)....................: <<< 0 << try 50
    MCH Clock Skew (ps)...................: <<< 50 << try 150


    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: [Auto]
    System Memory Multiplier ..............: 3.20B
    Memory Frequency (Mhz) ..............: 1066
    DRAM Timing Selectable ................: Manual

    Standard Timing Control
    CAS Latency Time........................5
    tRCD .........................................5
    tRP'...........................................5
    tRAS..........................................18

    Advanced Timing Control
    tRRD...........................................3-4 << Set to 5 for now
    tWTR..........................................3-6 << Set to 12 for now
    tWR............................................4-6 << Set to 14 for now
    tRFC...........................................52-62 << Set to 68 for now
    tRTP...........................................3-5 << Set to 5 for now
    Command Rate (CMD) ....................:2

    Driving Strength Profiles
    Driving Strength ............................800/1066

    Channel A
    Static tRead Value.........................:8 << Set 9 for now
    tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Channel B
    Static tRead Value.........................:8 << Set 9 for now
    tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................:1.175 AUto
    CPU Termination…..... 1.200V*.......: <<< See below comment (Set to stock for now)
    CPU PLL…………………....1.500V*.......: << 1.25 << Why so low? Stock is 1.5

    CPU Referen.…………....0.76V*.......: <<< .Auto


    MCH/ICH
    MCH Core…………….....1.100V...........: << 1.24 << May need 1.26-1.28 for now
    MCH Reference….…….0.760V...........; <<< Leave
    MCH/DRAM Ref.…......0.900V...........: <<< Leave
    ICH I/O……………….....1.500V............: <<<1.57
    ICH Core…………...……1.100V............: <<< 1.2

    DRAM
    DRAM Voltage ……....1.800V............: 2.1-2.2
    DRAM Termination .…0.900V............: <<< Leave
    Channel A Reference 0.900V............: <<< Leave
    Channel B Reference 0.900V............: <<< Leave

  7. #17
    Join Date
    Dec 2008
    Posts
    12

    Default Re: GA-EP45-UD3R and OCZ OCZ2RPR10664GK (2X2G) DDR2 1066

    I tried the settings you posted above, no luck...

  8. #18
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: GA-EP45-UD3R and OCZ OCZ2RPR10664GK (2X2G) DDR2 1066

    Thats no good! Sounds like you didnt try very long.

    Please post the exact settings you tried and I will suggest back

    And hey, how did it "Not work"? BSOD, error in something, almost boot?

  9. #19
    Join Date
    Dec 2008
    Posts
    12

    Default Re: GA-EP45-UD3R and OCZ OCZ2RPR10664GK (2X2G) DDR2 1066

    Sorry for the short response, I'll elaborate -

    I put both sticks in dual channel 1+3 after setting the BIOS to the below with 1 stick in so I could enter BIOS. When I booted the computer it would not POST, it turns on for 6-30 seconds before shutting down and turning back on only to shut off again in 6-30 seconds. Seems to cycle on and off without ever posting or getting motherboard screen, nothing ever shows up on monitor. Should I let this cyclying occur for a while? Would that help?

    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Auto
    CPU Clock Ratio ..........................: 9X
    Fine CPU Clock Ratio.....................:.+0.5
    CPU Frequency ...........................: 3.16 (333*9.5)


    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Disabled]
    CPU Host Frequency (Mhz) ............: 333Mhz
    PCI Express Frequency (Mhz) .........:100

    C.I.A.2 .................................:[Disabled]


    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 800
    PCI Express Clock Drive.................: <<< 900
    CPU Clock Skew (ps)....................: <<< 50
    MCH Clock Skew (ps)...................: <<< 150


    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: [Auto]
    System Memory Multiplier ..............: 3.20B
    Memory Frequency (Mhz) ..............: 1066
    DRAM Timing Selectable ................: Manual

    Standard Timing Control
    CAS Latency Time........................5
    tRCD .........................................5
    tRP'...........................................5
    tRAS..........................................18

    Advanced Timing Control
    tRRD...........................................5
    tWTR..........................................12
    tWR............................................14
    tRFC...........................................68
    tRTP...........................................5
    Command Rate (CMD) ....................:2

    Driving Strength Profiles
    Driving Strength ............................800

    Channel A
    Static tRead Value.........................:9
    tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Channel B
    Static tRead Value.........................:9
    tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................:1.175 AUto
    CPU Termination…..... 1.200V*.......: <<< See below comment (Set to stock for now)
    CPU PLL…………………....1.500V*.......: << 1.50 << Why so low? Stock is 1.5

    CPU Referen.…………....0.76V*.......: <<< .Auto


    MCH/ICH
    MCH Core…………….....1.100V...........: << 1.28
    MCH Reference….…….0.760V...........; <<< Leave
    MCH/DRAM Ref.…......0.900V...........: <<< Leave
    ICH I/O……………….....1.500V............: <<<1.57
    ICH Core…………...……1.100V............: <<< 1.2

    DRAM
    DRAM Voltage ……....1.800V............: 2.2
    DRAM Termination .…0.900V............: <<< Leave
    Channel A Reference 0.900V............: <<< Leave
    Channel B Reference 0.900V............: <<< Leave

    One question about your comments -
    "CPU Termination…..... 1.200V*.......: <<< See below comment (Set to stock for now)
    CPU PLL…………………....1.500V*.......: << 1.50 << Why so low? Stock is 1.5"
    Does this mean both of these should be set to 1.50? I have CPU Termination at 1.20V and CPU PLL at 1.5?

    <!-- / message --><!-- sig -->

  10. #20
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: GA-EP45-UD3R and OCZ OCZ2RPR10664GK (2X2G) DDR2 1066

    Na dont need to let that go, I just wondered what you meant by not working as there could be many ways that could play out. Sounds like a setting is still off. I forget, you have tested each stick one by one correct? Just checking

    See if this helps any, also try using slots 2+4 to see if maybe 1 or 3 is faulty

    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: fast
    CPU Clock Ratio ..........................: 9X
    Fine CPU Clock Ratio.....................:.+0.5
    CPU Frequency ...........................: 3.16 (333*9.5)


    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Disabled]
    CPU Host Frequency (Mhz) ............: 333Mhz
    PCI Express Frequency (Mhz) .........:100

    C.I.A.2 .................................:[Disabled]


    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 800
    PCI Express Clock Drive.................: <<< 900
    CPU Clock Skew (ps)....................: <<< 0
    MCH Clock Skew (ps)...................: <<< 0


    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: [Auto]
    System Memory Multiplier ..............: 3.20B
    Memory Frequency (Mhz) ..............: 1066
    DRAM Timing Selectable ................: Manual

    Standard Timing Control
    CAS Latency Time........................5
    tRCD .........................................5
    tRP'...........................................5
    tRAS..........................................18

    Advanced Timing Control
    tRRD...........................................5
    tWTR..........................................12
    tWR............................................14
    tRFC...........................................68
    tRTP...........................................5
    Command Rate (CMD) ....................:2

    Driving Strength Profiles
    Driving Strength ............................1066

    Channel A
    Static tRead Value.........................:9
    tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Channel B
    Static tRead Value.........................:9
    tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................:1.175 AUto
    CPU Termination…..... 1.200V*.......: <<< See below comment (Set to stock for now)
    CPU PLL…………………....1.500V*.......: << 1.50 << Why so low? Stock is 1.5

    CPU Referen.…………....0.76V*.......: <<< .Auto


    MCH/ICH
    MCH Core…………….....1.100V...........: << 1.28
    MCH Reference….…….0.760V...........; <<< Leave
    MCH/DRAM Ref.…......0.900V...........: <<< Leave
    ICH I/O……………….....1.500V............: <<<1.55
    ICH Core…………...……1.100V............: <<< 1.14

    DRAM
    DRAM Voltage ……....1.800V............: 2.0-2.1
    DRAM Termination .…0.900V............: <<< Leave
    Channel A Reference 0.900V............: <<< Leave
    Channel B Reference 0.900V............: <<< Leave

    One question about your comments -
    "CPU Termination…..... 1.200V*.......: <<< See below comment (Set to stock for now)
    CPU PLL…………………....1.500V*.......: << 1.50 << Why so low? Stock is 1.5"
    Does this mean both of these should be set to 1.50? I have CPU Termination at 1.20V and CPU PLL at 1.5? << No, that means set PLL to stock.... BUt since you are at stock clocks then you can leave them both on auto.

    Vtt (Termination) would be Auto at stock as well, just both of those when you overclock any get way overvolted

Page 2 of 4 FirstFirst 1234 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •