Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Results 1 to 3 of 3

Thread: 3.57 ghz with q9550 + GSkill DDR2 1066 ok!!




  1. #1
    Join Date
    Jul 2008
    Posts
    75

    Default 3.57 ghz with q9550 + GSkill DDR2 1066 ok!!

    With the following template from the mods here... thanks a lot... I am not sure if I can push to 3.6... but kinda worried.


    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Auto
    CPU Clock Ratio ..........................: 8x
    Fine CPU Clock Ratio.....................:.0.5
    CPU Frequency ...........................: 3.57 (420 x 8.5)


    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled]
    CPU Host Frequency (Mhz) ............: 420Mhz
    PCI Express Frequency (Mhz) .........:Set to 100

    C.I.A.2 .................................:[Disabled]


    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: 800<<<
    PCI Express Clock Drive.................: 900<<<
    CPU Clock Skew (ps)....................: 100<<<
    MCH Clock Skew (ps)...................: 150<<<


    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: [Auto]
    System Memory Multiplier ..............: 2.00D
    Memory Frequency (Mhz) ..............: [1066] 840
    DRAM Timing Selectable ................: [Manual]

    Standard Timing Control
    CAS Latency Time........................ 5 [5]
    tRCD ......................................... 7 [5]
    tRP'...........................................7 [5]
    tRAS.......................................... 20 [15]

    Advanced Timing Control
    tRRD........................................... 4 [4]
    tWTR.......................................... 4 [5]
    tWR............................................ 8 [10]
    tRFC...........................................68 [70]
    tRTP........................................... 4 [6]
    Command Rate (CMD) ....................: 8 [2]

    Driving Strength Profiles
    Driving Strength ............................Auto>> mine @ auto [800-1066]

    Channel A
    Static tRead Value.........................:11 [9] example: 6/7-10 333/B MCH (9-12 400/D MCH)

    tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Channel B
    Static tRead Value.........................:11 [9] example: 6/7-10 333/B MCH (9-12 400/D MCH)

    tRD Phase0 Adjustment...................:<<< Leave for all below as well - Mine all auto below
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................: 1.25000v [Auto]
    CPU Termination…..... 1.200V*.......: 1.2000v [1.24oV] <<< 1.2-1.38
    CPU PLL…………………....1.500V*.......: [Auto] << Please set to stock, Auto overvolts this way to much

    CPU Referen.…………....0.755V*.......: [Auto] <<< .64% Of Vtt (Termination above) Auto Will set this correctly

    CPU Reference2………,,0.800V*.......:[Auto] <<< .67% Of Vtt (Termination above) Auto Will set this correctly

    MCH/ICH
    MCH Core…………….....1.100V...........: 1.1000v [1.2400v] << 1.25-1.35
    MCH Reference….…….0.800V...........;0.760v [0.825v] <<< Leave
    MCH/DRAM Ref.…......0.900V...........: 0.900v [Auto] <<< Leave
    ICH I/O……………….....1.550V............: 1.500v [Auto]<<< 1.55-1.6
    ICH Core…………...……1.100V............: 1.1 [Auto]<<< 1.1x-1.2

    DRAM
    DRAM Voltage ……....1.800V............: 1.8000v [2.100v] 2.0-2.1 (Normally, check your ram sticker or wait till you link me and I will advise)
    DRAM Termination .…0.900V............: 0.900v [Auto]<<< Leave
    Channel A Reference 0.900V............: 0.900v [Auto] <<< Leave
    Channel B Reference 0.900V............: 0.900c [Auto] <<< Leave

    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Enabled] if you use Vmware/Virtual PC ..... [Enabled]
    The rest at default or whatever it was...

    Integrated Peripherals
    Whatever I had
    CPU Type QuadCore Intel Core i7-4790K, 4200 MHz (42 x 100)
    Motherboard Name Gigabyte GA-Z97M-D3H
    (2 PCI, 2 PCI-E x16, 4 DDR3 DIMM, Audio, Video, Gigabit LAN)
    Motherboard Chipset Intel Wildcat Point Z97,
    Intel Haswell System Memory 16269 MB
    (DDR3-1333 DDR3 SDRAM)
    DIMM1: Corsair Vengeance Pro CMY16GX3M2A2400C11 8 GB DDR3-1333 DDR3 SDRAM (9-9-9-24 @ 666 MHz) (8-8-8-22 @ 609 MHz) (6-6-6-17 @ 457 MHz) (5-5-5-14 @ 380 MHz)
    DIMM3: Corsair Vengeance Pro CMY16GX3M2A2400C11 8 GB DDR3-1333 DDR3 SDRAM (9-9-9-24

  2. #2
    Join Date
    Jul 2008
    Location
    Boston,MA
    Posts
    78

    Default Re: 3.57 ghz with q9550 + GSkill DDR2 1066 ok!!

    These look very loose to me.I think you may be able to tighten those up a lot.Are you running them at 840 or 1066?
    Standard Timing Control
    CAS Latency Time........................ 5 [5]
    tRCD ......................................... 7 [5]
    tRP'...........................................7 [5]
    tRAS.......................................... 20 [15]

    Advanced Timing Control
    tRRD........................................... 4 [4]
    tWTR.......................................... 4 [5]
    tWR............................................ 8 [10]
    tRFC...........................................68 [70]
    tRTP........................................... 4 [6]
    Command Rate (CMD) ....................: 8 [2]
    [SIGPIC][/SIGPIC]
    CoolerMaster 932haf
    ASUS P6T DELUVE V2
    Inte I7 920-4.0/4.2
    CoolIt DOMINO A.L.C
    CoolIt DualBay Gpu Cooler
    ASUS 4870-815/1050(crossfire)
    OCZ Platinum6GB DDR3-1600
    WesternDigtal VelociRaptor 300gb
    Corsair THX 750watt
    Vista Premium64sp2
    3DMARK06:28,515
    3DMARK VANTAGE 20,006

  3. #3
    Join Date
    Jul 2008
    Posts
    75

    Default Re: 3.57 ghz with q9550 + GSkill DDR2 1066 ok!!

    How to I tighten it? Using smaller values? By doing so what can I achieve.. sorry as I am not sure.... I thought if it runs now at 3.61 or 2 it should be good... do you imply that by tightening it I can maybe even push it to a 3.8ghz for the q9550 E0 stepping? Do advise
    CPU Type QuadCore Intel Core i7-4790K, 4200 MHz (42 x 100)
    Motherboard Name Gigabyte GA-Z97M-D3H
    (2 PCI, 2 PCI-E x16, 4 DDR3 DIMM, Audio, Video, Gigabit LAN)
    Motherboard Chipset Intel Wildcat Point Z97,
    Intel Haswell System Memory 16269 MB
    (DDR3-1333 DDR3 SDRAM)
    DIMM1: Corsair Vengeance Pro CMY16GX3M2A2400C11 8 GB DDR3-1333 DDR3 SDRAM (9-9-9-24 @ 666 MHz) (8-8-8-22 @ 609 MHz) (6-6-6-17 @ 457 MHz) (5-5-5-14 @ 380 MHz)
    DIMM3: Corsair Vengeance Pro CMY16GX3M2A2400C11 8 GB DDR3-1333 DDR3 SDRAM (9-9-9-24

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •