Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 1 of 3 123 LastLast
Results 1 to 10 of 26

Thread: OCZ2RPR10661G on Gigabyte GA-EP43-DS3L




  1. #1
    Join Date
    Feb 2009
    Posts
    13

    Default OCZ2RPR10661G on Gigabyte GA-EP43-DS3L

    Hello.
    I'm having problem running OCZ Reaper HPC OCZ2RPR10661G on Gigabyte GA-EP43-DS3L, at 1066mhz speed.
    I tried all possbile timmings and voltages. Works only at Single-Channel mode. Otherwise, continous short beeps, or post beep and than machine restarts. At 800mhz Dual-Channel worksperfectly, even with "EXTREME".
    I'm using the latest stable bios - F8, afraid to try F9Alpha. I read alot of people having this problem, didn't notice a clear solution.
    Could you please help me?

  2. #2
    Join Date
    Feb 2009
    Posts
    13

    Default Re: OCZ2RPR10661G on Gigabyte GA-EP43-DS3L

    someone?
    Could be a problem with my PSU?
    It's 450W CORSAIR (VX). Also using HD4670 GPU, 1 SATA, CPU E52000....
    It's ok when I high voltage to 2.3 on 800mhz, but failed when trying 1066 dual...

  3. #3
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: OCZ2RPR10661G on Gigabyte GA-EP43-DS3L

    Can you please post me your exact FULL settings you are trying that fail and I will advise back.

    And please also tell me how much of this ram you have installed?

    And do you have a link to this ram as I am not finding that model # at the OCZ Site

    I don't think it is a PSU issue, likely just some memory or voltage settings you have wrong or Auto has wrong

    This is Just a template I use to ask people their settings, pay no attention to the numbers in it, replace with yours

    Code:
    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Auto or Fast
    CPU Clock Ratio ..........................: 
    Fine CPU Clock Ratio.....................:.0
    CPU Frequency ...........................: 
    
    
    Clock Chip Control 
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled] 
    CPU Host Frequency (Mhz) ............: Mhz
    PCI Express Frequency (Mhz) .........:Set to 100
    
    C.I.A.2 .................................:[Disabled]
    
    
    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 800
    PCI Express Clock Drive.................: <<< 900
    CPU Clock Skew (ps)....................: <<< 
    MCH Clock Skew (ps)...................: <<< 
    
    
    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: [Auto]
    System Memory Multiplier ..............: 
    Memory Frequency (Mhz) ..............: 
    DRAM Timing Selectable ................: [Manual]
    
    Standard Timing Control
    CAS Latency Time........................
    tRCD .........................................
    tRP'...........................................
    tRAS..........................................
    
    Set all Suggested below to highest Values first.  Then later you can lower, one at a time, testing as you go
    
    Advanced Timing Control
    tRRD...........................................
    tWTR..........................................
    tWR............................................
    tRFC...........................................
    tRTP...........................................
    Command Rate (CMD) ....................:2
    
    Driving Strength Profiles
    Driving Strength ............................
    
    Channel A
    Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
     tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
     tRD Phase2 Adjustment .................:Auto
     tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 
    Twr2wr(Different Rank)...................:Auto 
    Twr2rd(Different Rank)...................:Auto 
    Trd2wr(Same/Diff Rank)..................:Auto 
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
    
    Channel B
    Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
     tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
     tRD Phase2 Adjustment .................:Auto
     tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 
    Twr2wr(Different Rank)...................:Auto 
    Twr2rd(Different Rank)...................:Auto 
    Trd2wr(Same/Diff Rank)..................:Auto 
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
    
    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................:Auto if not overclocking, if you are overclocking please do find and set your own voltages
    
    CPU Termination…..... 1.200V*.......: << If overclocking Please set to stock, Auto overvolts this way to much.  Optimal range for overclock would be 1.2-1.5 depending on Vcore, try to keep at least .1 under vcore.  Auto is fine if not overclocking
    
    CPU PLL…………………....1.500V*.......: << If overclocking Please set to stock, Auto overvolts this way to much.  Optimal range for overclock would be 1.5-1.65.  Auto is fine if not overclocking
    
    CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly 
    
    CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly 
    
    MCH/ICH
    MCH Core…………….....1.100V...........: << 
    MCH Reference….…….0.800V...........; <<< Leave
    MCH/DRAM Ref.…......0.900V...........: <<< Leave
    ICH I/O……………….....1.550V............: <<< Leave
    ICH Core…………...……1.100V............: <<< Leave
    
    DRAM
    DRAM Voltage ……....1.800V............: 
    DRAM Termination .…0.900V............: <<< Leave
    Channel A Reference 0.900V............: <<< Leave
    Channel B Reference 0.900V............: <<< Leave
    
    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC
    
    Integrated Peripherals
    Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB

  4. #4
    Join Date
    Feb 2009
    Posts
    13

    Default Re: OCZ2RPR10661G on Gigabyte GA-EP43-DS3L

    I installed 2 GIGA. They all work O.K. seperetly at 1066, and also at single-mode.
    There it is: OCZ Technology | Products | Memory | OCZ DDR2 PC2-8500 Reaper HPC Edition

    Here's my settings:

    Code:
    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Auto 
    CPU Clock Ratio ..........................: 333 (also tried 266)
    Fine CPU Clock Ratio.....................:.0
    CPU Frequency ...........................: 9
     
     
    Clock Chip Control 
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled] 
    CPU Host Frequency (Mhz) ............: 333 Mhz (also 266)
    PCI Express Frequency (Mhz) .........:Set to 100
     
    C.I.A.2 .................................:[Disabled]
     
     
    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 800
    PCI Express Clock Drive.................: <<< 900
    CPU Clock Skew (ps)....................: <<< 
    MCH Clock Skew (ps)...................: <<< 
     
     
    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: [Auto]
    System Memory Multiplier ..............: 2.60B
    Memory Frequency (Mhz) ..............: 333
    DRAM Timing Selectable ................: [Manual]
     
    Standard Timing Control
    CAS Latency Time........................7 (from 5 to 15)
    tRCD .........................................7 (from 5 to 15)
    tRP'...........................................7 (from 5 to 15)
    tRAS..........................................22 (anything from 15 to 24)
     
    Set all Suggested below to highest Values first.  Then later you can lower, one at a time, testing as you go
     
    Advanced Timing Control
    tRRD...........................................autotWTR..........................................
    tWR............................................
    tRFC...........................................
    tRTP...........................................
    Command Rate (CMD) ....................:2
     
    Driving Strength Profiles
    Driving Strength ............................
     
    Channel A
    Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
     tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
     tRD Phase2 Adjustment .................:Auto
     tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 
    Twr2wr(Different Rank)...................:Auto 
    Twr2rd(Different Rank)...................:Auto 
    Trd2wr(Same/Diff Rank)..................:Auto 
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
     
    Channel B
    Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
     tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
     tRD Phase2 Adjustment .................:Auto
     tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 
    Twr2wr(Different Rank)...................:Auto 
    Twr2rd(Different Rank)...................:Auto 
    Trd2wr(Same/Diff Rank)..................:Auto 
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
     
    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................:Auto if not overclocking, if you are overclocking please do find and set your own voltages
     
    CPU Termination…..... 1.200V*.......: << If overclocking Please set to stock, Auto overvolts this way to much.  Optimal range for overclock would be 1.2-1.5 depending on Vcore, try to keep at least .1 under vcore.  Auto is fine if not overclocking
     
    CPU PLL…………………....1.500V*.......: << If overclocking Please set to stock, Auto overvolts this way to much.  Optimal range for overclock would be 1.5-1.65.  Auto is fine if not overclocking
     
    CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly 
     
    CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly 
     
    MCH/ICH
    MCH Core…………….....1.100V...........: << 
    MCH Reference….…….0.800V...........; <<< Leave
    MCH/DRAM Ref.…......0.900V...........: <<< Leave
    ICH I/O……………….....1.550V............: <<< Leave
    ICH Core…………...……1.100V............: <<< Leave
     
    DRAM
    DRAM Voltage ……....1.800V............: 
    DRAM Termination .…0.900V............: <<< Leave
    Channel A Reference 0.900V............: <<< Leave
    Channel B Reference 0.900V............: <<< Leave
     
    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC
     
    Integrated Peripherals
    Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB
    [/quote]

  5. #5
    Join Date
    Feb 2009
    Posts
    13

    Default Re: OCZ2RPR10661G on Gigabyte GA-EP43-DS3L

    This is the correct settings:

    Quote Originally Posted by kotvana View Post
    I installed 2 GIGA. They all work O.K. seperetly at 1066, and also at single-mode.
    There it is: OCZ Technology | Products | Memory | OCZ DDR2 PC2-8500 Reaper HPC Edition

    Here's my settings:

    Code:
    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Auto 
    CPU Clock Ratio ..........................: 333 (also tried 266)
    Fine CPU Clock Ratio.....................:.0
    CPU Frequency ...........................: 9
     
     
    Clock Chip Control 
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled] 
    CPU Host Frequency (Mhz) ............: 333 Mhz (also 266)
    PCI Express Frequency (Mhz) .........:Set to 100
     
    C.I.A.2 .................................:[Disabled]
     
     
    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 800
    PCI Express Clock Drive.................: <<< 900
    CPU Clock Skew (ps)....................: <<< 
    MCH Clock Skew (ps)...................: <<< 
     
     
    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: [Auto]
    System Memory Multiplier ..............: 2.60B
    Memory Frequency (Mhz) ..............: 333
    DRAM Timing Selectable ................: [Manual]
     
    Standard Timing Control
    CAS Latency Time........................7 (from 5 to 15)
    tRCD .........................................7 (from 5 to 15)
    tRP'...........................................7 (from 5 to 15)
    tRAS..........................................22 (anything from 15 to 24)
     
    Set all Suggested below to highest Values first.  Then later you can lower, one at a time, testing as you go
     
    Advanced Timing Control
    tRRD...........................................autotWTR..........................................
    tWR............................................
    tRFC...........................................
    tRTP...........................................
    Command Rate (CMD) ....................:2
     
    Driving Strength Profiles
    Driving Strength ............................
     
    Channel A
    Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
     tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
     tRD Phase2 Adjustment .................:Auto
     tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 
    Twr2wr(Different Rank)...................:Auto 
    Twr2rd(Different Rank)...................:Auto 
    Trd2wr(Same/Diff Rank)..................:Auto 
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
     
    Channel B
    Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
     tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
     tRD Phase2 Adjustment .................:Auto
     tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 
    Twr2wr(Different Rank)...................:Auto 
    Twr2rd(Different Rank)...................:Auto 
    Trd2wr(Same/Diff Rank)..................:Auto 
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
     
    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................:Auto if not overclocking, if you are overclocking please do find and set your own voltages
     
    CPU Termination…..... 1.200V*.......: << If overclocking Please set to stock, Auto overvolts this way to much.  Optimal range for overclock would be 1.2-1.5 depending on Vcore, try to keep at least .1 under vcore.  Auto is fine if not overclocking
     
    CPU PLL…………………....1.500V*.......: << If overclocking Please set to stock, Auto overvolts this way to much.  Optimal range for overclock would be 1.5-1.65.  Auto is fine if not overclocking
     
    CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly 
     
    CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly 
     
    MCH/ICH
    MCH Core…………….....1.100V...........: << from 1.100 to 1.400
    MCH Reference….…….0.800V...........; <<< Leave
    MCH/DRAM Ref.…......0.900V...........: <<< Leave
    ICH I/O……………….....1.550V............: <<< Leave
    ICH Core…………...……1.100V............: <<< Leave
     
    DRAM
    DRAM Voltage ……....1.800V............: from 1.800 to 2.40
    DRAM Termination .…0.900V............: <<< Leave
    Channel A Reference 0.900V............: <<< Leave
    Channel B Reference 0.900V............: <<< Leave
     
    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC
     
    Integrated Peripherals
    Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB
    [/quote]

  6. #6
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: OCZ2RPR10661G on Gigabyte GA-EP43-DS3L

    Ok, try these and see if you get any better results. This is for stock E5200, and 333 FSB I guess >>>

    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Auto or Fast
    CPU Clock Ratio ..........................: 333 (also tried 266) Either (333 may be better, if you know you have your CPU Voltage ect stable)

    Fine CPU Clock Ratio.....................:.0
    CPU Frequency ...........................: 9


    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled]
    CPU Host Frequency (Mhz) ............: 333 Mhz (also 266)
    PCI Express Frequency (Mhz) .........:Set to 100

    C.I.A.2 .................................:[Disabled]


    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 800
    PCI Express Clock Drive.................: <<< 900
    CPU Clock Skew (ps)....................: <<<
    MCH Clock Skew (ps)...................: <<<


    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: [Auto]
    System Memory Multiplier ..............: 2.60B ???? This is not a option! Use 4.00A for 266 FSB, and use 3.20B for 333 FSB)

    Memory Frequency (Mhz) ..............: 1066
    DRAM Timing Selectable ................: [Manual]

    Standard Timing Control
    CAS Latency Time........................5
    tRCD ........................................5
    tRP'...........................................5
    tRAS..........................................15/18

    Set all Suggested below to highest Values first. Then later you can lower, one at a time, testing as you go

    Advanced Timing Control
    tRRD...........................................3-4
    tWTR..........................................3-6
    tWR............................................4-6
    tRFC...........................................42-48
    tRTP...........................................3-5
    Command Rate (CMD) ....................:2

    Driving Strength Profiles
    Driving Strength ............................ 1066

    Channel A
    Static tRead Value.........................:6-10
    tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Channel B
    Static tRead Value.........................:6-10
    tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................:Auto if not overclocking, if you are overclocking please do find and set your own voltages

    CPU Termination…..... 1.200V*.......: << If overclocking Please set to stock, Auto overvolts this way to much. Optimal range for overclock would be 1.2-1.5 depending on Vcore, try to keep at least .1 under vcore. Auto is fine if not overclocking

    CPU PLL…………………....1.500V*.......: << If overclocking Please set to stock, Auto overvolts this way to much. Optimal range for overclock would be 1.5-1.65. Auto is fine if not overclocking

    CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly

    CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly

    MCH/ICH
    MCH Core…………….....1.100V...........: << try 1.24-1.26, and if no luck try 1.05
    MCH Reference….…….0.800V...........; <<< Leave
    MCH/DRAM Ref.…......0.900V...........: <<< Leave
    ICH I/O……………….....1.550V............: <<< 1.55
    ICH Core…………...……1.100V............: <<< 1.14

    DRAM
    DRAM Voltage ……....1.800V............: from 2.1v (If your ram sticker says 2.1V then you cannot use 2.2+ or your warranty will be void)

    2.1 - 2.3** Volts
    **Do not exceed 2.1V specification if listed on the module label
    OCZ Technology | Products | Memory | OCZ DDR2 PC2-8500 Reaper HPC Edition

    DRAM Termination .…0.900V............: <<< Leave
    Channel A Reference 0.900V............: <<< Leave
    Channel B Reference 0.900V............: <<< Leave

    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC

    Integrated Peripherals
    Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB

  7. #7
    Join Date
    Feb 2009
    Posts
    13

    Default Re: OCZ2RPR10661G on Gigabyte GA-EP43-DS3L

    I don't have the value "ICH Core", and MCH Core is only 1.1-1.4, with steps of 0.1 - can't make 1.24 or 1.26.
    I tried your suggestion and all I get is constant restrat.

    Quote Originally Posted by Lsdmeasap View Post
    Ok, try these and see if you get any better results. This is for stock E5200, and 333 FSB I guess >>>

    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Auto or Fast
    CPU Clock Ratio ..........................: 333 (also tried 266) Either (333 may be better, if you know you have your CPU Voltage ect stable)

    Fine CPU Clock Ratio.....................:.0
    CPU Frequency ...........................: 9


    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled]
    CPU Host Frequency (Mhz) ............: 333 Mhz (also 266)
    PCI Express Frequency (Mhz) .........:Set to 100

    C.I.A.2 .................................:[Disabled]


    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 800
    PCI Express Clock Drive.................: <<< 900
    CPU Clock Skew (ps)....................: <<<
    MCH Clock Skew (ps)...................: <<<


    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: [Auto]
    System Memory Multiplier ..............: 2.60B ???? This is not a option! Use 4.00A for 266 FSB, and use 3.20B for 333 FSB)

    Memory Frequency (Mhz) ..............: 1066
    DRAM Timing Selectable ................: [Manual]

    Standard Timing Control
    CAS Latency Time........................5
    tRCD ........................................5
    tRP'...........................................5
    tRAS..........................................15/18

    Set all Suggested below to highest Values first. Then later you can lower, one at a time, testing as you go

    Advanced Timing Control
    tRRD...........................................3-4
    tWTR..........................................3-6
    tWR............................................4-6
    tRFC...........................................42-48
    tRTP...........................................3-5
    Command Rate (CMD) ....................:2

    Driving Strength Profiles
    Driving Strength ............................ 1066

    Channel A
    Static tRead Value.........................:6-10
    tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Channel B
    Static tRead Value.........................:6-10
    tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................:Auto if not overclocking, if you are overclocking please do find and set your own voltages

    CPU Termination…..... 1.200V*.......: << If overclocking Please set to stock, Auto overvolts this way to much. Optimal range for overclock would be 1.2-1.5 depending on Vcore, try to keep at least .1 under vcore. Auto is fine if not overclocking

    CPU PLL…………………....1.500V*.......: << If overclocking Please set to stock, Auto overvolts this way to much. Optimal range for overclock would be 1.5-1.65. Auto is fine if not overclocking

    CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly

    CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly

    MCH/ICH
    MCH Core…………….....1.100V...........: << try 1.24-1.26, and if no luck try 1.05
    MCH Reference….…….0.800V...........; <<< Leave
    MCH/DRAM Ref.…......0.900V...........: <<< Leave
    ICH I/O……………….....1.550V............: <<< 1.55
    ICH Core…………...……1.100V............: <<< 1.14

    DRAM
    DRAM Voltage ……....1.800V............: from 2.1v (If your ram sticker says 2.1V then you cannot use 2.2+ or your warranty will be void)


    OCZ Technology | Products | Memory | OCZ DDR2 PC2-8500 Reaper HPC Edition

    DRAM Termination .…0.900V............: <<< Leave
    Channel A Reference 0.900V............: <<< Leave
    Channel B Reference 0.900V............: <<< Leave

    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC

    Integrated Peripherals
    Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB

  8. #8
    Join Date
    Feb 2009
    Posts
    13

    Default Re: OCZ2RPR10661G on Gigabyte GA-EP43-DS3L

    What could be the problem if it works perfectly Single mode?

  9. #9
    Join Date
    Feb 2009
    Posts
    13

    Default Re: OCZ2RPR10661G on Gigabyte GA-EP43-DS3L

    Just keep wondering what might be wrong....

  10. #10
    Join Date
    Feb 2009
    Location
    California
    Posts
    18

    Default Re: OCZ2RPR10661G on Gigabyte GA-EP43-DS3L

    Kotvana, did u solve your issue? i have the same mobo. and our tech.Angel hlpd me to solve mine w/my crucials 2x1GB modules i have 4gigs 1066 cl 5-5-5-15 2.2v i followed his devine recommendation to the book and i am stable (prime95) and not having the options you said too.
    ---------
    Mobo-EP-43-DS3L
    CPU-Core 2 Quad Q9550 2.83GHz
    Case- El Diablo from Tagan
    RAM- 4gigs (2x1GB) Modules ballistix 2.1v
    PSU- Thermaltake 850W thoughpower cable management
    HDD- 1 WD 120 gig / 1 Seagate 120 gig
    OS- Vista Home premium 32 bit
    Video card- EVGA GTX 260 896GB DDR3 drivers 182.06

Page 1 of 3 123 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •