Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Results 1 to 3 of 3

Thread: Cannot start at 3.23 but ok at 2.97




  1. #1
    Join Date
    Jul 2008
    Posts
    75

    Default Cannot start at 3.23 but ok at 2.97

    I tried to change the CPU Host Frequency from its default to 360 it did not work but works at 351... do I need to tweak the DRAM area to reach higher?


    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............:
    CPU Clock Ratio ..........................:
    Fine CPU Clock Ratio.....................:.0
    CPU Frequency ...........................:


    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled]
    CPU Host Frequency (Mhz) ............: Mhz
    PCI Express Frequency (Mhz) .........:Set to 100

    C.I.A.2 .................................:[Disabled]


    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<<
    PCI Express Clock Drive.................: <<<
    CPU Clock Skew (ps)....................: <<<
    MCH Clock Skew (ps)...................: <<<


    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: [Auto]
    System Memory Multiplier ..............: Auto
    Memory Frequency (Mhz) ..............:
    DRAM Timing Selectable ................: [Manual]

    Standard Timing Control
    CAS Latency Time........................ 5
    tRCD ......................................... 5
    tRP'........................................... 5
    tRAS.......................................... 15

    Advanced Timing Control
    tRRD........................................... 4 Auto
    tWTR.......................................... 4 Auto
    tWR............................................13 Auto
    tRFC........................................... 68 Auto
    tRTP........................................... 4 Auto
    Command Rate (CMD) ....................:0 Auto

    Driving Strength Profiles
    Driving Strength ............................

    Channel A
    Static tRead Value.........................:7-10
    tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Channel B
    Static tRead Value.........................:7-10
    tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................:
    CPU Termination…..... 1.200V*.......: <<< Leave
    CPU PLL…………………....1.500V*.......: << Please set to stock, Auto overvolts this way to much

    CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly

    CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly

    MCH/ICH
    MCH Core…………….....1.100V...........: <<
    MCH Reference….…….0.800V...........; <<< Leave
    MCH/DRAM Ref.…......0.900V...........: <<< Leave
    ICH I/O……………….....1.550V............: <<< Leave
    ICH Core…………...……1.100V............: <<< Leave

    DRAM
    DRAM Voltage ……....1.800V............: 2.000V
    DRAM Termination .…0.900V............: <<< Leave
    Channel A Reference 0.900V............: <<< Leave
    Channel B Reference 0.900V............: <<< Leave

    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC

    Integrated Peripherals
    Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB
    CPU Type QuadCore Intel Core i7-4790K, 4200 MHz (42 x 100)
    Motherboard Name Gigabyte GA-Z97M-D3H
    (2 PCI, 2 PCI-E x16, 4 DDR3 DIMM, Audio, Video, Gigabit LAN)
    Motherboard Chipset Intel Wildcat Point Z97,
    Intel Haswell System Memory 16269 MB
    (DDR3-1333 DDR3 SDRAM)
    DIMM1: Corsair Vengeance Pro CMY16GX3M2A2400C11 8 GB DDR3-1333 DDR3 SDRAM (9-9-9-24 @ 666 MHz) (8-8-8-22 @ 609 MHz) (6-6-6-17 @ 457 MHz) (5-5-5-14 @ 380 MHz)
    DIMM3: Corsair Vengeance Pro CMY16GX3M2A2400C11 8 GB DDR3-1333 DDR3 SDRAM (9-9-9-24

  2. #2
    Join Date
    Jul 2008
    Posts
    75

    Default Re: Cannot start at 3.23 but ok at 2.97

    Now I followed everything in here and was able to boot up to 3.57ghz using the q9550 with Gskill DDR2 1066 memory. Somehow I think it is not stable although it boots up using Vista Ultimate with SP1. I will try to do a memtest or whatever utility for a few days just to see... as of now it is ok. CPU temperature in PC health is 27C???? I thought it would be way higher.... I had installed a few others like Oracle 10g and running a few nested queries and it seems to be fast. Below bios is what I had from some super gurus I found here and just use it as a template.... b4 I was not even able to boot up at 3.01 but after using and slowly changing the below settings I was able to boot up at 3.57.... kinda worried to push a little more to 3.6 even as I have a lot of queries to test... just no time to mess with the bios... bad economy... must work to earn and learn more.

    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Auto
    CPU Clock Ratio ..........................: 8x
    Fine CPU Clock Ratio.....................:.0.5
    CPU Frequency ...........................: 3.57 (420 x 8.5)


    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled]
    CPU Host Frequency (Mhz) ............: 420Mhz
    PCI Express Frequency (Mhz) .........:Set to 100

    C.I.A.2 .................................:[Disabled]


    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: 800<<<
    PCI Express Clock Drive.................: 900<<<
    CPU Clock Skew (ps)....................: 100<<<
    MCH Clock Skew (ps)...................: 150<<<


    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: [Auto]
    System Memory Multiplier ..............: 2.00D
    Memory Frequency (Mhz) ..............: [1066] 840
    DRAM Timing Selectable ................: [Manual]

    Standard Timing Control
    CAS Latency Time........................ 5 [5]
    tRCD ......................................... 7 [5]
    tRP'...........................................7 [5]
    tRAS.......................................... 20 [15]

    Advanced Timing Control
    tRRD........................................... 4 [4]
    tWTR.......................................... 4 [5]
    tWR............................................ 8 [10]
    tRFC...........................................68 [70]
    tRTP........................................... 4 [6]
    Command Rate (CMD) ....................: 8 [2]

    Driving Strength Profiles
    Driving Strength ............................Auto>> mine @ auto [800-1066]

    Channel A
    Static tRead Value.........................:11 [9] example: 6/7-10 333/B MCH (9-12 400/D MCH)

    tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Channel B
    Static tRead Value.........................:11 [9] example: 6/7-10 333/B MCH (9-12 400/D MCH)

    tRD Phase0 Adjustment...................:<<< Leave for all below as well - Mine all auto below
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................: 1.25000v [Auto]
    CPU Termination…..... 1.200V*.......: 1.2000v [1.24oV] <<< 1.2-1.38
    CPU PLL…………………....1.500V*.......: [Auto] << Please set to stock, Auto overvolts this way to much

    CPU Referen.…………....0.755V*.......: [Auto] <<< .64% Of Vtt (Termination above) Auto Will set this correctly

    CPU Reference2………,,0.800V*.......:[Auto] <<< .67% Of Vtt (Termination above) Auto Will set this correctly

    MCH/ICH
    MCH Core…………….....1.100V...........: 1.1000v [1.2400v] << 1.25-1.35
    MCH Reference….…….0.800V...........;0.760v [0.825v] <<< Leave
    MCH/DRAM Ref.…......0.900V...........: 0.900v [Auto] <<< Leave
    ICH I/O……………….....1.550V............: 1.500v [Auto]<<< 1.55-1.6
    ICH Core…………...……1.100V............: 1.1 [Auto]<<< 1.1x-1.2

    DRAM
    DRAM Voltage ……....1.800V............: 1.8000v [2.100v] 2.0-2.1 (Normally, check your ram sticker or wait till you link me and I will advise)
    DRAM Termination .…0.900V............: 0.900v [Auto]<<< Leave
    Channel A Reference 0.900V............: 0.900v [Auto] <<< Leave
    Channel B Reference 0.900V............: 0.900c [Auto] <<< Leave

    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Enabled] if you use Vmware/Virtual PC ..... [Enabled]
    The rest at default or whatever it was...

    Integrated Peripherals
    Whatever I had
    Last edited by pectin232; 12-22-2008 at 02:40 AM.
    CPU Type QuadCore Intel Core i7-4790K, 4200 MHz (42 x 100)
    Motherboard Name Gigabyte GA-Z97M-D3H
    (2 PCI, 2 PCI-E x16, 4 DDR3 DIMM, Audio, Video, Gigabit LAN)
    Motherboard Chipset Intel Wildcat Point Z97,
    Intel Haswell System Memory 16269 MB
    (DDR3-1333 DDR3 SDRAM)
    DIMM1: Corsair Vengeance Pro CMY16GX3M2A2400C11 8 GB DDR3-1333 DDR3 SDRAM (9-9-9-24 @ 666 MHz) (8-8-8-22 @ 609 MHz) (6-6-6-17 @ 457 MHz) (5-5-5-14 @ 380 MHz)
    DIMM3: Corsair Vengeance Pro CMY16GX3M2A2400C11 8 GB DDR3-1333 DDR3 SDRAM (9-9-9-24

  3. #3
    Join Date
    Jul 2008
    Posts
    75

    Default Re: Cannot start at 3.23 but ok at 2.97

    I thought a memory had to be like 5, 5, 5 15 but mine is all messed up.... will there be a problem with this settings? Seriously how far can this config be pushed to? Kinda nice to boot up so quick and doing simple photoshop sharpen on large jpg files so fast.
    CPU Type QuadCore Intel Core i7-4790K, 4200 MHz (42 x 100)
    Motherboard Name Gigabyte GA-Z97M-D3H
    (2 PCI, 2 PCI-E x16, 4 DDR3 DIMM, Audio, Video, Gigabit LAN)
    Motherboard Chipset Intel Wildcat Point Z97,
    Intel Haswell System Memory 16269 MB
    (DDR3-1333 DDR3 SDRAM)
    DIMM1: Corsair Vengeance Pro CMY16GX3M2A2400C11 8 GB DDR3-1333 DDR3 SDRAM (9-9-9-24 @ 666 MHz) (8-8-8-22 @ 609 MHz) (6-6-6-17 @ 457 MHz) (5-5-5-14 @ 380 MHz)
    DIMM3: Corsair Vengeance Pro CMY16GX3M2A2400C11 8 GB DDR3-1333 DDR3 SDRAM (9-9-9-24

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •