Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Results 1 to 7 of 7

Thread: GA-X48T-DQ6 overclock q9450 ddr3




  1. #1
    Join Date
    Mar 2009
    Posts
    4

    Default GA-X48T-DQ6 overclock q9450 ddr3

    Hi,

    Been having bit of problems with stability.
    proc is running at 2.66GHz standard, want to overclock em to 3.2GHz and i know this is fully possible... maybe clock the rams to while im at it.
    my configuration :

    *GA-X48T-DQ6
    *Q9450 - 2.66GHz
    *OCZ Platinum Enhanced Bandwidth Edition 4GB Kit (2x2GB) 1600MHz DDR3 PC3-12800 7-6-6-24

    i had it like this but kept freezing up :

    Robust Graphics Booster___________ [Auto]
    CPU Clock Ratio ____________ [8]
    CPU Host Clock Control_ [Enabled]
    CPU Host Frequency (MHz)__________ [400]
    PCI Express Frequency (Mhz)_______ [Auto]
    C.I.A. 2__________________________ [Disabled]
    System Memory Multiplier (SPD)____ [Auto]
    DRAM Timing Selectable_______ SPD __ [Manual]
    Performance Enhance = [Standard]

    *********Standard Timing Control***********
    xCAS Latency Time - 7
    xDRAM RAS# to CAS# Delay - 6
    xDRAM RAS# tPrecharge - 6
    xPrecharge Delay (tRAS) - 24

    ********Advanced Timing Control*********
    xACT to ACT Delay (tRRD) - 4
    xRank Write to Read Delay - 5
    xWrite to Precharge Delay - 10
    xRefresh to ACT Delay - 88
    xRead to Precharge Delay - 5
    xStatic tREAD Value - 7
    xStatic tREAD Phase Adjust - 0
    xCommand Rate (CMD) - T2

    ********System Voltage Optimized********
    System voltage Control - MANUAL
    DDR3 Overvoltage Control - +0.4
    PCI-E Overvoltage Control - NORMAL
    FSB Overvoltage Control - NORMAL
    (G)MCH Overvoltage Control - NORMAL
    Loadline Calibration - AUTO
    CPU Voltage Control - 1.4000...

    so then my cpu was running at 3.2GHz and my rams at the right timings with 1.92v like intended at 1600Mhz..

    Am i doing something wrong?

    Cruise

  2. #2
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: GA-X48T-DQ6 overclock q9450 ddr3

    I would make these changes and see if you get any better results >>>

    Can you please post me a link to your ram, if not the model #? Thanks

    Robust Graphics Booster___________ [Auto]
    CPU Clock Ratio ____________ [8]
    CPU Host Clock Control_ [Enabled]
    CPU Host Frequency (MHz)__________ [401]
    PCI Express Frequency (Mhz)_______ [100]
    C.I.A. 2__________________________ [Disabled]
    System Memory Multiplier (SPD)____ [4.00A or 4.00B] <<< Try 4.00B first
    DRAM Timing Selectable_______ SPD __ [Manual]
    Performance Enhance = [Standard]

    *********Standard Timing Control***********
    xCAS Latency Time - 7
    xDRAM RAS# to CAS# Delay - 6
    xDRAM RAS# tPrecharge - 6
    xPrecharge Delay (tRAS) - 24

    ********Advanced Timing Control*********
    xACT to ACT Delay (tRRD) - 4
    xRank Write to Read Delay - 5
    xWrite to Precharge Delay - 10
    xRefresh to ACT Delay - 88
    xRead to Precharge Delay - 5
    xStatic tREAD Value - 7-10 << & may be to low, try a higher value for now
    xStatic tREAD Phase Adjust - 0
    xCommand Rate (CMD) - T2

    ********System Voltage Optimized********
    System voltage Control - MANUAL
    DDR3 Overvoltage Control - +0.4
    PCI-E Overvoltage Control - NORMAL
    FSB Overvoltage Control - +0.1
    (G)MCH Overvoltage Control - +0.2-0.3
    Loadline Calibration - AUTO
    CPU Voltage Control - 1.4000...
    Last edited by Lsdmeasap; 03-03-2009 at 12:54 AM.

  3. #3
    Join Date
    Mar 2009
    Posts
    4

    Default Re: GA-X48T-DQ6 overclock q9450 ddr3

    Link

    Will try it in a second.
    Thx at advance for the fast reply.
    Wll keep ya posted...

  4. #4
    Join Date
    Mar 2009
    Posts
    4

    Default Re: GA-X48T-DQ6 overclock q9450 ddr3

    Nope, still freezes up on me.
    Sometimes after an hour, sometimes more.

    Anything else i can try? :/

  5. #5
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: GA-X48T-DQ6 overclock q9450 ddr3

    Please post your settings again that you are now using and I will advise again

  6. #6
    Join Date
    Mar 2009
    Posts
    4

    Default Re: GA-X48T-DQ6 overclock q9450 ddr3

    Robust Graphics Booster___________ [Auto]
    CPU Clock Ratio ____________ [8]
    CPU Host Clock Control_ [Enabled]
    CPU Host Frequency (MHz)__________ [400]
    PCI Express Frequency (Mhz)_______ [100]
    C.I.A. 2__________________________ [Disabled]
    System Memory Multiplier (SPD)____ [4.00B] <<< 4.00A does not boot
    DRAM Timing Selectable_______ SPD __ [Manual]
    Performance Enhance = [Standard]

    *********Standard Timing Control***********
    xCAS Latency Time - 8 - read somewhere that 7 doesnt work with ocz rams
    xDRAM RAS# to CAS# Delay - 6
    xDRAM RAS# tPrecharge - 6
    xPrecharge Delay (tRAS) - 24

    ********Advanced Timing Control*********
    xACT to ACT Delay (tRRD) - 4
    xRank Write to Read Delay - 5
    xWrite to Precharge Delay - 10
    xRefresh to ACT Delay - 88
    xRead to Precharge Delay - 5
    xStatic tREAD Value - 10
    xStatic tREAD Phase Adjust - 0
    xCommand Rate (CMD) - T2

    ********System Voltage Optimized********
    System voltage Control - MANUAL
    DDR3 Overvoltage Control - +0.4
    PCI-E Overvoltage Control - NORMAL
    FSB Overvoltage Control - +0.1
    (G)MCH Overvoltage Control - +0.3
    Loadline Calibration - AUTO
    CPU Voltage Control - 1.412...

    This is what i was using then.
    I am thinking that it is the rams that are the major problem...?

    Thanks

  7. #7
    Lsdmeasap's Avatar
    Lsdmeasap is offline GIGABYTE Guru
    Join Date
    Jan 2008
    Location
    PCB Island
    Posts
    25,940

    Default Re: GA-X48T-DQ6 overclock q9450 ddr3

    Try this and see if things are any better. Ya, ram is likely the issue here, is it on the QVL for your board? Have you asked about it at the OCZ Forums, they may be able to tell you of known issues

    Robust Graphics Booster___________ [Auto]
    CPU Clock Ratio ____________ [8]
    CPU Host Clock Control_ [Enabled]
    CPU Host Frequency (MHz)__________ [400] << Use 401 or 399
    PCI Express Frequency (Mhz)_______ [100]
    C.I.A. 2__________________________ [Disabled]
    System Memory Multiplier (SPD)____ [4.00B] <<< 4.00A does not boot
    DRAM Timing Selectable_______ SPD __ [Manual]
    Performance Enhance = [Standard]

    *********Standard Timing Control***********
    xCAS Latency Time - 8 - read somewhere that 7 doesnt work with ocz rams (Where, sounds odd to me)

    xDRAM RAS# to CAS# Delay - 6
    xDRAM RAS# tPrecharge - 6
    xPrecharge Delay (tRAS) - 24

    ********Advanced Timing Control*********
    xACT to ACT Delay (tRRD) - 4
    xRank Write to Read Delay - 5 << Try 12
    xWrite to Precharge Delay - 10 << Try 14
    xRefresh to ACT Delay - 88
    xRead to Precharge Delay - 5 << Try 6
    xStatic tREAD Value - 10
    xStatic tREAD Phase Adjust - 0
    xCommand Rate (CMD) - T2

    ********System Voltage Optimized********
    System voltage Control - MANUAL
    DDR3 Overvoltage Control - +0.4
    PCI-E Overvoltage Control - NORMAL
    FSB Overvoltage Control - +0.1
    (G)MCH Overvoltage Control - +0.3 << Try .2-.25
    Loadline Calibration - AUTO
    CPU Voltage Control - 1.412...

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •