Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Results 1 to 1 of 1

Thread: UD3 +GSkill 6400black PI limits.




  1. #1
    kick's Avatar
    kick is offline Senior Member
    Join Date
    Feb 2009
    Location
    Europe,the wild wild west.
    Posts
    1,223

    Question Gskill 6400+UD3 >?

    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster .................: [Auto]
    CPU Clock Ratio ............................: [7x]
    CPU Frequency .............................: 3.01GHz [3.5Ghz*]

    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control......................: [Enabled]
    CPU Host Frequency (Mhz) ................: [430][500*]
    PCI Express Frequency (Mhz) .............: 100
    C.I.A.2 ..........................................: [Disabled]

    Advanced Clock Control [Press Enter]
    CPU Clock Drive............................: [1000mV]auto*
    PCI Express Clock Drive..................: [1000mV]auto*
    CPU Clock Skew (ps).....................: [ 0 ps]
    MCH Clock Skew (ps).....................: [0 ps]

    DRAM Performance Control
    Performance Enhance........................: [Standard]turbo*
    (G)MCH Frequency Latch....................: [auto]
    System Memory Multiplier ..................: [2.40B]2.0B*
    Memory Frequency (Mhz) ...............: [1032]1000*
    DRAM Timing Selectable ..................: [Manual]

    Standard Timing Control
    CAS Latency Time....................... [5]5*
    tRCD ........................................ [5]5*
    tRP'.......................................... [4/5]5*
    tRAS....................................... [15/18]15*

    Advanced Timing Control
    tRRD................................... [Auto]
    tWTR................................... [Auto]
    tWR.................................... [Auto]
    tRFC................................... [Auto/66 shown in memset]48/52*
    tRTP................................... [Auto]
    Command Rate (CMD) ....................[2T]




    Driving Strength Profiles
    Driving Strength .........................[Auto]


    Channel A
    Static tRead Value..................... [9/10/11]9/10*
    tRD Phase0 Adjustment.................. [Auto]
    tRD Phase1 Adjustment.................. [Auto]
    tRD Phase2 Adjustment ................. [Auto]
    tRD Phase3 Adjustment.................. [Auto]
    Trd2rd(Different Rank)................. [Auto]
    Twr2wr(Different Rank)................. [Auto]
    Twr2rd(Different Rank)................. [Auto]
    Trd2wr(Same/Diff Rank)................. [Auto]
    Dimm1 Clock Skew Control............... [Auto]
    Dimm2 Clock Skew Control............... [Auto]
    DDR Write Training..................... [Auto]

    Channel B
    Static tRead Value..................... [9/10/11]9/10*
    tRD Phase0 Adjustment.................. [Auto]
    tRD Phase1 Adjustment.................. [Auto]
    tRD Phase2 Adjustment ................. [Auto]
    tRD Phase3 Adjustment.................. [Auto]
    Trd2rd(Different Rank)................. [Auto]
    Twr2wr(Different Rank)................. [Auto]
    Twr2rd(Different Rank)................. [Auto]
    Trd2wr(Same/Diff Rank)................. [Auto]
    Dimm1 Clock Skew Control............... [Auto]
    Dimm2 Clock Skew Control............... [Auto]
    DDR Write Training.....................[Auto]



    Motherboard Voltage Control
    Voltage Type Normal Current
    CPU Vcore........................ 1.35V [1.39375V*]
    CPU Termination.................. [auto]
    CPU PLL............................. 1.500V [Auto]
    CPU Referen........................ 0.760V [Auto]



    MCH/ICH
    MCH Core........................... 1.400V [1.38V*]
    MCH Reference.................... 0.760V [Auto]
    MCH/DRAM Ref..................... 1.150V [Auto*]
    ICH I/O........................... 1.500V [Auto]
    ICH Core......................... 1.100V [Auto]
    DRAM
    DRAM Voltage..................... 2.300V [2.18V*]
    DRAM Termination................. 1.150V [Auto*]
    Channel A Reference ............. 1.150V [Auto*]
    Channel B Reference ............. 1.150V [Auto*]

    These figures indicate what I needed to set in bios to get my memory stable at 1030 Mhz.
    I only ran memtest ,I didnt bother with prime,because I had cpu set slower than normal to remove it from the equation.
    I was hoping I would get a breakthro voltage/setting where I could clock to 1066 stable.
    It wasnt happening
    At the rate I was going I would run out of increased voltages long before 1066,and no point in commiting memory suicide.
    The figures with an * are what the pc uses for 500mhz fsb 3.5Ghz cpu.
    490 figures are in sig.

    It seems I am stuck there unless someone has more info.
    Ive seen 3 other reports of this mem having a 1000mhz limit on ud3s.
    My other options are get a higher multiplier quad or some 1066 mem.
    Since no ones giving those away just now,ill be ok as is.Seems fast enough and I dont know how high Q8200 can go on air on these anyway.
    Last edited by kick; 02-27-2009 at 05:12 AM.
    Current Systems:

    Asrock p67 Extreme6.............. Gigabyte EP-45 UD3 ...................... Gigabyte 73 PVM S2
    Intel i5 2500k 4.8ghz................ Intel Q8400 3.8ghz......................... Intel D820 2.8ghz
    Zalman 10x cooler.................... Coolermaster V8............................ HP cooler
    8GB Gskill ripjaw ddr3.............. 4GB Gskill PI ddr2.......................... 4GB samsung ddr2
    60GB ssd/500GB HDD .............. WD 1TB hdd.................................... Seagate 160GB hdd
    GTX 460 1GB x2 SLI ................. Msi 9600GT 512MB(died) ........... Onboard gx
    Win7 64 ,750w psu(ocz)............ Win7 64 ,520w psu,seasonic...... Win XP pro ,400w psu

    HEC 6A34 case . ....................... Jeantec R2 case............................ Packard Bell case

    hoping to upgrade to http://www.thinkgeek.com/stuff/41/habicase.shtml
    http://www.flixya.com/video/140325/Animal-launching

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •