Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Results 1 to 6 of 6

Thread: Ga-ep45-ud3p memory help




  1. #1
    Join Date
    Jan 2009
    Posts
    30

    Default Ga-ep45-ud3p memory help

    Hi
    Im a bit of a newbie so i appologise now
    have run memtest and keep getting problems i am using 8 gig of corsair DDR2 XMS2 PC2-6400C5 TwinX (2x2GB could someone please tell me what to alter ie timmings and voltage to make it stable i just dont know what i have to adjust, cpu z says its 5 5 5 18 but i have no idea what to alter or what to alter it too any help would be so much appreciated

  2. #2
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Ga-ep45-ud3p memory help

    Please give us a link to your ram, and then fill this out with what you are using >>>

    Also let us know what CPU you have

    This is Just a template I use to ask people their settings, pay no attention to the numbers in it, replace with yours

    Code:
    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: 
    CPU Clock Ratio ..........................: 
    Fine CPU Clock Ratio.....................:.0
    CPU Frequency ...........................: 
    
    
    Clock Chip Control 
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled] 
    CPU Host Frequency (Mhz) ............: Mhz
    PCI Express Frequency (Mhz) .........:Set to 100
    
    C.I.A.2 .................................:[Disabled]
    
    
    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 
    PCI Express Clock Drive.................: <<< 
    CPU Clock Skew (ps)....................: <<< 
    MCH Clock Skew (ps)...................: <<< 
    
    
    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: [Auto]
    System Memory Multiplier ..............: 
    Memory Frequency (Mhz) ..............: 
    DRAM Timing Selectable ................: [Manual]
    
    Standard Timing Control
    CAS Latency Time........................
    tRCD .........................................
    tRP'...........................................
    tRAS..........................................
    
    Set all Suggested below to highest Values first.  Then later you can lower, one at a time, testing as you go
    
    Advanced Timing Control
    tRRD...........................................
    tWTR..........................................
    tWR............................................
    tRFC...........................................
    tRTP...........................................
    Command Rate (CMD) ....................:2
    
    Driving Strength Profiles
    Driving Strength ............................
    
    Channel A
    Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
     tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
     tRD Phase2 Adjustment .................:Auto
     tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 
    Twr2wr(Different Rank)...................:Auto 
    Twr2rd(Different Rank)...................:Auto 
    Trd2wr(Same/Diff Rank)..................:Auto 
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
    
    Channel B
    Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
     tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
     tRD Phase2 Adjustment .................:Auto
     tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 
    Twr2wr(Different Rank)...................:Auto 
    Twr2rd(Different Rank)...................:Auto 
    Trd2wr(Same/Diff Rank)..................:Auto 
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
    
    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................:
    CPU Termination…..... 1.200V*.......: <<< Leave
    CPU PLL…………………....1.500V*.......: << Please set to stock, Auto overvolts this way to much
    
    CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly 
    
    CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly 
    
    MCH/ICH
    MCH Core…………….....1.100V...........: << 
    MCH Reference….…….0.800V...........; <<< Leave
    MCH/DRAM Ref.…......0.900V...........: <<< Leave
    ICH I/O……………….....1.550V............: <<< Leave
    ICH Core…………...……1.100V............: <<< Leave
    
    DRAM
    DRAM Voltage ……....1.800V............: 
    DRAM Termination .…0.900V............: <<< Leave
    Channel A Reference 0.900V............: <<< Leave
    Channel B Reference 0.900V............: <<< Leave
    
    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC
    
    Integrated Peripherals
    Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB

  3. #3
    Join Date
    Jan 2009
    Posts
    30

    Default Re: Ga-ep45-ud3p memory help

    Hi here is the form you wanted thanks for responding
    _MB Intelligent Tweaker(M.I.T.)_*
    Robust Graphics Booster .AUTO..............:
    CPU Clock Ratio ..............8X............:
    Fine CPU Clock Ratio...........+0.5..........:.0
    CPU Frequency ..........2.83GHz(333X8.5.................:


    *_Clock Chip Control _*
    *_Standard Clock Control_*
    CPU Host Clock Control..................: [DISABLED]
    CPU Host Frequency (Mhz) ............: 333(Mhz)
    *PCI Express Frequency (Mhz) ..AUTO.......:Set to 100*

    C.I.A.2 .................................:[Disabled]


    *_Advanced Clock Control [Press Enter]_*
    CPU Clock Drive.....800mV......................: <<<
    PCI Express Clock Drive.....900mV............: <<<
    CPU Clock Skew (ps).......0ps.............: <<<
    MCH Clock Skew (ps)...........0ps........: <<<


    *_DRAM Performance Control_*
    *Performance Enhance..TURBO.................:
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: [Auto]
    System Memory Multiplier ..(SPD) AUTO............:
    Memory Frequency (Mhz) ...800 800...........:
    DRAM Timing Selectable .(SPD) AUTO...............:

    *Standard Timing Control*
    CAS Latency Time.......5 AUTO.................
    tRCD .........5 AUTO................................
    tRP'..............5 AUTO.............................
    tRAS.............18 AUTO.............................

    Set all Suggested below to highest Values first. Then later you can lower, one at a time, testing as you go

    *_Advanced Timing Control_*
    tRRD.........3 AUTO..................................
    tWTR.........3 AUTO.................................
    tWR.........6 AUTO...................................
    tRFC...........42 AUTO...............................
    tRTP...............3 AUTO............................
    Command Rate (CMD) ...0 AUTO.................:2

    _*Driving Strength Profiles*_
    Driving Strength ........AUTO....................

    *Channel A*
    Static tRead Value..7 AUTO.......................:6/7-10 333/B MCH - 8/9-12 400/D MCH
    tRD Phase0 Adjustment.....0 ..............:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment........0...........:Auto
    tRD Phase2 Adjustment .........0........:Auto
    tRD Phase3 Adjustment............0......:Auto
    Trd2rd(Different Rank)................6....:Auto
    Twr2wr(Different Rank).................6..:Auto
    Twr2rd(Different Rank).....5..............:Auto
    Trd2wr(Same/Diff Rank).....8.............:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    *Channel B*
    Static tRead Value......7 AUTO...................:6/7-10 333/B MCH - 8/9-12 400/D MCH
    tRD Phase0 Adjustment.........0..........:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...........0........:Auto
    tRD Phase2 Adjustment ............0.....:Auto
    tRD Phase3 Adjustment...............0...:Auto
    Trd2rd(Different Rank)........6............:Auto
    Twr2wr(Different Rank)........6...........:Auto
    Twr2rd(Different Rank)...........5........:Auto
    Trd2wr(Same/Diff Rank)...........8.......:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    *_Motherboard Voltage Control_*
    Voltage Type.…NORMAL CURRENT……...
    *CPU*
    CPU Vcore….…1.25000V AUTO…….........................:
    CPU Termination…..... 1.200V*AUTO.......: <<< Leave
    CPU PLL…………………....1.500V*.AUTO......: << Please set to stock, Auto overvolts this way to much

    CPU Referen.…………....0.760V*.AUTO......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly

    CPU Reference2………,,.....:<<< .67% Of Vtt (Termination above) Auto Will set this correctly

    *MCH/ICH*
    MCH Core…………….....1.100V.AUTO..........: <<
    MCH Reference….……..0.760VAUTO.........; <<< Leave
    MCH/DRAM Ref.…......0.900VAUTO...........: <<< Leave
    ICH I/O……………….....1.500V.AUTO...........: <<< Leave
    ICH Core…………...……1.100V.AUTO...........: <<< Leave

    *DRAM*
    DRAM Voltage ……....1.800V..AUTO..........:
    DRAM Termination .…0.900V.AUTO...........: <<< Leave
    Channel A Reference 0.900V..AUTO..........: <<< Leave
    Channel B Reference 0.900V...AUTO.........: <<< Leave

    *_Advanced Settings_*
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [ENABLE]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [ENABLED]
    Virtualization Technology................: [ENABLED] Enabled if you use Vmware/Virtual PC

  4. #4
    Join Date
    Jan 2009
    Posts
    30

    Default Re: Ga-ep45-ud3p memory help

    hi the link to the memory is thishttp://www.corsairmemory.com/configurator/product_results.aspx?id=754031
    also i am using a q9550 cpu

  5. #5

    Default Re: Ga-ep45-ud3p memory help

    1st thing you need to do is set the mem voltage(Dram voltage) to the specs for that memory which says 2.1v in that link
    New Q9650, Gigabyte UD3P, 4GB OCZ Platinum, Asus TOP 4850, Antec TP3 550W, Vista 64 SP1/XP SP3.

    http://www.cardomain.com/ride/2641801

  6. #6
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: Ga-ep45-ud3p memory help

    Hmm, I answered you here, did you not remember you already had a similar post? Just asking, I forget all the time myself so dont feel bad if you did >>>

    http://forums.tweaktown.com/f69/ga-e...-memory-29727/

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •