Hello Everybody
This is my first official post Iam trying to oc my baby Ive read some tried my hand but could use some advice here are my settings thanks guys any help is appreciated.





BIOS Setting
MB Intelligent Tweaker(M.I.T.)

Robust Graphics Booster ...............: [Auto]
CPU Clock Ratio .......................: 9
Fine CPU Clock Ratio...................: +0.0
CPU Frequency .........................: 3.00GHz (333X9)

Clock Chip Control
Standard Clock Control
CPU Host Clock Control.................: [Enabled]
CPU Host Frequency (Mhz) ..............: 333
PCI Express Frequency (Mhz) ...........: 100
C.I.A.2 ...............................: [Disabled]


Advanced Clock Control [Press Enter]
CPU Clock Drive........................: 800mV
PCI Express Clock Drive................: 900mV
CPU Clock Skew (ps)....................: 50ps
MCH Clock Skew (ps)....................: 150ps


DRAM Performance Control
Performance Enhance....................: [STANDARD]
Extreme Memory Profile (X.M.P.)........: [Disabled]
(G)MCH Frequency Latch.................: [AUTO]
System Memory Multiplier ..............: 2.40B
Memory Frequency (Mhz) ................: 800
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time.......................: 4
tRCD ..................................: 4
tRP'...................................: 4
tRAS...................................: 12

Advanced Timing Control
tRRD...................................: 4
tWTR...................................: 5
tWR....................................: 5
tRFC...................................: 65
tRTP...................................: 3
Command Rate (CMD) ....................: 2

Driving Strength Profiles
Driving Strength ......................: 1066MHz

Channel A
Static tRead Value.....................: 8
tRD Phase0 Adjustment..................: 0 [AUTO]
tRD Phase1 Adjustment..................: 0 [AUTO]
tRD Phase2 Adjustment .................: 0 [AUTO]
tRD Phase3 Adjustment..................: 0 [AUTO]
Trd2rd(Different Rank).................: 8 [AUTO]
Twr2wr(Different Rank).................: 8 [AUTO]
Twr2rd(Different Rank).................: 7 [AUTO]
Trd2wr(Same/Diff Rank).................: 9 [AUTO]
Dimm1 Clock Skew Control...............: [AUTO]
Dimm2 Clock Skew Control...............: [AUTO]
DDR Write Training.....................: [AUTO]

Channel B
Static tRead Value.....................: 8
tRD Phase0 Adjustment..................: 0 [AUTO]
tRD Phase1 Adjustment..................: 0 [AUTO]
tRD Phase2 Adjustment .................: 0 [AUTO]
tRD Phase3 Adjustment..................: 0 [AUTO]
Trd2rd(Different Rank).................: 8 [AUTO]
Twr2wr(Different Rank).................: 8 [AUTO]
Twr2rd(Different Rank).................: 7 [AUTO]
Trd2wr(Same/Diff Rank).................: 9 [AUTO]
Dimm1 Clock Skew Control...............: [AUTO]
Dimm2 Clock Skew Control...............: [AUTO]
DDR Write Training.....................: [AUTO]


Motherboard Voltage Control
CPU
Load-Line Calibration..................: [Enabled]
CPU Vcore...................1.250v : 1.300v
CPU Termination...........1.200v: 1.220v
CPU PLL.......................1.500v: 1.310V
CPU Reference.............0.760v: [AUTO]


MCH/ICH
MCH Core.....................1.100v: 1.200V
MCH Reference............0.760v.: [AUTO]
MCH/DRAM Ref..........0.900v.: [AUTO]
ICH I/O........................1.500v: 1.500v
ICH Core......................1.100v: 1.100v




DRAM
DRAM Voltage...................1.800v.: 1.90v
DRAM Termination ......................: 0.900V [AUTO]
Channel A Reference....................: 0.900V [AUTO]
Channel B Reference ...................: 0.900V [AUTO]

Advanced Settings
Limit CPUID Max. to 3..................: [Disabled]
No-Execute Memory Protect..............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support...................: [Disabled]
x C4/C4E State Support.................: [Disabled]
CPU Thermal Monitor 2(TM2) ............: [Enabled]
CPU EIST Function......................: [Disabled]
Virtualization Technology..............: [Enabled]<!-- / message -->