Please report all spam threads, posts and suspicious members. We receive spam notifications and will take immediate action!
Page 2 of 10 FirstFirst 1234 ... LastLast
Results 11 to 20 of 92

Thread: EP45-UD3P issues with BIOS, boot & ET6 (Q9550 & 4GB 1066)




  1. #11
    Join Date
    Apr 2009
    Posts
    51

    Default Re: EP45-UD3P issues with BIOS, boot & ET6 (Q9550 & 4GB 1066)

    OK...took some deep breaths and counted to ten. Can't give up!

    I'd really like to use the stability testing, but I mentioned above about having problems with that. So I played with the Memory speed...it's gotta be the RAM!

    I must have started and restarted a dozen times with the multiplier at 2.4 (800MHz) and no issues.

    When I tried the other Freq / Multiplier settings ProfJim suggested, I got multiple repeated boot failures before I was finally able to get into the BIOS. And when I did, a message upon entering MIT said: "The system has experienced boot failures because of overclocking or changes of voltages"

    Next step is to try the other channels. Like you Jim, I used 2 and 4 because of the proximity to the North bridge and the CPU's heatsink fan. Tried it...Froze up when tried 1066...gotta be bad RAM!
    Last edited by SFChief; 04-05-2009 at 01:08 PM.

  2. #12
    profJim's Avatar
    profJim is online now Chief Munchkin + moderator
    Join Date
    Dec 2008
    Location
    Tacoma, WA. [USA]
    Posts
    7,811

    Default Re: EP45-UD3P issues with BIOS, boot & ET6 (Q9550 & 4GB 1066)

    Don't give up!! We'll get you through your issues.

    re: memory slots #2 & #4

    I didn't state it clearly enough. I'm using channel A (slots #1 & #3) and have no temperature issues. I've never used channel B.

    re: 2.40 multiplier, memory @ 800 MHz
    This worked, good.
    Right now, logic (mine anyway) is that when I try the next multiplier, I don't change any other settings. If I make more than 1 bios change and I then have errors, I can't determine which of the changes caused the problem. It's possible that the 2.66 and/or 3.00 multipliers might not work, but with stock cpu speeds, they should work.

    Often times the victim....err....user ends up posting many bios templates over time. Fine.
    It's impossible for us to help out unless you post a bios template that has the current settings that are failing. Also, it will help if you post a template that shows the settings that worked. To avoid confusion, only 1 template per post, being sure to say this one is stable or this one failed. When it fails, be sure to tell us what the problem was:
    Bios error: mobo defaulted to stock settings
    Reboot Loop: my mobo barfed
    Stability test failed @ hh:mm with the folling error....

    Right now, I know that the 2.4/800 setup worked, but I don't if you applied all the suggested settings. Even if you did exactly as I suggested, I want "proof" of the settings that worked. In other threads, the user said that I tried this and it didn't work. After a few posts back & forth, we ultimately find out that some of settings were used, but not all. In some cases, they apply all the suggested settings, but also changed several other settings.ARRRG!!

    Please create a signature (color optional) similar to mine, which lists you primary components. Often, we are assisting people with similar setups and we often have to look back in the thread to find their specific setup.

    Double check that the only bios change that you made with the 2.66 setting was the memory multiplier.

    Memtest86+ cdrom creation:

    I use CDBurnerXP (freeware). Most burner programs have an option to "burn ISO". After you select this option, you'll be asked for the location of the ISO file. On my system, it's called memtest86+-2.11.iso
    After the cdrom is ready, you'll need to boot from the cdrom to run the test. Unless your cdrom is the first boot device, you'll need to press F12 as soon as you see the initial boot screen to select which device to boot from. On my system, the cdrom is setup as the first boot device. As long as my cdrom is empty or doesn't have a bootable cdrom in it, my system boots from the hard drive.

    other thoughts:

    Your trials & tribulations are just beginning, hopefully we'll have it sorted out quickly. Yes, it might be bad ram, but we need to confirm where the problem is. Practice holding your breath & counting to 10.


    Prime95 in windows is pretty simple, use:
    BLEND tests (this is the default)
    Number of torture tests to run: 4 (this might be the default with your quad)
    Check Rounding: yes (this is in the OPTIONS tab)

    Run Prime95 for at least 4 - 6 hours. I've had some errors:
    immediately (usually at high overclcoks)
    after 15 - 60 minutes (sometimes)
    after 4 - 23 hours (rarely)

    Generally, running Memtest86+ and Prime95 for four hours or more indicates that your system is stable. There are other excellent stability testing programs, but we'll get into that later.

    Bios Profiles:
    Use them, you can save up to 8 different profiles. Use a profile naming convention that works for you. I suggest something like this:
    24B333x800.5F+ (+ = stable setup, 5F => 5-5-5-15 memory timing)
    26D333x888.4C? (? = bad and/or test setup and 4C = 4-4-4-12 memory timing)

    You can't delete an existing profile, but you can replace an existing profile later with different setup and just type over the old profile name with the new name. Flashing your bios will erase all your existing profiles. Make sure that you have a hard copy for each of your test scenarios, good and bad.
    Q9650 @ 4.10GHz [9x456MHz]
    P35-DS4 [rev: 2.0] ~ Bios: F14
    4x2GB OCZ Reaper PC2-8500 1094MHz @5-5-5-15
    MSI N460GTX Hawk Talon Attack (1GB) video card <---- SLI ---->
    Seasonic SS-660XP2 80 Plus Platinum psu (660w)
    WD Caviar Black WD6401AALS 640GB (data)
    Samsung 840 Pro 256GB SSD (boot)
    SLI @ 16/4 works when running HyperSLI
    Cooler Master 120XL Seidon push/pull AIO cpu water cooling
    Cooler Master HAF XB computer case (RC-902XB-KKN1)
    Asus VH242H 24" monitor [1920x1080]
    MSI N460GTX Hawk (1GB) video card
    Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium
    HT|Omega Claro plus+ sound card
    CyberPower CP1500PFCLCD UPS
    E6300 (R0) @ 3.504GHz [8x438MHz] ~~ P35-DS3L [rev: 1.0] ~ Bios: F9 ~~ 4x2GB Kingston HyperX T1 PC2-8500, 876MHz @4-4-4-10
    Seasonic X650 80+ gold psu (650w) ~~ Xigmatek Balder HDT 1283 cpu cooler ~~ Cooler Master CM 690 case (RC-690-KKN1-GP)
    Samsung 830 128GB SSD MZ-7PC128B/WW (boot) ~~ WD Caviar Black WD6401AALS 640GB (data) ~~ ZM-MFC2 fan controller
    HT|Omega Striker 7.1 sound card ~~ Asus VH242H monitor [1920x1080] ~~ Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium ~~ CyberPower CP1500PFCLCD U.P.S
    .


  3. #13
    Join Date
    Apr 2009
    Posts
    51

    Default Re: EP45-UD3P issues with BIOS, boot & ET6 (Q9550 & 4GB 1066)

    profJim...you're awesome!

    I made the ISO disc with the exact software you use and can't seem to get the system to boot from CD. I had the same issue when I tired to reinstall VIsta from the CD. Even though I had the CDRom as the first selection and didn't even have the hard disk selected. Same thing this time around. Even though I have the CDRom as the first option and even though I used the F12 key (hard disc was selected there too even though I changed it in the BIOS) it would just bypass the CDRom and go right to the Vista boot.

    running Prime95 right now though

  4. #14
    profJim's Avatar
    profJim is online now Chief Munchkin + moderator
    Join Date
    Dec 2008
    Location
    Tacoma, WA. [USA]
    Posts
    7,811

    Default Re: EP45-UD3P issues with BIOS, boot & ET6 (Q9550 & 4GB 1066)

    Nah, semi-awesome? Maybe....

    It sounds like the cdrom might not be bootable for some reason. Did you use the "burn iso to disk" option? If you burned the ISO file to disk just like backing up a file to a cdrom, the cdrom will NOT be bootable. Try the Memtest cdrom on another computer. You must boot from the cdrom for Memtest to run.

    We can further discuss awesomeness once we have you up & running with a fully functional system.
    Q9650 @ 4.10GHz [9x456MHz]
    P35-DS4 [rev: 2.0] ~ Bios: F14
    4x2GB OCZ Reaper PC2-8500 1094MHz @5-5-5-15
    MSI N460GTX Hawk Talon Attack (1GB) video card <---- SLI ---->
    Seasonic SS-660XP2 80 Plus Platinum psu (660w)
    WD Caviar Black WD6401AALS 640GB (data)
    Samsung 840 Pro 256GB SSD (boot)
    SLI @ 16/4 works when running HyperSLI
    Cooler Master 120XL Seidon push/pull AIO cpu water cooling
    Cooler Master HAF XB computer case (RC-902XB-KKN1)
    Asus VH242H 24" monitor [1920x1080]
    MSI N460GTX Hawk (1GB) video card
    Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium
    HT|Omega Claro plus+ sound card
    CyberPower CP1500PFCLCD UPS
    E6300 (R0) @ 3.504GHz [8x438MHz] ~~ P35-DS3L [rev: 1.0] ~ Bios: F9 ~~ 4x2GB Kingston HyperX T1 PC2-8500, 876MHz @4-4-4-10
    Seasonic X650 80+ gold psu (650w) ~~ Xigmatek Balder HDT 1283 cpu cooler ~~ Cooler Master CM 690 case (RC-690-KKN1-GP)
    Samsung 830 128GB SSD MZ-7PC128B/WW (boot) ~~ WD Caviar Black WD6401AALS 640GB (data) ~~ ZM-MFC2 fan controller
    HT|Omega Striker 7.1 sound card ~~ Asus VH242H monitor [1920x1080] ~~ Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium ~~ CyberPower CP1500PFCLCD U.P.S
    .


  5. #15

    Default Re: EP45-UD3P issues with BIOS, boot & ET6 (Q9550 & 4GB 1066)

    @SFChief, do you have the AHCI enabled on the SATA controller running your CD/DVD drive? If so that may be why you can't run Memtest. The bootloader used on the Memtest is pretty old and it does not support AHCI. Assuming drive is currently connected to the NB controller (yellow port), move the connection to the on-board controller (one of the purple ports), and set the On-Board SATA/IDE Ctrl Mode to [IDE] in the Integrated Peripherials page of the BIOS and you should be able to run the Memtest without issues.
    QX9650 batch L739A761/ GA-EP45-UD3P/ Kingston KHX9200 4x1G

  6. #16
    Join Date
    Apr 2009
    Posts
    51

    Default Re: EP45-UD3P issues with BIOS, boot & ET6 (Q9550 & 4GB 1066)

    I updated my BIOS settings in this thread (first page) to reflect the first set of test settings.

    OK, ran Prime95 for 5 hours...no issues @ 800MHz.

    Got Memtest to work (I think I forgot to unzip the file before making the bootable CD).
    Ran Memtest 86+ for over 4 hours (6 passes) with no errors.

    Now bumping the frequency [400MHz] and multiplier [2.66D] to reflect 888MHz. I know this is only a test, but would one really want the (g)MCH freq Latch to be greater than the CPU host freq?

    Starting Memtest86+ at 888MHz in a few minutes...

    EDIT: Boot failure 3 times when trying to restart from the BIOS to run Memtest...at just 888MHz setting (RAM is supposed to be rated at 1066).
    Interesting that Memtest shows the RAM settings are "533MHz (DDR1066) / CAS : 5-7-7-24 / Dual Channel"...and I didn't touch those in the BIOS!

    Noticing the 533 on the second run, I stopped the process after 2 1/2 passes and went back to the 800MHz setting (333 MHz freq and 2.40B multiplier).
    And sure enough. Memtest shows the RAM settings are "400MHz (DDR800) / CAS : 5-5-5-15 / Dual Channel"

    Keeping the settings at 800MHz, I flip flopped the RAM and then moved them from slots 2 & 4 to 1 and 3 to see if one of the channels on the MB was bad.
    Settings for RAM on Memtest still shows "400MHz (DDR800) / CAS : 5-5-5-15 / Dual Channel"
    Stopped Memtest.
    Is that right?
    Pulled out a stick from channel 3 and Memtest settings for RAM was as follows: "400MHz (DDR800) / CAS : 5-5-5-15 / SINGLE Channel"
    Stopped Memtest and shut down computer.
    Swapped RAM sticks, System still booted up and Memtest gave the same message for the single channel RAM.
    So it appears that both still work in single independently.

    So I installed both sticks in channels 2 and 4 as they were originally.
    When I reboot, the system recognizes that they are in Dual Channel, so that makes me believe that the Channels are OK on the Motherboard.
    When I go into Vista, and look at my system via the Welcome center, it shows 4GB of RAM.
    So am I just misinterpreting the Memtest readings of 400MHz and 533MHz? It seems to me that they should read 800MHz and 889MHz.
    Am I missing something?
    Last edited by SFChief; 04-06-2009 at 11:51 AM.
    Gigabyte EP45-UD3P
    Intel Q9550 Quad core (2.83GHz...for now)
    Corsair HX620W Modular PSU
    Corsair DDR2 1066Mhz (2x2GB) PC2-8500C5D
    Sapphire HD4670 Ultimate
    WD velociraptor 300GB
    OCZ Vendetta 2 CPU cooler
    Vista Home Premium 64bit
    Antec Sonata Case with custom painted Fighting Illini theme

  7. #17
    profJim's Avatar
    profJim is online now Chief Munchkin + moderator
    Join Date
    Dec 2008
    Location
    Tacoma, WA. [USA]
    Posts
    7,811

    Default Re: EP45-UD3P issues with BIOS, boot & ET6 (Q9550 & 4GB 1066)

    Your 5-7-7-24 primary memory timings are the default values for your memory when the mobo can't deal with the current bios settings. When this happens, the system tries to use your settings, barfs, tries again several more times and finally gives up by setting your system to boot with the stock cpu multipler/frequency, conservative memory timings and other default bios settings..

    After your system has done the boot cycle retry loop, your bios usually has the last settings that you entered. When you enter the bios MIT section, you'll get a large red box with a general error message about your settings.

    Here's the problem:

    You made 2 major changes for the 2nd test:
    1) increased the cpu frequency from 333 to 400 (20% increase)
    2) increased the memory multiplier from 2.40 to 2.66 (10.8% increase)
    You broke the golden rule: Thou Shalt Not Make More Than 1 Major Change Per Test

    400 MHz x 2.66 = 1067 MHz memory speed a 33.3% memory speed increase can you say crash & burn?

    This is the test scenario:

    CPU Host Frequency.............333 MHz
    System Memory Multiplier.....2.40B ==> _800 MHz memory speed [1st test]
    ............................................2.66D ==> _888 MHz [2nd test]
    ............................................3.00A ==> _999 MHz [3rd test]
    ............................................3.20B ==> 1066 MHz [4th test]

    These 4 tests are designed to see if your memory is stable up to it's rated speed at stock cpu settings. In another thread, the victim had a similar problem. When he performed (the above) memory tests, he found that is Corsair 8500 memory was only stable up to 900 MHz memory speed. Problem solved? Yes. He RMA'd his ram for identical replacements and his problem is now a thing of the past. Others that have had this problem switched memory brands to correct their problem.

    After these 4 test have proven stable, we will start to gradually increase the cpu frequency, keeping the memory frequency as close possible. Clear as mud?

    When testing, I want to avoid possible file corruption that might force me to reinstall the operating system. For this reason, I always run Memtest86+ first. If it passes the extended tests, then I go into windows and run one (or more) stability test programs. FWIW, as we increase memory or cpu speeds, Memtest will complete each test loop more quickly. On my system, one test loop completes in 30 minutes.

    From now on, please post your bios settings in a new post; pass, fail or whatever.

    In the Advanced BIOS Features page, if you set Full Screen LOGO Show to Disabled, when you boot, you will see the cpu clock speed in the upper right corner of the first post screen. When running Memtest86+, it shows the current running cpu speed, primary memory timings, memory speed, and cache/memory bandwidth scores. In windows, you should use cpu-z (or other utilities) to confirm your cpu & memory settings before you start an extended stability test.
    Q9650 @ 4.10GHz [9x456MHz]
    P35-DS4 [rev: 2.0] ~ Bios: F14
    4x2GB OCZ Reaper PC2-8500 1094MHz @5-5-5-15
    MSI N460GTX Hawk Talon Attack (1GB) video card <---- SLI ---->
    Seasonic SS-660XP2 80 Plus Platinum psu (660w)
    WD Caviar Black WD6401AALS 640GB (data)
    Samsung 840 Pro 256GB SSD (boot)
    SLI @ 16/4 works when running HyperSLI
    Cooler Master 120XL Seidon push/pull AIO cpu water cooling
    Cooler Master HAF XB computer case (RC-902XB-KKN1)
    Asus VH242H 24" monitor [1920x1080]
    MSI N460GTX Hawk (1GB) video card
    Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium
    HT|Omega Claro plus+ sound card
    CyberPower CP1500PFCLCD UPS
    E6300 (R0) @ 3.504GHz [8x438MHz] ~~ P35-DS3L [rev: 1.0] ~ Bios: F9 ~~ 4x2GB Kingston HyperX T1 PC2-8500, 876MHz @4-4-4-10
    Seasonic X650 80+ gold psu (650w) ~~ Xigmatek Balder HDT 1283 cpu cooler ~~ Cooler Master CM 690 case (RC-690-KKN1-GP)
    Samsung 830 128GB SSD MZ-7PC128B/WW (boot) ~~ WD Caviar Black WD6401AALS 640GB (data) ~~ ZM-MFC2 fan controller
    HT|Omega Striker 7.1 sound card ~~ Asus VH242H monitor [1920x1080] ~~ Logitech Z-5500 Digital 5.1 Speakers
    win7 x64 sp1 Home Premium ~~ CyberPower CP1500PFCLCD U.P.S
    .


  8. #18
    Join Date
    Apr 2009
    Posts
    51

    Default Re: EP45-UD3P issues with BIOS, boot & ET6 (Q9550 & 4GB 1066)

    I never adjusted the CPU frequency...just the (G)MCH Freq Latch and the Multiplier.
    The BIOS wouldn't let me pick a D multiplier of 2.66 unless the FSB was 400MHz. But it let me do it if I changed the Freq Latch.
    The "B" multipliers for a 333 FSB go from 2.40B right up to 3.20B (i.e. 800MHz right to 1066)
    The "C" multipliers have a 2.66C but that's for a 200MHz FSB, giving 889MHz. But again, I have to change the Freq in order to get that?

    I guess I'm confused about how to get the A, C, & D multipliers without changing one of the frequencies.

    For what it's worth, I'm not worried about Windows, once I get this thing stable, I'm doing a freah install anyway. It' doesn't take that long and after all the time it's taking to get this right, it will be a breeze.

    I do have the full logo disabled.

    Is that right when I tested the system at 800MHz that is showed only 400MHz on the Memtest86?
    Last edited by SFChief; 04-06-2009 at 12:17 PM.
    Gigabyte EP45-UD3P
    Intel Q9550 Quad core (2.83GHz...for now)
    Corsair HX620W Modular PSU
    Corsair DDR2 1066Mhz (2x2GB) PC2-8500C5D
    Sapphire HD4670 Ultimate
    WD velociraptor 300GB
    OCZ Vendetta 2 CPU cooler
    Vista Home Premium 64bit
    Antec Sonata Case with custom painted Fighting Illini theme

  9. #19
    Join Date
    Apr 2009
    Posts
    51

    Default Re: EP45-UD3P issues with BIOS, boot & ET6 (Q9550 & 4GB 1066)

    Ahhhhhh!

    I figured it out! (G)MCH Freq Latch needs to be on Auto and THEN I can pick any multiplier I want!
    Gigabyte EP45-UD3P
    Intel Q9550 Quad core (2.83GHz...for now)
    Corsair HX620W Modular PSU
    Corsair DDR2 1066Mhz (2x2GB) PC2-8500C5D
    Sapphire HD4670 Ultimate
    WD velociraptor 300GB
    OCZ Vendetta 2 CPU cooler
    Vista Home Premium 64bit
    Antec Sonata Case with custom painted Fighting Illini theme

  10. #20
    Join Date
    Apr 2009
    Posts
    51

    Default Re: EP45-UD3P issues with BIOS, boot & ET6 (Q9550 & 4GB 1066)

    CRAP!
    Set the (G)MCH freq Latch to "Auto"
    Changed the multiplier to 2.66D
    Left everything else alone (including the CPU freq at 333MHz)

    System barfed 3x and Memtest shows the following settings for RAM:
    533MHz (DDR1066) / CAS : 5-7-7-24 / Dual Channel


    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Auto
    CPU Clock Ratio ..........................: 8x
    Fine CPU Clock Ratio.....................:.05
    CPU Frequency ...........................: 2.83GHz (333x8.5)

    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Enabled]
    CPU Host Frequency (Mhz) ............: 333Mhz
    PCI Express Frequency (Mhz) .........:Set to 100
    C.I.A.2 .................................:[Disabled]

    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: <<< 800
    PCI Express Clock Drive.................: <<< 900
    CPU Clock Skew (ps)....................: <<< 0
    MCH Clock Skew (ps)...................: <<< 0

    DRAM Performance Control
    Performance Enhance...................: [STANDARD]
    Extreme Memory Profile (X.M.P.).....: [Auto]
    (G)MCH Frequency Latch...............: [Auto] was 333MHz
    System Memory Multiplier ..............: 2.66D
    Memory Frequency (Mhz) ..............: 889
    DRAM Timing Selectable ................: [Manual]
    Standard Timing Control
    CAS Latency Time........................5
    tRCD .........................................5
    tRP'...........................................5
    tRAS..........................................15
    Set all Suggested below to highest Values first. Then later you can lower, one at a time, testing as you go
    Advanced Timing Control
    tRRD...........................................aut o
    tWTR..........................................auto
    tWR............................................aut o
    tRFC...........................................aut o
    tRTP...........................................aut o
    Command Rate (CMD) ....................auto
    Driving Strength Profiles
    Driving Strength ............................auto
    Channel A
    Static tRead Value.........................:auto
    tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps
    Channel B
    Static tRead Value.........................:auto
    tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps
    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................:1.23850V
    CPU Termination…..... 1.200V*.......: 1.2V
    CPU PLL…………………....1.500V*.......: 1.5V
    CPU Referen.…………....0.755V*.......: auto
    CPU Reference2………,,0.800V*.......:<<< does not exist
    MCH/ICH
    MCH Core…………….....1.100V...........: << 1.2V
    MCH Reference….…….0.800V...........; <<< auto
    MCH/DRAM Ref.…......0.900V...........: <<< auto
    I/O……………….....1.500V............: <<< 1.5V
    ICH Core…………...……1.100V............: <<< 1.1V
    DRAM
    DRAM Voltage ……....1.800V............: 2.0V
    DRAM Termination .…0.900V............: <<< 1.0V
    Channel A Reference 0.900V............: <<< 1.0V
    Channel B Reference 0.900V............: <<< 1.0V
    Advanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [DISabled]
    Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC
    Integrated Peripherals
    Legacy USB Storage Detect ..............[Enabled] *Note* Must be enabled to flash from USB
    Gigabyte EP45-UD3P
    Intel Q9550 Quad core (2.83GHz...for now)
    Corsair HX620W Modular PSU
    Corsair DDR2 1066Mhz (2x2GB) PC2-8500C5D
    Sapphire HD4670 Ultimate
    WD velociraptor 300GB
    OCZ Vendetta 2 CPU cooler
    Vista Home Premium 64bit
    Antec Sonata Case with custom painted Fighting Illini theme

Page 2 of 10 FirstFirst 1234 ... LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •