Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Results 1 to 10 of 10

Thread: I need help




  1. #1
    Join Date
    Feb 2009
    Posts
    5

    Default I need help

    Hello i need that someone help me about a problem with my memories.
    My computer:

    -Gigabyte ep45 ds3r bios f10
    -2x2 gb kingston hiperx 1066
    -intel q6600@3200
    -sapphire radeon 4870
    -nox urano 600w

    My problem is that these memories dont work at 1066@5,5,5,15 with 2,2v because windows doesn´t start, only work at 800 very well including at 800@4,4,4,10.

    Sorry for my english.

  2. #2
    Join Date
    Jan 2009
    Location
    In. Usa
    Posts
    41

    Default Re: I need help

    raise mch
    E7400, Gigabyte P45-UD3P, 2gb Patriot PC28500,
    WD 320 gig HD, Sapphire 4670 DDR4, Corsair VX550
    Xigmatek HDT1283, Antec 300, Xp Pro 32bit

  3. #3

    Default Re: I need help

    you may need to tweak the mch ref value, but 1st try manually setting the PL(static tRead) to like 10. Then see if it boots. If not, try switching the mem stick positions, so 1>3 and 3>1, try it. If not Try 1 stick at a time and run memtest if it will boot fine with 1 stick at 1066
    New Q9650, Gigabyte UD3P, 4GB OCZ Platinum, Asus TOP 4850, Antec TP3 550W, Vista 64 SP1/XP SP3.

    http://www.cardomain.com/ride/2641801

  4. #4
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: I need help

    Ya, I would start with a high PL (Static tRead/tRD) at 9-10 and then add some MCH Voltage and set ram voltage to 2.1. Try MCH Core Voltage of 1.2-1.24 and see if that helps

    What FSB are you using for your CPU? This matters because you need to choose your memory multiplier based on this FSB Setting.

    Please to make it easier give us your full settings that are failing and a link to your ram or the model # and we will advise back >>>

    This is Just a template I use to ask people their settings, pay no attention to the numbers in it, replace with yours

    Code:
    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Auto or Fast
    CPU Clock Ratio ..........................: 
    Fine CPU Clock Ratio.....................:.0
    CPU Frequency ...........................: 
    
    
    Clock Chip Control 
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled] 
    CPU Host Frequency (Mhz) ............: Mhz
    PCI Express Frequency (Mhz) .........:Set to 100
    
    C.I.A.2 .................................:[Disabled]
    
    
    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 800
    PCI Express Clock Drive.................: <<< 900
    CPU Clock Skew (ps)....................: <<< 
    MCH Clock Skew (ps)...................: <<< 
    
    
    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: [Auto]
    System Memory Multiplier ..............: 
    Memory Frequency (Mhz) ..............: 
    DRAM Timing Selectable ................: [Manual]
    
    Standard Timing Control
    CAS Latency Time........................
    tRCD .........................................
    tRP'...........................................
    tRAS..........................................
    
    Set all Suggested below to highest Values first.  Then later you can lower, one at a time, testing as you go
    
    Advanced Timing Control
    tRRD...........................................
    tWTR..........................................
    tWR............................................
    tRFC...........................................
    tRTP...........................................
    Command Rate (CMD) ....................:2
    
    Driving Strength Profiles
    Driving Strength ............................
    
    Channel A
    Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
     tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
     tRD Phase2 Adjustment .................:Auto
     tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 
    Twr2wr(Different Rank)...................:Auto 
    Twr2rd(Different Rank)...................:Auto 
    Trd2wr(Same/Diff Rank)..................:Auto 
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
    
    Channel B
    Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
     tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
     tRD Phase2 Adjustment .................:Auto
     tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 
    Twr2wr(Different Rank)...................:Auto 
    Twr2rd(Different Rank)...................:Auto 
    Trd2wr(Same/Diff Rank)..................:Auto 
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
    
    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................:Auto if not overclocking, if you are overclocking please do find and set your own voltages
    
    CPU Termination…..... 1.200V*.......: << If overclocking Please set to stock, Auto overvolts this way to much.  Optimal range for overclock would be 1.2-1.5 depending on Vcore, try to keep at least .1 under vcore.  Auto is fine if not overclocking
    
    CPU PLL…………………....1.500V*.......: << If overclocking Please set to stock, Auto overvolts this way to much.  Optimal range for overclock would be 1.5-1.65.  Auto is fine if not overclocking
    
    CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly 
    
    CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly 
    
    MCH/ICH
    MCH Core…………….....1.100V...........: << 
    MCH Reference….…….0.800V...........; <<< Leave
    MCH/DRAM Ref.…......0.900V...........: <<< Leave
    ICH I/O……………….....1.550V............: <<< Leave
    ICH Core…………...……1.100V............: <<< Leave
    
    DRAM
    DRAM Voltage ……....1.800V............: 
    DRAM Termination .…0.900V............: <<< Leave
    Channel A Reference 0.900V............: <<< Leave
    Channel B Reference 0.900V............: <<< Leave
    
    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC
    
    Integrated Peripherals
    Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB

  5. #5
    Join Date
    Feb 2009
    Posts
    5

    Default Re: I need help

    This is my configuration in bios:

    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Auto
    CPU Clock Ratio ..........................: 8
    Fine CPU Clock Ratio.....................:.0(No)
    CPU Frequency ...........................: 3200(400x8)


    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled]
    CPU Host Frequency (Mhz) ............: 400 Mhz
    PCI Express Frequency (Mhz) .........:100

    C.I.A.2 .................................:[Disabled]


    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 700
    PCI Express Clock Drive.................: <<< 700
    CPU Clock Skew (ps)....................: <<< auto
    MCH Clock Skew (ps)...................: <<< auto


    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: Disabled(NO)
    (G)MCH Frequency Latch...............: 400
    System Memory Multiplier ..............: 2.66d
    Memory Frequency (Mhz) ..............: 1066
    DRAM Timing Selectable ................: [Manual]

    Standard Timing Control
    CAS Latency Time........................5
    tRCD .........................................5
    tRP'...........................................5
    tRAS..........................................15

    Set all Suggested below to highest Values first. Then later you can lower, one at a time, testing as you go

    Advanced Timing Control
    tRRD...........................................aut o
    tWTR..........................................auto
    tWR............................................aut o
    tRFC...........................................aut o
    tRTP...........................................aut o
    Command Rate (CMD) ....................:2

    Driving Strength Profiles
    Driving Strength ............................(no)

    Channel A
    Static tRead Value.........................:11
    tRD Phase0 Adjustment...................:Auto
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Channel B
    Static tRead Value.........................:11
    tRD Phase0 Adjustment...................:Auto
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Motherboard Voltage Control
    Voltage Type.………... manual
    CPU
    CPU Vcore….……….........................:1.32500

    CPU Termination…..... 1.200V*.......: 1.200

    CPU PLL…………………....1.500V*.......: 1.500

    CPU Referen.…………....0.755V*.......: auto

    CPU Reference2………,,0.800V*.......:auto

    MCH/ICH
    MCH Core…………….....1.100V...........: 1.260
    MCH Reference….…….0.800V...........; AUTO
    MCH/DRAM Ref.…......0.900V...........: auto
    ICH I/O……………….....1.550V............: auto
    ICH Core…………...……1.100V............: (no)

    DRAM
    DRAM Voltage ……....1.800V............: 2.2v
    DRAM Termination .…0.900V............: auto
    Channel A Reference 0.900V............: auto
    Channel B Reference 0.900V............: auto

    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [enabled]
    C2/C2E State Support....................: [Disabled](no)
    x C4/C4E State Support..................: [Disabled](no)
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Enabled]
    Virtualization Technology................: [enabled]

    Integrated Peripherals
    Legacy USB Storage Detect ..............[Disabled]

    Thank you
    Last edited by majr70; 02-28-2009 at 12:39 AM.

  6. #6
    Join Date
    Feb 2009
    Posts
    5

    Default Re: I need help


  7. #7
    Join Date
    Jan 2009
    Posts
    5

    Default Re: I need help

    Hy!
    This is the default settings:

    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 800
    PCI Express Clock Drive.................: <<< 900
    CPU Clock Skew (ps)....................: <<< auto
    MCH Clock Skew (ps)...................: <<< auto

    OC not work 700/700mV in Clock Drive settings.

    Sorry my bad english.

  8. #8
    Join Date
    Feb 2009
    Posts
    5

    Default Re: I need help

    Quote Originally Posted by szacsee View Post
    Hy!
    This is the default settings:

    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 800
    PCI Express Clock Drive.................: <<< 900
    CPU Clock Skew (ps)....................: <<< auto
    MCH Clock Skew (ps)...................: <<< auto

    OC not work 700/700mV in Clock Drive settings.

    Sorry my bad english.

    In this way doesn´t work. Windows don´t start.

    Anybody else have this motherboard and this memories working well at 5,5,5,15@1066?

    Thank you

  9. #9
    Join Date
    Feb 2009
    Posts
    5

    Default Re: I need help

    Quote Originally Posted by SpeedEuphoria View Post
    you may need to tweak the mch ref value, but 1st try manually setting the PL(static tRead) to like 10. Then see if it boots. If not, try switching the mem stick positions, so 1>3 and 3>1, try it. If not Try 1 stick at a time and run memtest if it will boot fine with 1 stick at 1066
    Hello, i have change the mem stick positions, 1 to 2 and 3 to 4 (red) and work fine at 5,5,5,15@1066. Do you think if the 1 and 3 positions are broken?
    Thaks and sorry for my little english

  10. #10
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: I need help

    Hmm, You will need to do some more testing to see if you have bad slots on your board.

    Please try with One stick of ram in slot 1, then 2, then 3, and then 4 to be sure all slots are ok.

    If they are you should be using 1+3 or 2+4 for Dual channel memory.

    About your Clock Drive voltage questions. You need to load and apply optimized defaults, then save and reboot back to the BIOS and they will be changed and working. Manually changing them may not work as many hidden settings will also be set incorrect since you loaded fail safe settings.

    So please load optimized, then save and apply and reboot back to the BIOS and then set all your settings again. DO NOT FORGET SATA and Other DISK Settings you WILL HAVE TO Set them all again before you load windows.

    Once you are sure you have working memory slots I can advise you about your settings

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •