Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 2 of 2 FirstFirst 12
Results 11 to 17 of 17

Thread: Need help with posting BIOS timings.




  1. #11
    Join Date
    Dec 2008
    Posts
    14

    Default Re: Need help with posting BIOS timings.

    Ok well this what I know.

    Ocz platinum pc2-8500 (1066) 5-5-5-15 at 2.1 v

    GAP45-UD3P

    Q9300 2.5ghz currently at 3.01ghz.

    I did a longer OCCT test of about 10 min and then I saw my temps reach 69. I'm sure any longer it would have made to 70.

    I used prime 95 and 2 of the cores failed, while the other two continued to test.

    I want to be as stable as possible at 3.0 ghz!

    You should know more than me I'm sure. So let me know where to start, if that means to load default settings in bios then so be it. I will appreciate your time and help. Thank you.

    When I get home I will post up my bios settings with voltage and so on.

  2. #12
    Join Date
    Apr 2008
    Posts
    942

    Default Re: Need help with posting BIOS timings.

    I suspect you are using the Intel stock cooler that came with your q9300? and sometimes they work very well. Depending on your ambient + case temperatures will determine as to what sort of overclock you can achieve without having to buy an aftermarket cooling solution.

    70C though is too high really and whilst OCCT/Prime95 etc loads your system more than it would normally see with everyday operation, it's still cutting it fine.

    Providing the stock cooler is fitted correctly, you shouldn't see the cores with Occt etc not really pass 60C at the stock 2.5Ghz frequency, unless your room temperature is really high. Until you get a better cooling solution I wouldn't recommend you overclock using the stock cooler.

    Also make sure you have the latest OCCT, or get HWmonitor as it's been updated to read Coretemps more accurately due to Intel releasing the data recently.
    GA-P35C-DS3R Rev2.0 F11 bios, E8200 (@3.0Ghz), OCZ DDR3 PC3-10666 Reaper 4GB (@1200Mhz), Xonar D1, 8800GTS 512, Corsair HX520 (Single 12volt line, Max 40A), WDC 3200aaks/5000aaks in AHCI mode, Vista 64 Premium.

  3. #13
    Join Date
    Dec 2008
    Posts
    14

    Default Re: Need help with posting BIOS timings.

    What cooler do you recommend that will be easy to install. The stock cooler was a slight pain. I will put my bios back to default, and try my testing again at 2.5 ghz instead of 3. If the temps are stiill bad I will know its the cooler. Thank you for your help, I will keep you posted.

  4. #14
    Join Date
    Apr 2008
    Posts
    942

    Default Re: Need help with posting BIOS timings.

    I wouldn't really want to recommend a cooler as there are so many of them and everyones got an opinion as to whats the best.

    It usually though comes down to either you want quietness, or you want a fantastic cooling solution. Most overclockers opt for somewhere in the middle and that means some of the Heatsinks are large.

    Ideally it's best to fit a cooler when the motherboard is out of the case and use the type that has a stengthening backplate. However the Intel design is designed for simplicity (supposedly) and you can remove the HSF whilst the Motherboard is in situe. Fitting though a pushpin HSF (cooler) whilst the motherboard is still in situe is a task in itself and not good for the impatient!
    GA-P35C-DS3R Rev2.0 F11 bios, E8200 (@3.0Ghz), OCZ DDR3 PC3-10666 Reaper 4GB (@1200Mhz), Xonar D1, 8800GTS 512, Corsair HX520 (Single 12volt line, Max 40A), WDC 3200aaks/5000aaks in AHCI mode, Vista 64 Premium.

  5. #15
    Join Date
    Dec 2008
    Posts
    14

    Default Re: Need help with posting BIOS timings.

    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Auto
    CPU Clock Ratio ..........................: 7
    Fine CPU Clock Ratio.....................:.5
    CPU Frequency ...........................: 2.5ghz


    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Disabled]
    CPU Host Frequency (Mhz) ............: 333 Mhz
    PCI Express Frequency (Mhz) .........: Auto

    C.I.A.2 .................................:[Disabled]


    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: 800mV <<<
    PCI Express Clock Drive.................: 900mV <<<
    CPU Clock Skew (ps)....................: 0ps<<<
    MCH Clock Skew (ps)...................: 0ps<<<


    DRAM Performance Control
    Performance Enhance...................: [Turbo]
    Extreme Memory Profile (X.M.P.).....: Auto
    (G)MCH Frequency Latch...............: [Auto]
    System Memory Multiplier ..............: Auto
    Memory Frequency (Mhz) ..............: 1066
    DRAM Timing Selectable ................: [Auto]

    Standard Timing Control
    CAS Latency Time........................ 5
    tRCD ......................................... 5
    tRP'........................................... 5
    tRAS.......................................... 15

    Set all Suggested below to highest Values first. Then later you can lower, one at a time, testing as you go

    Advanced Timing Control
    tRRD........................................... 4
    tWTR.......................................... 4
    tWR............................................ 6
    tRFC........................................... 72
    tRTP........................................... 4
    Command Rate (CMD) ....................: 0

    Driving Strength Profiles
    Driving Strength ............................

    Channel A
    Static tRead Value.........................: 11
    tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 6
    Twr2wr(Different Rank)...................:Auto 6
    Twr2rd(Different Rank)...................:Auto 5
    Trd2wr(Same/Diff Rank)..................:Auto 8
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Channel B
    Static tRead Value.........................: 11
    tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 6
    Twr2wr(Different Rank)...................:Auto 6
    Twr2rd(Different Rank)...................:Auto 5
    Trd2wr(Same/Diff Rank)..................:Auto 8
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Motherboard Voltage Control
    Voltage Type.... Auto
    CPU
    CPU Vcore….……….........................: 1.18750V
    CPU Termination…..... 1.200V*.......: <<< Leave
    CPU PLL…………………....1.500V*.......: << Please set to stock, Auto overvolts this way to much

    CPU Referen.…………...........: 0.760V

    CPU Reference2………,,0.800V*.......: ?

    MCH/ICH
    MCH Core…………….....1.100V...........: 1.100V
    MCH Reference….…….0.800V...........; 0.760V
    MCH/DRAM Ref.…......0.900V...........: 0.900V
    ICH I/O……………….....1.550V............: 1.500V
    ICH Core…………...……1.100V............: 1.100V

    DRAM
    DRAM Voltage ……....1.800V............: 2.1V
    DRAM Termination .…0.900V............: 0.900V
    Channel A Reference 0.900V............: 0.900V
    Channel B Reference 0.900V............: 0.900V

    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Enabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Enabled]
    Virtualization Technology................: [Enabled] Enabled if you use Vmware/Virtual PC
    </pre>

  6. #16
    Join Date
    Dec 2008
    Posts
    14

    Default Re: Need help with posting BIOS timings.

    I have a Freezer 7 Pro, Temps at BIOS ideal at 24c.
    in Windows im at 36c/39c jumps because my cpu is clocking from 2ghz to 2.5ghz.


    I would like to reach 3.2ghz Stable.

    Please let me know what to change. Thank you


    MOBO = P45-UD3P BIOS= F4
    CPU = Q9300 @ 2.5ghz
    Memory = OCZ Platinum PC8500 / 5-5-5-15 @2.1v 1066
    Cooler= Freezer 7 Pro
    PSU= 500 NEO Antec
    Last edited by Novanosis; 01-18-2009 at 11:06 AM.

  7. #17
    Join Date
    Dec 2008
    Posts
    14

    Default Re: Need help with posting BIOS timings.

    Bump!

Page 2 of 2 FirstFirst 12

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •